MikroTik

MikroManagement

Same error here.

Will post details just now

MikroManagement

This needs to be run on the INFO channel. Obviously it will not work as init string.

MikroManagement

To turn device on: at+cfun=1

that's it

MikroManagement

Getting there slowly.... For some reason the Radio is always turned off when using in my Netbook.
Although it works when activating the radio, I Assume the radio is also off then working in Mikrotik.

My other card starts automatically

MikroManagement

Based on the status message below, can it be related tp the WCDMA channel? If so, where do I change the channel details as the at!band and similar commands give error messages? at!gstatus? (Working MC8781) !GSTATUS: Current Time: 1951 Temperature: 54 Bootup Time: 1 Mode: ONLINE System mode: WCDMA PS...

MikroManagement

I have exact MC8781 cards - same firmware version, both works 100% on my netbook with Sierra Wireless Watcher but only 1x works on my Mikrotik. The weird thing is that the card just doesn't seem to register on the network. All AT Commands like at!band at!selrat etc gives error return message. Any id...

MikroManagement

been a while, but here goes as far as I can remember. First of all, there are no generic drivers, you need to get the Windows drivers (.exe) file for your exact model. Mine was a HP un2420 so I had to get this specific driver package. Use 7-zip or similar to open / extract this file. Take the bigges...

MikroManagement

get the windows drivers for your exact model Install, extract and use MSI tools to get the following 2x files apps.mbn, amms.mbn, UQCN.mbn There might be several options, there you need to do some googling to check which files linked up with which providers etc. I have the generic UMTS driver for HP...

MikroManagement

Data channel = 1 Info channel = 1 I've also deselected the "Dial-on-demand" as this has caused me some headaches in the past. everything works 100%, except my Band selection doesn't work but it automatically switches to WCDMA after a few seconds. Took me a couple of hours to get everything...

MikroManagement

OK, I've done it. Actually quite simple - the HP / lenovo versions have other drivers / firmware than your normal Gobi 2000. Downloaded the actual HP un2420 driver, extracted the files, another extract and then some searching for the correct files. And then magically a ppp-out1 device appears, nice!!

MikroManagement

Can you please check your Vendor / Device ID under Resources -> USB

My IDs are as follows...
Vendor ID: 0x03f0
Device ID: 0x241d

{USB_DEVICE(0x03f0, 0x241d)}, /* HP un2420 Gobi QDL Device */
{USB_DEVICE(0x03f0, 0x251d)}, /* HP un2420 Gobi Modem Device */

MikroManagement

I've been struggling with this for some hours now.... Think the problem is related to the fact that my model is an HP un2420 - surely there are some indications / flags to ensure it can only be loaded on an HP notebook? My ether1 also disappears when loading the files under /firmware/. Also tried ex...

MikroManagement

OK, placed the files under the /firmware directory as per /port firmware print Now I get the following, still 0 ports for Gobi 2000 card. [admin@MikroTik] /port> print Flags: I - inactive # NAME CHANNELS USED-BY BAUD-RATE 0 serial0 1 Serial Console auto [admin@MikroTik] /port> .. [admin@MikroTik] > ...

MikroManagement

Running RouterOS 5.0rc7 with FW 2.29 + Gobi 2000 HP un2420 card. I've uploaded the 3x firmware files, connected via serial cable but not sure how to upload the firmware? My ether1 stays active, the Gobi2000 is found under Resources -> IRQ but no ports are allocated. Am I missing some details or shou...

MikroManagement

Jan/01/2002 03:00:03 router was rebooted without proper shutdown by watchdog timer.

I had an open session just before it happened- There was 8Mbps traffic between two Ethernet interfaces.

I'll double check the temperature, power adapter etc.

MikroManagement

i have exactly the same problem with almost the same config. MikroTik RB532A with daughterboard. ive upgraded the firmware, all software packages, performed a complete reset, replace the PoE with normal power supply, disabled devices not in use etc etc etc. No solution as yet, still struggling with ...

MikroManagement

Running RouterOS 2.9.46

Normal AP functioning in isolation (Default Forwarding Setting unchecked) but Wireless clients can still see each other...
Quick fix to ensure that Isolation works on Prism Cards?

MikroManagement

solved by upgrading to RouterOS 2.9.46...

MikroManagement

Mikrotik 2.9.43 RB532 By default I'm running 2x PPPoE-client interfaces on same Ethernet1. When I'm establishing a third connection, the default ("Add Default Route option") connection basically drops. Although still connected (R = Running), it doesn't transfer any data. After disconnect a...

MikroManagement

Perfect!! Thank you, I'm back online as well

MikroManagement

it actually worked on a previous version of vista

Pretty sure that it has something to do with the %APPDATA% variable.

