MikroTik

Plurnay

source address and Out-Interface choose one,If a source address, such as "192.168.88.0/24" You need other people to give you recommendations I dont know your environment, I can find only these issues. I think your problem in the IP ROUTER LIST Check it focus That funky IP address & ne...

Plurnay

thanks you guys i got it working...
all I was missing was a bridge on ether2 so it could talk to the WAN port...
then after that setup ether 3,4 and 5 to use master port 2
and setup ips...

Plurnay

these are the ip's that i receive when i connect with pppoe

I can ping localy across my network... I can just not make the internet to work on the 3 last port
where could i get more help?

Plurnay

sorry bad typo...
I can now ping locally but not outside my network...

I do have my server in the DNS Setting windows...
and I added the pppoe-out2 interface on the Out-Interface for the masquerade...
what should there be on the source address

but its still doesnt work
?????

Plurnay

this is my setup from winbox...
I am not sure how my pc's are supposed to be setup
like should gibe them IP? gateway, dns? or ny
DHCP server will do all that

again this setup its not working
i cant ping anything...

let me know if I got something wrong or something missing
need help!!!

Plurnay

could somebody help me like remotely or skype with me to get this setup???
I tried everything and its just not working

Plurnay

So you mean that the only thing I would have to do is to set the pppoe and to remove the dhcp... I dont get it because when I do a system reset config the only thing its does is this: The following default configuration has been installed on your router: IP address 192.168.88.1/24 is on ether1 ether...

Plurnay

So I want to start from scratch... So I want to use the switch chip instead of using a bridge... Let me know if there something that is missing or i shouldn't do. So let say I do a system reset configuration... then setup the pppoe connection on the ether1 and a get a connection then I set ether3 , ...

Plurnay

anybody can help me on my last two post

thanks a lot

Plurnay

for the modem... i am not sure if those logs can help you but this is what I have When i plug the modem that doesnt work (but doesnt work when its connected directly to a pc) I get this.. 13:33:58 route,debug,event Interface change 13:33:58 route,debug,event interface=ether1 13:33:58 route,debug,eve...

Plurnay

So my boss want me to use the switch chip.... I think I setup it up like it suposed to be... But the internet doesnt work Need help # jun/18/2010 13:29:55 by RouterOS 4.10 # software id = RFMR-UNW4 # /interface ethernet set 0 arp=enabled auto-negotiation=yes comment="" disabled=no full-dup...

Plurnay

So like I said I got it working with a bridge...
But there is something that a really don't get... I got 3 pppoe modem on my desk
I know they are all working... but only one of them is capable of making a connection to the RB450

I got no idea why....
any one got an idea why its doing that

thanks,
PR

Plurnay

So I got it to work with a bridge... the only thing left.. would be to set it to use the switch chip
i really dont know how to do that

can someone help me with that???
thanks

Paul

Plurnay

I don't get it... why does my modem doesn't work in port 1... like i plug it in port 5 it works... i plug in port 1 it doesn't also is there anything missing except the nat/masquerade? here is my setup [admin@MikroTik] > export # jan/02/1970 00:11:12 by RouterOS 5.0beta2 # software id = RFMR-UNW4 # ...

Plurnay

I guess I replied to fast... its was working but for only the pc in ether 2...
i made some changes now my modem dont connect argh!!!

Plurnay

hey thanks bud I got it tp work...

Plurnay

1.) You don't have an IP set for the WAN interface. 2.) You don't have a NAT rule set up to NAT/Masquerade the traffic out of. 3.) You don't have a default route for the router to send traffic out of. If your ISP is handing out IPs via DHCP, you can set up a DHCP client on the WAN interface to take...

Plurnay

I thinks that what I have? but the internet is not working on any pc is there something missing /interface bridge add admin-mac=00:00:00:00:00:00 ageing-time=5m arp=enabled auto-mac=yes \ comment="" disabled=no forward-delay=15s l2mtu=1522 max-message-age=20s \ mtu=1500 name=bridge1 priori...

Plurnay

that can't be it... do i need do do anything else?

Plurnay

So I am still very new at this stuff But I got and RB450 and i want to use it to act like a switch so i got my pppoe modem into ether1... looks like this is working then I need to make the four other ports to act like a switch... i dont know how to do this.. can someone help me? thanks in avanced Pa...

