MikroTik

fresnel

Is there a way to create a default action for a particular icon in Dude? For example if you access a device via WINBOX every time can you set a double-click action to open winbox vs. right-click/tool/winbox?

fresnel

After some reading I think I found my issue with the SXT's so I thought I'd put here in case it helps others. I use the SXT's primarily as a transparent bridge. Either bridging ether1/wlan1 or ether1/vlanX. While the mac-server is enable on "*all" interfaces I found that I had to disable t...

fresnel

After some reading I think I found my issue with the SXT's so I thought I'd put here in case it helps others. I use the SXT's primarily as a transparent bridge. Either bridging ether1/wlan1 or ether1/vlanX. While the mac-server is enable on "*all" interfaces I found that I had to disable t...

fresnel

After some reading I think I found my issue with the SXT's so I thought I'd put here in case it helps others. I use the SXT's primarily as a transparent bridge. Either bridging ether1/wlan1 or ether1/vlanX. While the mac-server is enable on "*all" interfaces I found that I had to disable t...

fresnel

This happens on all SXT models. Is there resolution?

fresnel

I have not been able to mac-telnet into any of the SXT devices since I started using them. If I don't set the IP in a routable network and leave the scene it is a real problem. Is there a fix for this?

fresnel

I have just experience the exact same issue. The OmniTik reboots and comes back without a wlan1 interface! What can be done to fix this? I'm running 6.9. Is downgrading recommended?

fresnel

Is it possible to get NetFlow to transmit it's data from a loopback interface? Right now it transmits from the interface that leaves the box, whatever that may be. I need it to transmit from a loopback interface so if routing ever changes the flow source does not change. I am going to answer my own...

fresnel

Is it possible to get NetFlow to transmit it's data from a loopback interface? Right now it transmits from the interface that leaves the box, whatever that may be. I need it to transmit from a loopback interface so if routing ever changes the flow source does not change.

fresnel

we checked the code, and it says to press F

ok, will check again

Have you been able to see if this will get to work in the future?

-J

fresnel

Add my name too! I just found out yesterday the hard way that it is not supported!!

fresnel

Same issue. Did you figure out the problem?

fresnel

Hi.

I have noticed an issue lately with torch which seems to stop on it's own after a while. Just noticed this in versions of 5.x, recently in 5.8.

Is that a new feature? Or is it a problem?

Thanks,

fresnel

fewi, I'm back in this game. I have replaced a cisco router doing the interaction with the VLANs and a bridging routerboard that I was trying to do the QOS with. I've now got the RB1100 doing all the work so it also has the non-VLAN connections to the edge routing to other sites. So, I have 100% con...

fresnel

Hi. Any update on the filter? http://wiki.mikrotik.com/wiki/Manual:Troubleshooting_tools#Winbox I found it by accident. Now I see the feature is actually documented. I upgraded to 5.8 and I see it still does not work. In my opinion, there should be a button on the screen and not a key stroke that ma...

fresnel

Sweet. That would be awesome!

fresnel

I bought 4 new RB1200's and noticed that in rios 5.7 this still can not be done. Any update on this functionality? It would be very useful to us here.

fresnel

Ha. Yea, F doesn't work.

fresnel

Doesn't seem to work in 4.17 either. But I have been able to get it to come up I just can't remember how I did it! I've tried every key sequence I can think of to no avail! Any chance we can get that option put in the code??

fresnel

Anyone?

fresnel

It magically showed up on one of my consoles! So I'm posting an image of what I want to be able to turn on and off at will.

fresnel

Has anyone figured this out? I did it once and it is incredibly helpful but I can't figure out how to do it again!!!

fresnel

In what I posted there is no difference between prerouting and forward. Interface HTB happens after postrouting, even. Use what you're comfy with. Get a bench router so it's not production. Heartily recommend that. Keep it around for future experiments. I'm afraid I have had a fairly big work (prop...

fresnel

So, for one service level this is what I think you want me to try to mangle: add chain=prerouting src-address-list=SL0 action=mark-connection new-connection-mark=SL0 passthrough=yes comment="mark SL0 connection" disabled=no in-bridge-port=vlan621e2 add chain=prerouting dst-address-list=SL0...

fresnel

- don't try to mark based on interface, mark based on in-bridge-port - make queue trees that use the VLAN subinterfaces as a parent So to police a VLAN, make prerouting mangle rules - two per VLAN. One rule marks the traffic one way based on the in-bridge-port being one of the VLAN subinterface, an...

