MikroTik

yinxiangyn

for X86
Thanks

yinxiangyn

Yes, they also are needed, otherwise you are going to have problems with traffic going from and to the router. It fixed your immediate issue, but would have created new ones. Thanks again :D /ip firewall mangle add action=mark-connection chain=input disabled=no in-interface=pppoe-out1 \ new-connect...

yinxiangyn

If that's the order you have them in it won't work. You have to have all the rules with mark-connection above the rules that have an action of mark-routing. The mark-routing rules set the actual routing mark that lead to PCC load balancing for you. In your case, you're setting connection marks for ...

yinxiangyn

So do you have four more pairs of lines for 5/1 - 5/4? Can you show your entire PCC configuration? Hi fewi :) Yes,i have four more pairs of lines for 5/1 - 5/4. too long, I have not put up. /ip firewall mangle add action=mark-connection chain=input disabled=no in-interface=pppoe-out1 \ new-connecti...

yinxiangyn

Thanks Chupaka

and yes,5-lines

yinxiangyn

I want to use "both-addresses" type of load balancing for TCP 80 and 443. others use "both-addresses and ports" type of load balancing. But it seems my settings are incorrect, please help me check it Thanks :shock: add action=mark-connection chain=input disabled=no in-interface=p...

yinxiangyn

Thank you very much

I will gradually learn to understand it.

yinxiangyn

@fewi when you have time 1.Can you tell me why add 'dst-address-type=local' ,because of security reasons? 2.In addition, about load balancing, I would like to ask some questions,Hope you give me some guidance. add action=mark-connection chain=input disabled=no in-interface=pppoe-out1 \ new-connectio...

yinxiangyn

That setup is correct, though you should add 'dst-address-type=local' to those rules. Thank you fewi, I added /ip firewall nat add action=masquerade chain=srcnat disabled=no out-interface=pppoe-out1 add action=masquerade chain=srcnat disabled=no out-interface=pppoe-out2 add action=masquerade chain=...

yinxiangyn

hi all Port forwarding only works in Single-line?? I use 5-line load balancing, and sometimes find the port forwarding is not working properly(download software, sometimes the red light on) Please tell me how to set up is correct, or ignore the red light? Thanks /ip firewall nat add action=masquerad...

yinxiangyn

Unfortunately you need a new board, unless you can get the chip and have access to SMD re-working tools. Even if you replace the chip, you might find it something else. Your best hope is to replace the ethernet socket, because i think it is thru-hole mounted (so easier to replace) and it has baluns...

yinxiangyn

How far I remember this test not work for Gbit RB . If you got lightening or static electricity just replace AR8316 swich chip. No lightning or static electricity, unexplained. So step by step test, and then try to exclude it. If the switch chip, is very troublesome for me, because here it is diffi...

yinxiangyn

can someone help me

yinxiangyn

hi all
My RB450G ETH5 (PORT5) unexplained failure, does not work.
Determine the hardware problem.
now I try to resolve it,some problems need help
thanks!

Check termination resistance between Tx and Rx lines, it is to check the definition of RJ-45,between 1 and 3,or between 2 and 6???

yinxiangyn

source address and Out-Interface choose one,If a source address, such as "192.168.88.0/24" You need other people to give you recommendations I dont know your environment, I can find only these issues. I think your problem in the IP ROUTER LIST Check it focus That funky IP address & ne...

yinxiangyn

sorry bad typo... I can now ping locally but not outside my network... I do have my server in the DNS Setting windows... and I added the pppoe-out2 interface on the Out-Interface for the masquerade... what should there be on the source address but its still doesnt work ????? source address and Out-...

yinxiangyn

this is my setup from winbox... I am not sure how my pc's are supposed to be setup like should gibe them IP? gateway, dns? or ny DHCP server will do all that again this setup its not working i can ping anything... let me know if I got something wrong or something missing need help!!! :? :? First, a...