I've deleted my MikroTik folder, and it doesn't recreate it - either not used anymore or no access

MikroManagement

I'm on wireless... No ethernet cables required

And yes, my Winbox also downloads several files

Still no solution this side.

MikroManagement

nope... still not functioning. Not UAC, defender or firewall. must be something else

It worked on my old notebook, also running Vista Ultimate.

Any other ideas?

MikroManagement

My defender and firewall disabled - still the same issue.

Will try UAC just now, but the "Run as Administrator" feature didn't work either

MikroManagement

MikroTik 2.9.38. I can connect to VPN network @ work, but cannot establish a second connection from a different computer to the same VPN network. I first need to disconnect my first computer, remove all connections (IP -> Firewall -> connections) to my work IP (port 1723 / GRE) before the second con...

MikroManagement

simple issue... I declare local variables in script, but need to see the value thereof in the output... I use plink (putty) to execute commands on my MikroTik. Actions like ppp active print returns all the values but simpler statements returns NULL. [ppp secret get [/ppp secret find name=john] passw...

MikroManagement

:local pppoe1-name ADSL_Saol0 :local pppoe2-name IBurst :local dns-name smtp.isdsl.net :local dns-ip [/ip dns static get [/ip dns static find name $dns-name] address] :local pppoe1-status ([/interface pppoe-client get [/interface pppoe-client find name $pppoe1-name] running ]) :local pppoe2-status (...

MikroManagement

:local pppoe1-name ADSL_Saol0 :local pppoe2-name IBurst :local dns-name smtp.isdsl.net :local dns-ip [/ip dns static get [/ip dns static find name $dns-name] address] :local pppoe1-status ([/interface pppoe-client get [/interface pppoe-client find name $pppoe1-name] running ]) :local pppoe2-status (...

MikroManagement

No solution... I have disabled IP Proxy, there were too many issues

MikroManagement

Anyone looking for Usage Tracking of all PPP users based on Syslog & SQL?
I've managed to get a basic version. MikroTik sends all Info logs to my Win2000 server, populates SQL database from text file

MikroManagement

I use netwatch for watching my other connections, but in this scenario it won't work due to the fact that the backup line is not always connected. I know I can have a watch on my primary line, but this can also cause havoc... All I need is to get the STATUS of a pppoe-client connection. On the Inter...

MikroManagement

Just basically need to check if the connection is active or not... The IP-assigned route does not work, any other way to see if a connection is up / down?

MikroManagement

Refer to http://forum.mikrotik.com/viewtopic.php?t=10623 for an more updated version.

MikroManagement

Refer to http://forum.mikrotik.com/viewtopic.php?t=7528 I have 2 PPPoE connections on different interfaces. As soon as my primary connection drops, it should connect on my secondary interface. The proposed solution under refered thread does not work - I cannot work with the IP address of the interfa...

MikroManagement

Seems to me I have to revert back to my Windows DHCP & DNS services...

Is there really no way to configure DNS on my Mikrotik with all DHCP leases?? Really strange

MikroManagement

MikroManagement

I did see something strange though... The DNS resolved the www address to 196.15.242.198 while my connections tab (IP -> Firewall) shows active connecions to 196.25.242.213. Ive temporarily disabled my dst-nat in order to check this. With direct masquerading (No IP proxy) everything works 100% IP Pr...

MikroManagement

I have configured IP Proxy on two of my MikroTik devices with dst-natting and everything. Transparent proxy on port 80 works fine, except for some sites....

The following site keeps on giving problem and I don't know why
http://www.education.gpg.gov.za/MatricResults/

Any help?

MikroManagement

MikroTik router configured as both DNS & DHCP server.

Any leases to clients using DHCP should be registered in DNS database. Normal feature with any DHCP server, apparently not with Mikrotik?

RouterOS v2.9.8 - Luckily I can still upgrade to v3.x someday

MikroManagement

Its there already. Just use nslookup from any client on your network. Type in the IP addr, it will return hostname

MikroManagement

running v2.9.7
When trying to change the Max. Object size property under IP - Web Proxy - Settings, it always reverts back to 4000KiB... Any idea why or way to set a bigger max object size? I have a 4Gb CompactFlash installed, but like to store objects > 4000KiB

MikroManagement

Possible to iterate through all leases to populate in DNS?

MikroManagement

Mikrotik configured as Web Proxy to accept connections on port 8080 on one of my Ethernet Interfaces. All clients connect via PPPoE / PPTP and everthing seems to work 100%. The caching works, except for some sites. Example: http://www.microsoft.com works, If I click on "Deverloper Tools", ...

