MikroTik

Aveyer

ok a simple ospf-in "accept" rule has fixed it, all routes are active. Thanks. So it seems the outgoing routes are not filtered by default? it's able to send out a default route without needing a filter to accept. And it can't be due to there being no "out filter" specified, when...

Aveyer

Filter per subnet or is there something more broad?

From my ROSV6 experience they would not populate the routing table if filtered out (denied / rejected) but I guess that has changed?

There are currently no routing filter rules.

Aveyer

Hi, I just upgraded one router (CCR1009) to ROS 7.13.5 and while OSPF v2 is functioning, for some reason all the OSPF routes are inactive in the table (see attached image).

Was something changed in ROS7? This never happened in ROS6.

Regards.

Aveyer

Don't check against just 1 IP, I check 3. This runs every 2 mins in scheduler. :if ([/ip route get [find comment="GATEWAY"] disabled]=false) do={ :if ([/ping x.x.x.x count=3] = 0 && [/ping x.x.x.x count=3] = 0 && [/ping 8.8.8.8 count=3] = 0) do={ /ip route disable [find co...

Aveyer

Hello, I recently aquired a Netonix WS-12-250-DC Switch. Here are the Spec Sheets: https://www.netonix.com/media/wysiwyg/ws-specsheet.pdf I'm actually using it powering a CCR-1009-8G-1S-1S+ with 48V 0.75A pins 4,5(+) 7,8(-), but I'm not sure that power budget (~35W) will do when using it passing fu...

Aveyer

Yea I think that's expected. A change in most OSPF settings usually causes a bounce.

Aveyer

Aveyer

I'm trying to enable / disable a specific route depending on if a default from a certain GW is in the LSA, this is what I have so far but can't get it to work. Any ideas? :if ([/ip route get [find comment="TEST"] disabled]=true) do={ :if ([/routing ospf lsa get [find id=0.0.0.0 and origina...

Aveyer

from what network did you have the local IP address that was assigned to the interfaces? Also, as Amazon states in the documentation, assigned IP address is NATed only to one internal Ip address and the virtual interfaces cannot communicate between themselves. This is my test-setup right now, inter...

Aveyer

Don't check against just 1 IP, I check 3. This runs every 2 mins in scheduler. :if ([/ip route get [find comment="GATEWAY"] disabled]=false) do={ :if ([/ping x.x.x.x count=3] = 0 && [/ping x.x.x.x count=3] = 0 && [/ping 8.8.8.8 count=3] = 0) do={ /ip route disable [find com...

Aveyer

Cheers Tom, it's very useful.

Aveyer

If you want to have 100meg available to all while also capping total bandwidth at 100meg for everyone on a /24 then you need to change the address mask from /32 to /24 in the PCQ options.

Aveyer

I've been looking for a small lightweight mini computer to run The Dude on, the new Raspberry Pi 2 + Windows 10 looks perfect.
Will The Dude run on that Windows 10 ARM platform though?

Aveyer

I have the same problem with the RBmAP2n, USB port isn't in the port list, as a result I can't add the UPS since there's no port to select.

Aveyer

I really hope Mikrotik resumes development of The Dude, out of all the network monitors I have tried, The Dude is still by far the best and easiest to use.

Aveyer

I never had a problem with MAC winbox connection with any routerboard either except for the 850Gx2.
It's not the Beta Winbox either.

Aveyer

I also had a hard time finding a way to check multiple hosts beyond a gateway, eventually I found a script on the internet which I modified. I don't have two ISPs on one interface but you can probably get it to work. My Gateway has a static default route which is then injected to the rest of the net...

Aveyer

Anyone from Mikrotik see this?

Aveyer

From the backhaul perspective I think it's better to do asymmetrical packages because even the ACKs from downloads will use a certain amount of upload. From the wireless perspective, since wireless is half duplex, if you're offering *2mb down and up* there has to be over 4mb of capacity available on...

Aveyer

I just got my first RB850Gx2 and had a hell of a time trying to configure it. It seems whenever I'm connecting to it via MAC, Winbox constantly loses connection to it, but it doesn't say "Router has been disconnected", it just sits there and everything stops updating. I tried Netinstalling...

Aveyer

I think this new look is great and was long overdue.

Aveyer

If the CRS 8 port series don't have PoE out support like the ToughSwitch I'll be seriously disappointed.