yinxiangyn

this is my setup from winbox... I am not sure how my pc's are supposed to be setup like should gibe them IP? gateway, dns? or ny DHCP server will do all that again this setup its not working i can ping anything... let me know if I got something wrong or something missing need help!!! :? :? First, a...

yinxiangyn

Anyway, will not be Garfield :lol: and @gtpro use this /ip firewall mangle add action=mark-connection chain=input disabled=no in-interface=pppoe-out1 \ new-connection-mark=pppoe-out1_conn passthrough=yes add action=mark-connection chain=input disabled=no in-interface=pppoe-out2 \ new-connection-mark...

yinxiangyn

@yinxiangyn my idea is still evolving :lol: I think that better way is add accept before rule 10 for tcp 80 port then in prerouting roules 10,11,12,13 will be the same pair of dst adres (and will be in the same mark) now 10,11,12,13 rules creates one group of dst adres pair and 14,15,16,17 creates ...

yinxiangyn

yinxiangyn

It is still working fine here, what kind of problems do you have? The use of TCP type of connection, no problem, load balancing, web browsing. Work well. For example in the use of UDP type of connection will be a problem. Such as P2P software. If NTH or src-address, src-port type of PCC, a simple s...

yinxiangyn

After 15 minutes of trying your setup I can confirm that it WORKS yinxiangyn, it is balancing 3 wans and the web proxy is working. Thank You yinxiangyn :D ! My friend, Thank you for your Karma, but I am wrong, while it does work, but some problems are not resolved. I hope I can solve it. :( Without...

yinxiangyn

so... "UDP" maybe this is not good word... I mean that yours rules not balance all traffic from clients, but only tcp protocol (without port 80) but what about for example UDP.... etc for example this rule mark all traffic from clients.... add action=mark-connection chain=prerouting comme...

yinxiangyn

After 15 minutes of trying your setup I can confirm that it WORKS yinxiangyn, it is balancing 3 wans and the web proxy is working. Thank You yinxiangyn !

You're welcome, my friend.

yinxiangyn

in my post Fri Jun 18, 2010 4:28 pm I forgot about UDP protocol ! ... so @yinxiangyn in your config I think that you should add roules for udp so you have roules 10,11,12,13 this roules mangle protocol TCP without port 80 but what about UDP ? ;p if your proxy is working on 4 wan with yours config, ...

yinxiangyn

/ip proxy access
add action=allow disabled=no dst-port=80 src-address=192.168.13.0/24
/ip proxy cache
add action=allow disabled=no dst-port=80 src-address=192.168.13.0/24

Is this your local LAN 192.168.13.0/24 ?

yes
good luck

NO!
I forgot, is the bridge

yinxiangyn

Thank you , I will try it as soon as I can and I will let you know.

interface

PS
When testing, temporary closure of the firewall filter

yinxiangyn

:lol: :lol: :lol: Ok /ip route add comment=adsl1 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=\ pppoe-out1 routing-mark=to_pppoe-out1 scope=30 target-scope=10 add comment=adsl2 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=\ pppoe-out2 routing-mark=to_pppoe-out2 scope=30 target-scope...

yinxiangyn

OK Just a moment， I just finished watching the World Cup.

yinxiangyn

Relative to the WIKI, I just made two changes, adding 80-port load balancing, and 80 ports are not marked.
And I can assure you, in my RB450G all normal. WEB-PROXY work in the four-line。
http://wiki.mikrotik.com/wiki/PCC#Appli ... _Balancing

yinxiangyn

My own family use, 4X4M ADSL, even though I overclocked to 800MHz,If used together with load balancing and WEB-PROXY, sometimes 100% CPU load,If you use in the workplace, or commercial use, the number of users a lot of it, is obviously not suitable.

yinxiangyn

Thanks Bawolek, I know what I will do next, I will buy another RB450G just to do the load balancing and a second RB450G just to do the web proxy, I think that will work. Just saw your reply Believe me, do not do this, RB450G as WEB-PROXY is incompetent, SD card capacity is too small, CPU too weak. ...

