MikroTik

yogi

Well, of course a CCR1xxx can still run RouterOS v6 whereas a CCR2xxx can run only RouterOS v7 rendering it unusable in the enterprise... My point exactly, you can still buy CCR1xxx to support enterprise, it will just cost you more now. Its not an adopt or die being ROS7, just you have to pay more ...

yogi

Does this mean the CCR 1072s price is going to drop? No rather increase to $3350 vs $2795 for the 2216. All CCR1xxx have increased, but before anybody shouts foul it makes sense. In a climate of increased demand and not enough supply, why favour old technology. Were probably lucky they favour an en...

yogi

is a common designation use the term tri band router referring to a 2 x 5ghz + 1 2.4 ghz router

Perfect thank you, just checking and exactly what we want, well once we see the price.

Anybody able to help me on the Dual band LHG XL if it is 60GHz and 5,8 as there we do not need a 2,4 and 5,8?

yogi

- LHG XL HP, Gbit + SFP, Dual band High gain and output power - Audience: Home accesspoint with meshing support, Tri-Band 802.11ac, 2x 5 GHz, 2x Ethernet, LTE model with SIM slot and CAT6 modem Dual band LHG XL being 2,4 and 5,8 not 60GHz and 5,8 backup? That doesn't make sense? Audience tri-band b...

yogi

[*]802.11ad 60GHz Qualcomm and MikroTik press release

Why does the newsletter state 100m distance when 1km is achievable on that frequency:

Wireless Wire 60G Gigabit Ethernet extender that provides advanced connectivity
between buildings up to 100 meters.

yogi

Just click "Update" and it will do it. There is no need to make a new Winebottler package every time.

That was embarrassing, but thank you all good here now!!

yogi

New Winebottler has fix for El Capitan. You can download the new pre-compiled Winbox here: http://www.mikrotik.com/download/share/WinBox.zip @normis Can I ask you to please update the link to V3.0 so we can get on to routers with 6.33? If you had a formal version on the download page it would proba...

yogi

Not necessary, just tell them to read the distributor newsletter they received on the 10th July. I have issues with some of the Mikrotik designs and can get frustrated with some finishing touches on their products, but for communication they are the best out there. Their whole logistics is incredibl...

yogi

Normis is right, as how can they be responsible for shipping and distributors ordering. Here is a local supplier who received stock today a lot farther from Latvia than you are http://www.scoopdistribution.co.za/prod ... ts_id=1462

yogi

Mike thanks for all the effort on this forum.

My question to you or somebody else is why would we buy the SR5 with the XR5 available now? It seems to be a much better proposition so have you not just ended the life of the SR5 to a degree?

yogi

as this is a mikrotik-only forum, I could tell you about a new (cheap) client device that we will start selling at the end of this year.

But.. You already know what will come, a cheap CPE from Mikrotik? :D

Cost effective, well priced, affordable, but never cheap!

yogi

(dynamic queues should be disabled).

What exactly do you mean? The static queue needs to be above the dynamic, but by no means do you have to disable it.

yogi

There seem to be multiple topics in this thread. I have taken the one out to here http://forum.mikrotik.com//viewtopic.php?t=11171

yogi

My client has a situation where he wants to exclude "local traffic" from his accounting. Local traffic in this instance is everything on his internal network. The users are on usage based billing, and have been promised all local traffic will not affect their caps. Can somebody suggest a w...

yogi

That is not possible I agree, but that is why the "bug" reported by marko_bg is so interesting .... about accounting traffic, this is bug, because, one user, have transfer in one static simple queue rule 15GB (rule for FTP), and in another 5GB (dinamic rule from MT for pppoe user).... but...

yogi

RB-112 can do 3 megs no problem!

yogi

/ip firewall filter
add chain=forward dst-address=(put ip here without parenthesis) action=drop

not cool as there could be multiple "desired" domains on the IP

rather use proxy

yogi

Damn expensive IMHO, connectors Telegartner is a good call and for cable Times Microwave, both also a little pricy compared to China knockoffs, but worth the extra

Not saying you dont get more for your money with H&S just maybe not always worth it

yogi

http://wiki.mikrotik.com/wiki/Securing_ ... rOs_Router

just in case

yogi

5060-5061
10000-20000

The mark should be easy. You are doing it as UDP? Also why are you not just routing the Vonage IP as opposed to the ports?

yogi

I know I can have a watch on my primary line, but this can also cause havoc... How can this cause havoc? All I need is to get the STATUS of a pppoe-client connection. On the Interface page, whether is is R (Running) or not... I cannot find any script that can return the 'Status' of an interface. Li...

yogi

IP assigned route does not work?

You mean add a route for a specific IP the use netwatch. Does work, why not for you?

yogi

http://www.commell-sys.com/

http://www.ibase.com.tw/

English web sites well Thai-English

yogi

VIA motherboards run Mikrotik? :)

This forum and a few others will advise against using the VIA chipset. Look for Intel rather.

yogi

http://forum.mikrotik.com//viewtopic.php?t=5756 Not sure if this is the one, but perhaps the most useful I have read on this forum. Freeradius 1.1 has the Mikrotik dictionary built in so you can skip that, but the rest looked right. Post here if you have a hassle. Hey maybe log your steps and create...

yogi

"houston we have a problem"!!!!

yogi

Azureus new transport encryption is not detected.