MikroManagement

MikroTik router configured as both DNS & DHCP server. 6 Interfaces (subnets) used, would like to enable computers on different subnets to access eachother on pc-name / pc-name.localdomain. Way to get DHCP leases to DNS static table? I have tried without any luck. IP addresses works 100%, DNS doe...

MikroManagement

I have bought a 4Gb CompactFlash disk to enable web-caching on my Mikrotik. Did search the manual & web, but couldn't get it running.

Any ideas to configure these CF cards?

RouterBoard 500 ; Running RouterOS 2.9.7

MikroManagement

thanks!

MikroManagement

Does anyone know how to work with the EDIT / SET statements under /ppp secret

MikroManagement

I've tried to change users's (PPP secret) profiles, but cannot get it working. ppp secret edit username profile="Capped" > does not work. I have an external logging system that needs to execute scripts on my Mikrotik when users have been capped. Plink (Part of putty suite) works 100%. ppp ...

MikroManagement

Thanks!

MikroManagement

I want to switch to my backup PPPoE connection as soon as my ADSL connection drops on the one line. Actually the setup is more complex, I use 2x ADSL PPPoE connections to differentiate between local and international traffic. There are periods where both these connection cannot connect - I have acqu...

MikroManagement

No, they don't. I have configued a firewall rule to disable direct TCP/IP packets / communication. I did test it - if pingable, then Skype uses direct P2P without any traffic on my Internet line. Although I want traffic to stay local, my security should be really tightenend. I don't want all subnets...

MikroManagement

Mikrotik device configured with multiple subnets / pools with firewall rules to tighten security between users. Would like Skype traffic between (local) users to remain local ; at this stage an international supernode is used to route traffic. Possible to keep traffic local with either firewall rule...

MikroManagement

I use the script to update my IP adress on my MikroTik 2.9.13 device. Everything works... but I have 2x ADSL connections on my MikroTik and would like to update both IP addresses I did configure the full hostname and servers, but both scripts (Interface_Name and Hostname changed) do update the SAME ...

MikroManagement

I have two mikrotik devices, one acting as the main AP and the second functioning as a client on the first. All other clients open a PPPoE connection to my main AP to obtain Internet Access via NAT. The second mikrotik device have 2 wireless interfaces - typical guesthouse setup. One connect as clie...

MikroManagement

I have 2x ADSL connections on my Mikrotik. One for Local traffic, the other for international traffic...

Although I did create a script to route local traffic, I want to be able to delete these (static) routes all when needed...

Possible to delete all static routes?

MikroManagement

Weird... I have Prism cards indeed. A similar problem with these cards is that they do not support WEP / WPA... Caused me lots and lots of frustration. Even the cheapest cards in the market does support security and connect to hidden SSID's!! Any further details if the problems are related to the c...

MikroManagement

Dont double NAT i.e.: put a /30 on ether1 and modem 1 same for ether2 and modem2 then add a route on the modems for your network via the /30's works no problem except you still have your hassles created by load balancing Yogi - I do understand the /30 subnet mask, but not the double NAT idea. Both ...

MikroManagement

I have configured various MikroTik devices as Virtual Machines (Running on Microsoft Virtual Server). By using these machines as gateways, everything worked but 1) Twice-Nat used 2) Im sure there must be easier alternatives 3) MikroTik licenses The balancing worked though but I had the following pro...

MikroManagement

Why do you need Winbox when you can open a SSH tunnel to the MikroTik device? I have a I-mate K-Jam and use PocketPutty to connect to my linux servers, including MikroTik

MikroManagement

Routing is easy (as explained in the MT manual)... Just not so easy when creating two identical PPPoE tunnels to the same service provider. The gateway addresses are the same. Anyway to configure MikroTik to split local traffic between these two (or more) connections. Although I did get the setup wo...

MikroManagement

Based on PPP accounts. All session details tracked in MikroTik log. I've configured my MikroTik to send messages to Linux server. From there I copy all data in database, wrote a few scripts and now I can generate daily / weekly / monthly report based on the total Megabytes used. Email me should you ...

MikroManagement

Weird... I have Prism cards indeed. A similar problem with these cards is that they do not support WEP / WPA... Caused me lots and lots of frustration. Even the cheapest cards in the market does support security and connect to hidden SSID's!! Any further details if the problems are related to the ca...

MikroManagement

I have developed a simple SQL-based application to track PPP usage. SysLog on MikroTik send all PPP & Info messages to server. Retrieve, imports, update automatically according to User, month etc. Automated emailing to users with summary, last few sessions and quota. There are different methods ...

MikroManagement

I have a relatively simple Wireless network with one main RouterBoard (running RouterOS 2.9.11). Several clients with different hardware connect to this network successfully. I have installed a second RouterBoard (RouterOS 2.9.8) that also connects to the same network. When I configure the network t...

Search found 64 matches