yinxiangyn

hi,everybody
Is it possible to use a Virtual Ethernet as PPPoE Client?
Thank you!

yinxiangyn

I think that having 3 pppoe with pcc and web proxy does not work well, I already tried it. Maybe web proxy only works with 1 wan :( I mean just sometimes CPU load is high, but does not mean it does not work. This is normal. You have not found a way it? In fact, there are many ways to reach。 Another...

yinxiangyn

So I am still very new at this stuff But I got and RB450 and i want to use it to act like a switch so i got my pppoe modem into ether1... looks like this is working then I need to make the for other ports to act like a switch... i dont know how to do this.. can someone help me? thanks in avanced Pa...

yinxiangyn

The most simple solution, in accordance with the example of doing so, as long as a rule. Other settings you do not need to make any changes. But do have a flaw, that is browsing the Web and HTTP downloading when there is no load balancing, only work in a single line. :D do not check the passthrough!...

yinxiangyn

I use a few days, found that while using load balancing and web-proxy, sometimes leading to high CPU occupied, especially encountered when multi-threaded HTTP download.

yinxiangyn

I'm going to try your sample configuration late tonight or very early tomorrow morning and I will let you know how it goes.

I hope you succeed, and now, I'm going to bed.

yinxiangyn

ip route add comment=adsl1 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=\ pppoe-out1 routing-mark=to_pppoe-out1 add check-gateway=ping comment=adsl1 disabled=no distance=1 dst-address=\ 0.0.0.0/0 gateway=pppoe-out1 /ip firewall mangle add action=mark-connection chain=input comment="&qu...

yinxiangyn

Could it be because I'm not using pppoe over the wan side?

I'm not sure, because I did not test such an environment.
All the web-proxy related, I have come to give you an example for reference.
Maybe other people see, and can give you recommendations.

yinxiangyn

I tried what you said but it does not work, I'm trying to get transparent web proxy to work. After I add the NAT rule to redirect traffic from port 80 to port 8080 of the proxy everything on the LAN stops, no packets can get through. :( I am sure the above settings, in my RB450G, load balance、 web-...

yinxiangyn

Destination port 80, also need to do load balancing.

yinxiangyn

Hi, I'm new to the forums but I have been reading them for a while, english is not my primary language. Can you guys tell me how to set up the mangle rules to use the web proxy when I'm using PCC load balance. This is my current set up. / ip address add address=192.168.5.1/24 network=192.168.5.0 br...

yinxiangyn

I've read a lot of post asking how we can make a load balance and web proxy can use it, to many people say that it's not possible, but yes it is, only we need to do it's mark in the output the packets go to destination port 80 and assign a routing mark, thats it. I you found this useful don't forge...

yinxiangyn

Thank you for all the replies. Although the reasons for the language, I still do not quite understand, but I'm going to try.

just view the post link'ed above, there's an a graphical example

OK, thanks again. I saw.

yinxiangyn

Thank you for all the replies. Although the reasons for the language, I still do not quite understand, but I'm going to try.

yinxiangyn

This setup ,the Web proxy does not work
But the same setup in a single WAN single PPPOE, Working properly

I need Web proxy working on this case,I hope you can understand
Thank you!

yinxiangyn

firewall nat and mangle

yinxiangyn

show us your network diagram, so we can understand what setup works and what setup doesn't work.

Thank you normis!

yinxiangyn

My setting
I wondered if I stated my thoughts accurately.

yinxiangyn

I come from China,Only speak a little English,if something wrong,Please forgive me.
I use the Web Proxy in the 4G SD card, can work when Single-WAN,but can not work when Multi-WAN.
Who can give me some tips, pictures or command.
Thank you!

yinxiangyn

I come from China, can not speak English, if rude, please forgive me.
This is the case:
I use RB450G Web Proxy in the 4G SD card, single-WAN can work, but can not work Multi-WAN.
Who can give me some tips, pictures or command.
Thank you!

Search found 53 matches