I have Azureus 2.4.0.0 and my P2P rate limit is still working. As I am not too familiar with the program do you have to enable the encryption or does it work automatically?

yogi

Both router still need to NAT the ether1 traffic to modem1... Please advise No thats messy. Your internal range is 192.168.0.0/24 on ether3 172.16.8.x/30 on ether 1 to modem 1 172.16.8.x/30 172.16.8.y/30 on ether 2 to modem 2 172.16.8.y/30 add a route (any cheap ADSL modem/router has this facility)...

yogi

Dont double NAT i.e.:

put a /30 on ether1 and modem 1 same for ether2 and modem2

then add a route on the modems for your network via the /30's

works no problem except you still have your hassles created by load balancing

yogi

Never managed to do that as either it does nothing, or 1 of the pppoe clients takes preference. Let us know if you ever hack a solution.

Till then just let the modems handle the pppoe connection and balance over the IP's assigned to them.

yogi

You can get rid of the marks and load balance all traffic over the 2 DSL's with 1 default route. gateway=192.168.10.x,192.168.20.x You can leave the marks and specify a 3rd gateway for all the proxy traffic, also over both lines. So Network A !80 DSL1, Network B !80 DSL2, Network A&B 80 DSL1&...

yogi

change it to interface=all

if you were the bouncer for a club, would you stand outside or in?

yogi

So thats fine just put a pass through on the proxy for the WOW IP's. Then the traffic will just be natted to the fiber IP. That is what you are doing with all traffic except the http? Not much of a gamer, but does WOW use port 80 for the actual playing? Dont think I have a full understanding of your...

yogi

add name="P2P" target-addresses=ur.range.of.ips/x dst-address=0.0.0.0/0 interface=all parent=none direction=both priority=8 queue=default/default limit-at=128000/128000 max-limit=128000/128000 total-queue=default p2p=all-p2p disabled=no Put something like this above your existing simple q...

yogi

/ ip firewall nat 
add chain=dstnat src-address=!83.233.218.122 dst-address=83.233.218.122 protocol=tcp dst-port=80 action=dst-nat \
    to-addresses=192.168.0.xxx to-ports=80 comment="" disabled=no

Not sure what you tried?

yogi

You route IP's from the downlink range via the uplink? Can you not simply NAT all traffic destined to the WOW IP's to the uplink IP?

If this is useless post a little more information about your setup.

yogi

I don't want to limmit my clients connections, but I can't to harm the speed of my cutomers for cause of the P2P softwares What about limiting just the P2P traffic, or create queues with P2P being the lowest priority and no limit. If your connection is being maxed out by constant downloads your cli...

yogi

Please re-read the link above!

Sorry, read it before the last 2 posts which explains it nicely.

Still would like to see some opinions on whether they are worth the price as power does not necessarily equate to performance.

yogi

shiznit

:lol:

If you lower the power output, what benefit are you getting out of the SR2 opposed to the CM9? The CM9 has the same chipset but the SR2 is enhanced by UBNT. At a 3/1 price ratio what are you getting for your money?

You can tell us your opposition wont read this post!!!

yogi

Lots of interference around, with stability and latency as the objective, and not bandwidth. So run B on a CM9. Changing the prism chipset on the clients would be nice, but only if you can reuse the cards somewhere else. The CM9's do fail eventually if run hard, long and not ventilated properely. Wi...

yogi

/ tool netwatch add host=3.3.3.3 timeout=1s interval=1m up-script="/ip route set \[find comment=Default\] gateway=1.1.1.1" \ down-script="/ip route set \[find comment=Default\] gateway=2.2.2.2" comment="" disabled=no just add the comment Default to your route in question

yogi

/ system scheduler add name="monthend" on-event=bring2life start-date=dec/01/2005 start-time=00:00:01

you need scheduler to activate the script named "bring2life" not netwatch, but do you have to do this every month, cause I only know how to do it on consecutive periods!?!

yogi

You can create a script for changing the default gateway whenever you want, but surely you mean a script for when the link goes down? Is netwatch not what you are referring to?