Plurnay

turn out firmware wasnt working properly... downgraded to 4.10 now its works

Plurnay

after trying everything and was still not wokring
erastus coetzee suggested me to skype him so he could help me out

we found out the my firmware wasnt working properly so we downgraded to 4.10 now its works perfectly
thanks again erastus coetzee

Plurnay

thanks to erastus coetzee we found out that my firmware wasn't working properly we downgraded to 4.10 and now I can get a connection

Plurnay

So let say it doesnt work
I do have a linksys wrt54gl that works with my iburst modem...

Can I connect the wrt54gl to my RB450 and make the wrt my WAN port and use the 4 last port of my rb450 to act like a switch

If yes how... i seriously need help
hehehe
thanks,
Paul

Plurnay

Hi there.. I wasn't able to make the iburst connect with the RB450 So I plug it in a WRT54G Now I can get the connection so is that possible to connect the WRT54G to the RB450 And make it like i want it in the first place... which is connect the internet to the first port and have 4 other port act l...

Plurnay

is PPPoE client is on only to connect to a pppoe server or can be use to connect to my ISP?

Plurnay

Right now i only want the modem to connect... So I plug the my iBurst Modem in lest say port 5... Then Create a PPPoe client with my username and password is thats it??? Because I tried that and its just not working If I plug the modem directly in my PC and use my windows to connect pppoe it works f...

Plurnay

I am still not getting the modem to connect... at least I think so...
I am getting frustrated with that router...

Plurnay

Physically connecting to a port with WinBox is as easy as plugging in the wire and clicking on the 3 dots (...) next to the address. WinBox will show the MAC address and IP address assigned to the port. Click on it and connect. In general for networking, you don't "connect to a port", you...

Plurnay

Hi there thanks for your help...
for some reason Its say that i am not authorized to send pm message???

my email address is prhebert@redballinternet.com you can contact me there I will try to work on your schedule since your are the one helping me

Thanks
PR

Plurnay

hi there Zapnologica
you think you can post your setting or pm me...

I have iburst to up in canada and i am having problem getting the modem to get a connection
i need some help

Plurnay

I an having problem seting up PPPOE on my RB450 and everyone one its telling me to put my modem in port 1 but that the only port that let me connect to winbox or ssh How to i setup the RB450 so that he let me connect to windox or ssh to let say port 5? so i can troubleshoot my pppoe connection thanks

Plurnay

its not a connect cant browse...
it just doesn't connect

I change the MTU but still no luck
If i go in my log file for the pppoe connection this is what I see

I am ready to try a remote connection if anyone up for it?

Plurnay

yes i use a pppoe connection when i connect the modem directly to the pc...
works in windows and ubuntu

or if i setup the pppeo conection on the linksys WRT54GL then of course i dont have to manualy dial a connection

but I cannot make the RB450 connect yet???

Plurnay

oh yeah the modem work when plug in directly in the pc or even in a WRT-54GL Linksys but i wasnt able to make it work in the RB450 yet I am working for an iBurst ISP and we would like to use routerboards for our future projects but I cant seem to make it connect yet??? thanks that is the modem I am ...

Plurnay

I have done exactly want you just told me... But the modem is still not making a connection??? does anybody know if there is anything different in the pppoe client configuration for iburst how do I setup the microtek router so i can connected to it using winbox trought eth2... because i can only mak...

Plurnay

[admin@MikroTik] > /ip address print Flags: X - disabled, I - invalid, D - dynamic # ADDRESS NETWORK BROADCAST INTERFACE 0 ;;; default configuration 192.168.88.1/24 192.168.88.0 192.168.88.255 ether1 [admin@MikroTik] > ip route print Flags: X - disabled, A - active, D - dynamic, C - connect, S - sta...

Plurnay

I have tried that.. is it still not working..
I dont know what I am doing wrong

I only have one light on the router went I plug in the modem (the orange one)
I dont know if I have to do something diffenrent because its an iBurst connection

I need help

Plurnay

I dont know waht i am doing wrong but its just not working...
I get only one light on went i plug in the modem... (the orange one)

does anyone know if there something diffent I have to do because its iburst

Plurnay

Hi there its my first time on this forum... I think its going to be very useful from now on So i have a question I want to take my routerboard 450 and use it like a normal router So I want to have the first port to get internet from my modem (PPPOE (iBurst)) And I want the other 4 ports to be the 4 ...

Search found 40 matches