fresnel

I only had time to do some reading, but not to try it out - hence no post. But here's what I am thinking. Scenario: a bunch of VLANs going through a router need to be shaped transparently. For now, just basic rate limiting. - don't try to use just one bridge - on the two physical interfaces create ...

fresnel

I only had time to do some reading, but not to try it out - hence no post. But here's what I am thinking. Scenario: a bunch of VLANs going through a router need to be shaped transparently. For now, just basic rate limiting. - don't try to use just one bridge - on the two physical interfaces create ...

fresnel

Just for the hell of it I am going to sit down with the packet flow diagram tomorrow and try to wrap my head around that. - if actual work doesn't get in the way, that is. You're doing something I find interesting. Don't know if it can work, though.

fewi, any luck?

fresnel

I followed the examples given for what I think should work. I also reviewed the QoS_Megis.pdf file and watched the video. So I think I'm in the right spot to get this going. I think the packet flow is messed up with bridging vlans or just bridging in general. There doesn't seem to be a normal out-in...

fresnel

Just for the hell of it I am going to sit down with the packet flow diagram tomorrow and try to wrap my head around that. - if actual work doesn't get in the way, that is. You're doing something I find interesting. Don't know if it can work, though. Try the bridge interface for mangle and globals a...

fresnel

Try the bridge interface.

For the queue tree or for the mangle?

fresnel

Is it complicating things that the bridge is also trunking? I have the bridge set up to use the IP firewall as well as use IP firewall for VLAN. I can get the download queue to work using global-out HTB. When I use global-out HTB I get multiple PCQ queues. When I try to use the physical interface I ...

fresnel

Physical

fresnel

Are there any issues using interfaces that are a part of a bridge? I find that the method described in your PDF does not work in an environment with a bridge. My problem is that it appears to only create one (1) PCQ queue. That one queue gets limited by the pcq_rate. If I apply to global-out many mo...

fresnel

Hi. I would like to set up queue templates similar to Allot NetEnforcer. That is to say buckets of IP addresses that have service levels applied to them. For example: Service1 has a profile of 500kbps and 100 connections Service2 has a profile of 1024kbps and 200 connectdions In Service1 I have a &q...

fresnel

What I did was delete the rule and recreate it. I also selected the output interface to be the PPP interface. So it only NATs when the interface is active. It's been working very well this week.

fresnel

videoicu, One thing I noticed after hours of working on this is my NAT rule was not showing packets increasing. It was always 0 (zero). So, I deleted the NAT rule and recreated an exact same rule and the numbers started increasing and the connection is now working. With the old rule in place you can...

fresnel

videoicu,

You are NATting the ppp connection to Verizon, right?

fresnel

videoicu, I am having the same problem you describe. After working many hours trying to understand how the 4xxU devices are handling this USB760 and calling Verizon tech support today here is what I have learned: 1) The problem is still not solved. I thought the IP filter would help solve the proble...

fresnel

jywmpg, you are spot on with your recommendation! The firewall rule is very important in this process.

fresnel

I would like to add my two cents on the DNS suffix issue. It would be very helpful to have the ability to add a DNS Search suffix to the OS to could be appended to any short name entered on the command line.

fresnel

I upgraded to 5beta4 and the card works now. I meant to put this in a previous post in my testing the last few days but didn't get around to it. We have been dealing with some quirks but don't know if it's software related or the aircard itself. But I do have it working now.

fresnel

For the record, I can't see that it is mounting as a disk. However, on my Mac it's very annoying and will mount as a disk that has to be unmounted to use the modem. I can't help but wonder if something like this is happening on the MT. I still can't get it to be recognized on the MT for some reason.

fresnel

Doghead, One thing I noticed when I put the card in my Mac is that it mounts as an external disk. When mounted as a disk, the card would not work with my Mac either! When I unmounted it, it works just fine. I did activate with Windows to verify functionality. I now have it working with my Mac. I am ...

fresnel

I found that channel 3 for both data channel and info channel worked for my 885 on AT&T. All other values were default. I couldn't get it to work with channels 0, 1 or 2. It worked with 3 and I stopped there.

fresnel

Hi. I have a RB433UAH and I am working to get a Pantech UMW190 to be recognized so I can set up a PPP session with Verizon Wireless. I can insert the card and it boots fine. It is also recognized by the Routerboard as you can see here: [admin@MikroTik] > /system resource usb print # DEVICE VENDOR NA...

Search found 46 matches