Hi,

you need to:

create a bridge
add ether1 port
add wlan1 port
put an IP address to ether1 port

It will work : D!

Works well
thank you very very much

you should give him some karma points

just done

Hi,

you need to:

create a bridge
add ether1 port
add wlan1 port
put an IP address to ether1 port

It will work : D!

Works well
thank you very very much

Is your AP a Mikrotik? If so you can achieve the same effect via EOIP tunneling.

-Nelson-

For EOIP
What need write in remote address space? wlan ip?

Is your AP a Mikrotik? If so you can achieve the same effect via EOIP tunneling.

-Nelson-

Yes It is,
How can I configure EOIP tunneling?

thanks a lot

ok I'll try thanks a lot,
but on 411/411R I have only 1 port ethernet and 1 port wlan,
is it the same?

Hi
Nobody have the same problem?
which is the correct configuration if you want bridge ethernet interface with wlan interface?

Thank you very much

From 4.9 is possible downgrade to 3.30?

http://img130.imageshack.us/img130/527/wllan.jpg Uploaded with ImageShack.us Now I'm in this situation.. but never I can ping router 192.168.1.1 from my pc, but from my wireless card all works fine and I can ping the router! Why I cannot bridge my ethernet interface with my wlan interface? thanks

thanks a lot for your kindness

now RB works again

i forgot about it . :? .. do this: interface enable <interface name> if dont remember what is the name of the interface just type : interface print 115.000 bauds and is ok :) the correct command I think is interface enable ether but after I need save the new configuration or I can reboot and the ne...

thanks a lot!
in Hyper Terminal the configuration is:

serial
port comxx
baud rate 9600
data bits 8
parity none
stop bits 1

no dts/dsr
no rts/cts
no xon/xoff

is it correct?

thank you

just click on interfase , then right click on your mouse and there is a enable command, thats all..

but from Hyper Terminal can I use a mouse? are you sure?
from Hyper Terminal I think need to use command line, is it correct? and if need to use command line wich is the correct command?

Thank you

ok!
can you please tell me the correct command by Hyperterminal for reactivate ethernet interface?

Thank you very much

:( Hi All. I made a null modem cable 2 -3, 3-2, 7-8, 8-7 5-5, 6-4,4-6 pinout. I forgot username and password and was hoping to access board via Hyper terminal. It does not seem to work. I connect cable between pc and router board, set Hyperterminal up as described in Mikrotik General information, a...

Can you please tell me if is it cross cable? (female-female)
and the connection from Hyper Terminal is ok?

thanks a lot

Hi
I tried to setup my routerboard 411/411R in bridge mode,
but accidentally I had disable Ethernet interface by Winbox, and now I cannot enter in my router (winbox doesn't find nothingh and I cannot ping it by ethernet interface!!)
How can I reset my router?

Hi

I have routerBoard 411/411R Mikrotik and I cannot bridge wlan with ethernet, now I have installed fw 4.9,
Can I downgrade to FW 3.30?
maybe I have the some your problem!

Please could you send me some info?!
I cannot understaind why doesn't work!

with station pseudobridge little better, but also doesn't work



what can I do?

Hi I have little problem with my mikrotik routerboard 411, I use winbox.. from wireless table I associated my wireless antenna Mikrotik (station mode) with the access point, If I use a ping-tools (wlan interface) I can ping the access point in 3ms perfect! But If I ping the Access Point with ping-to...

Hi I have little problem with my mikrotik routerboard 411, I use winbox.. from wireless table I associated my wireless antenna Mikrotik (station mode) with the access point, If I use a ping-tools (wlan interface) I can ping the access point in 3ms perfect! But If I ping the Access Point with ping-to...