Aveyer

http://tiktube.com/?live=live

Aveyer

I also just ran into this bug, this will prevent me from doing automatic failover now...
I'm on ROS v6.18

Aveyer

Just got the mAP in my hands, it's an awesome product.
Good job Mikrotik.

Aveyer

Looking forward to the next MUM then

Aveyer

Aveyer

Has Mikrotik any plans to make an 8 port PoE switch?

I'd love to see a Mikrotik equivalent of the ToughSwitch since the TS is limiting performance due to it's undersized buffers.

Aveyer

I've no issues with routing marks here on 6.15 on RB750GL.
I upgraded from 6.12 to 6.15

Aveyer

I agree with Tomaskir, wasting time with torrent clients is crazy, Mikrotik is mainly for ISPs.
Focus on bug fixes and stability, and then update The Dude instead

Aveyer

I've no experience with NV2 so I'm curious, isn't NV2 too jittery by nature for VoIP? or is it similar to Airmax jitter/latency?

Aveyer

I upgraded all my RB450G from 5.26 to 6.12 and I don't see any ethernet issues.
They're connected to NanoBridges and Rockets.

Aveyer

I upgraded all my RB450G from 5.26 to 6.12 and they're working fine with the exception that one which wasn't connected to the network, opening the OSPF window crashed winbox until I reset the config.

If you have queue trees you may need to change from global-in/out to global.

Aveyer

I had to reset to defaults and reconfigure, then no more crashing. That is the secret to fixing many user level issues. The parsing engine is really to blame for most troubles. It's strange, there was no problem with the other 3 in production that were upgraded, just the one on my desk which was pr...

Aveyer

On one of my RB450G', opening the OSPF menu causes winbox to crash everytime. This doesn't happen on all the rest that I upgraded however, which are in production.
This router wasn't in production, it was connected directly to laptop.

I had to reset to defaults and reconfigure, then no more crashing.

Aveyer

I'm using DHCP on vlans on RB750GL and RB450G, no issues at all.

Aveyer

Upgraded from 5.26 to 6.12 on RB750GL and RB450G, so far so good.

Aveyer

Does the RB850Gx2 have 500mhz or 400mhz processor?

MUM slides say 500mhz but product brochure says 400mhz

Aveyer

Nevermind, I misread.
RB850Gx2 is dual core, hopefully it is 500mhz.

Aveyer

Core: RB750GL POE's: 1 X 8 Port Toughswitch, 1 X 5 Port Toughswitch (If only Mikrotik had something similiar ;( ) Sectors: 3 X Mikrotik Metals Backbone's: All running RB911G's Extra's: Aircam All for a NPO in Cape Town, South Africa. Site is called Saturn we like planet names ;) How did you attach ...

Aveyer

This is a little complicated so I'll explain as best I can I've a small network here of 3 sites currently which connect to eachother through bridged WDS Rocket backhauls. Each site has an RB450G and routes with OSPF, Site 2 is the only site with a ToughSwitch Pro so i'm using doing a router on a sti...

Aveyer

You need to change ARP on the LAN interface to proxy-arp.

Aveyer

Try setting a static 'admin' MAC address on the bridge. If the port that the bridge is adopting it's MAC address from leaves the bridge (or goes down), the bridge (and all VLANs on the bridge) will adopt a MAC from a different port, causing OSPF to reset. This can be prevented by setting admin-mac=...

Aveyer

None of the IPs or networks leave the routing table, just OSPF routes. As you seen in the config of Site 2, I'm using vlans on a bridge which bridges ports 1-4 because I may be using a ToughSwitch there soon. Currently the backhaul is plugged into eth1 and the AP on eth2 and when I reboot the AP, OS...

Aveyer

I'm deploying OSPF on my small network here, the problem is that whenever an interface goes down (AP reboot) OSPF and its routes also goes down, I made a loopback interface for OSPF but the problem is still happening. Here is config exports from Tiks at two sites I'm testing it with, I'm temporarily...

Aveyer

Perhaps this can help too.
http://forum.mikrotik.com/viewtopic.php?f=14&t=54881

Aveyer

updated RB750GL and RB450G (including routerboot 3.07) and all is working well.