Do you mean removing a specific gateway with load balancing, sorry maybe I am missing the point here.

yogi

{ :if ([/routing ospf neighbor find router-id=10.100.17.0] = "") do={ :log warning "OSPF neighbour not found !!" /interface wireless disable "name of interface" :delay 5s /interface wireless enable "name of interface" } } Hope this helps, however your OSPF pr...

yogi

That doesn't work - any other ideas??? It does work??? [yogi@Ritz - No.20] > sys log pri Flags: X - disabled, I - invalid # TOPICS ACTION PREFIX 0 info memory !ospf 1 error memory 2 warning memory 3 critical echo [yogi@Ritz - No.20] >

yogi

Would the PPP profile queue not take precedence? ~ Jason No [yogi@Home] queue simple> add name=override dst-address=1.1.1.2/32 max-limit=512000/512000 limit-at=512000/512000 [yogi@Home] queue simple> pri Flags: X - disabled, I - invalid, D - dynamic 0 name="override" dst-address=1.1.1.2/3...

yogi

What about a simple queue with the dest address of the mail server. Or was mail just the example, and you specifically need ports?

yogi

{ :if ([/interface wireless find name=xx disabled=no running=no ] != "") do={ /interface wireless disable xx :delay 5s /interface wireless enable xx /tool e-mail send to="x@x.com" subject=([/system clock get time] . " x just $%^& out ") } } Would also prefer a fix....

yogi

[yogi@Proxy] > sys reso pri uptime: 4d14h18m33s free-memory: 358948 kB total-memory: 905532 kB cpu: Pentium cpu-frequency: 993 MHz cpu-load: 97 free-hdd-space: 28548 kB total-hdd-space: 60508 kB write-sect-since-reboot: 1100 write-sect-total: 1214388 Today is a good day only 97% usage :) You can vie...

yogi

/ system logging
add topics=info,!ospf prefix="" action=memory disabled=no

:)

yogi

You guys ROCK! I will test functionality in the next RC update and give feedback where needed. Thanks again!

Sam

Sam have you had a chance to evaluate the stability for us?

yogi

Would you and your friend like to share what you have to date?

yogi

free-memory: 429096 kB total-memory: 905532 kB cpu: Pentium cpu-frequency: 993 MHz It's actually a dual 1GHz server. The HDD doesn't ever reach the maximum specified. Nor does it just get full and crash :D . What is troubling and I hope 2.9 will solve the issue. When the proxy has been running for a...

yogi

[yogi@Proxy] ip web-proxy> mon status: running uptime: 9d3h10m54s clients: 358 requests: 9292527 hits: 3728876 cache-size: 47185916 kB received-from-servers: 74438326 kB sent-to-clients: 84670863 kB hits-sent-to-clients: 12122049 kB [yogi@Proxy] ip web-proxy> pri enabled: yes src-address: x.x.x.x po...

yogi

I will make sure someone writes an example for this soon.

I would also like to see this example

yogi

wildbill showed how to limit connections from a single client /ip firewall rule forward add src-address=10.10.10.5/32 limit-count=2 you could use this next snippet for a specific server outside your network which you know the IP of: /ip firewall rule forward add dst-address=165.165.165.165/32 limit-...

yogi

registration tables - and now you get a lot more information besides connected or not

yogi

there are several other channels than 1, 6 and 11 laughable and true - channel 6 being the most abused. wifiradio - im sure you have scanned the frequencies and used the frequency-monitor to help u out. Remember isolating your distribution with walls/plates and using diffrerent polarity will also h...

yogi

We created a fix for the Atheors 5213 chipset cards that has slow performance. http://www.mikrotik.com/download/wireless-2.8.19.npk I am hesitant to just adopt these drivers without more info. After loading them to 1 repeater with only 2 clients, there is slight signal gain on the client using MK w...

yogi

[quote="wirdo"]thanx guys for suggestions. jarosoup > yes i tried and on one of the links only 5210 ghz channel is working so-so with 72-75 signal. When trying to change close to 5300 signal goes up to -85 and sometimes loosing connection. weird pays to read: adjust your datarate basic/sup...

yogi

CM9 on both sides. What frequency? Must be 2.4 with "Signal goes from -69 to -82 with clear LOS" and the distance quoted.

What version of MT? How is the data rate set? These links worked before you did what? The difference from side to side is(-69/-82 side A side B X/X?

yogi

WisperISP - exact same setup and exact same problem. Never solved it per say. Upgrade to atheros on the MT repeater and watch the log file diminish. I used to go nuts watching the logs while clients flicked on and off. The balance of the replys here dont address that problem. Even with the wireless ...

yogi

We have more than 1 site running with the same SSID. You have to have proper control in the access list. This prevents swopping from one interface to the other and sometimes being registered with both.

Bridging is bad! Nuff said.

yogi

With a /29 and 2 interfaces you arent going to go far. Can you let the clients who require the IP's dial up with PPPoE? If so enable Proxy-ARP on both interfaces and ur routing and shaping is sorted.

yogi

SATA has not worked for me. It shows in the BIOS, but thats it. Replace with an IDE and its there right away.

Search found 65 matches

Re: Newsletter 104

Re: Newsletter 104

Re: MUM Europe 2019: new hardware

Re: MUM Europe 2019: new hardware

Re: Newsletter 76

Re: Winbox on OS X 10.11 El Capitan - it's a way to fix it the easy way

Re: Winbox on OS X 10.11 El Capitan - it's a way to fix it the easy way

Re: RB-912 outdoor

Re: RB-912 outdoor

RADIUS Accounting

Re: Azureus transport encryption is not detected

Re: OSPF in Logs