Aveyer

.... the gateway cannot ping the edge, nor the other way around. However the routers themselves are able to ping each other when using the built in ping utility ??? which is it now, can they ping each other or not? draw a simple map to specify what is "pingable" and what isn't.. Regards S...

Aveyer

**Solved now, routes were needed in the Gateway to reach the edge but a reboot was also required before they would function** I have a problem here which is driving me nuts. I have two RB450Gs sitting on my table, testing before deployment. They are both running ROS 5.20/Routerboard 2.41 The first w...

Aveyer

Can you please add this to the RB750GL and RB450G too? and perhaps to the whole series.

Aveyer

I upgraded my new RB750GL to v5.7 and it seems less stable now .
Where can I download the old version? I think it was shipped with RouterOS V.5.2.

more details? I've upgraded my RB750GL to 5.7 and it's running fine.

Aveyer

I'd imagine you'd have to make a NAT rule too? Either srcnat or dstnat and out interface set to VPN.

Aveyer

Yes I took a look through the wiki and the packet flow pages but sometimes they confused
me more than clarifying anything, everything seems to be working fine now.
Thanks for the help.

Aveyer

My last question (I promise), would it be better to use the forward chain instead of prerouting for the connection mark?

Thanks

Aveyer

Something I just noticed in your earlier example, does passthrough need to be disabled on the packet mark? This is my current setup now and seems to be working fine: http://i74.photobucket.com/albums/i261/Mr-Photo/Mikrotik/th_pap2t-mangle-queuetree.jpg /ip firewall export # jul/27/2011 03:51:44 by R...

Aveyer

So I'll have one packet mark counting both traffic directions, how will that work with Queue Tree?
Would it be counting download traffic in the upload queue and upload in the download queue?
Thanks.

Aveyer

You should be able to see in the screenshot, the PAP2T's address is 192.168.2.2. eg. prerouting dst address=192.168.2.2 in interface=eth1-WAN postrouting src address=192.168.2.2 out interface=eth1-WAN Basically, can you give please an example of what is the correct way to have it? I might want to ca...

Aveyer

/ip address print detail Flags: X - disabled, I - invalid, D - dynamic 0 address=192.168.2.1/24 network=192.168.2.0 interface=eth4-LAN actual-interface=eth4-LAN 1 address=192.168.254.254/24 network=192.168.254.0 interface=eth1-WAN actual-interface=eth1-WAN 2 address=192.168.253.254/24 network=192.1...

Aveyer

Hi, I'm trying to setup Mangle rules for Linksys PAP2T so I can prioritise it in Queue Tree. I am trying to get Mangle to detect the PAP2T's traffic by IP address but it only seems to detect the outgoing traffic and not incoming traffic. I'm using ROS 5.5 on RB750GL, please help. http://i74.photobuc...

Aveyer

Changing the Mangle order and setting lower limit-at's seems to have fixed it.

Aveyer

Hi all, I'm a newbie to Mikrotik. I'm using an RB750GL with RouterOS 5.5 . I'm trying to prioritise game traffic (Team Fortress 2) which uses port range 27000-28000 UDP with Queue Trees. The mangle rules are seeing the traffic fine but priority only sort of works. I'm testing with a Youtube video up...

Aveyer

Thanks for that OID, CPU usage on my Nanostation 2 works!
I've noticed one problem though, when the device your monitoring/or link to it goes down, it won't resume monitoring again when it comes back up, just stays blank.

Aveyer

Hi guys, there seems to be a bug when I'm monitoring the signal strength through SNMP. It can work fine for days graphing the signal strength but then randomly stops and the only way to start it again is to recreate the data source and chart etc, ping and traffic monitoring always works properly. It...

Aveyer

The ping tool still isn't fixed either, it always reports <1ms latency when the actual latency is 3ms etc.

Aveyer

The Remove Resolved button works for me. Is there still a bug with the graphs? I have some links being monitored via SNMP, eg. one link is transferring 1.5mbps but the graph shows 5mbps, but on a different link which is transferring 2mbps the graph reports it correctly. Link is Nano2-Nano2Loco. I am...

Aveyer

Please bring back the outages link on the menu and the ability to remove resolved outages, there's absolutely no reason to remove it.
It would be very useful if The Dude had an in-built updater so no need to uninstall etc etc, saves alot of time and configuring.

Search found 66 matches