PPPoE clients get disconnected though they are logged in.This happens when you use PPP--->Active connection tab to check status of PPPoE users.This is a old known bug which Mikrotik is yet to resolve.Don't use this tab,instead user PPP--->Interface tab to get active connection details,from there sel...

network.jpg Greetings, We are running services in two locations as shown in the image and are peering with provider ISP1 at both the locations.Proposing to peer with second provider ISP2 at location B. At location A we are using CCR-1036 24G-4S-EM V6.18 At Location B its 1100AHx2 V6.18 Want suggest...

The WAN (eth1) of my 450G router is configured with 59.xxx.xxx.xxx/30 IP address and the LAN (eth2) with BGP routed 110.xxx.xxx.xxx/24 IP address pool.I want to redistribute LAN side public IP pool with /28,/30 and /32 subnet to my clients.Please guide me.

planning to set up ISP service?

Got both ISP's router AS numbers.Problems resolved.Post closed.

first drop the bridge at the main router.use a FE(fast ethernet unmanged) switch,to which connect NAP1,NAP2 and PTP01.Connect the FE switch to either port1 or port2 of the router.Use Ap(WDS) and Station(wds) configuration for the PTP01 and PTP02 link.Also do the same config for the other 3 PTP links...

My ISP has issued me 59.144.abc.xyz/30 as WAN IP.I've configured the same on eth1 of RB 450G and its working fine with private Ip on eth2 in NAT mode.Now I've procured public IP block 110.172.abc.xyz/24 separately and want to configure it on eth2 in place of the private IP that I'am presently using....

you mean high interfernce right from 5.1 to 5.8 Ghz??

pls post the network diagram with ip address used

Dear Fewi

Well you can still have a network with a Mikrotik router working as a basic router (transperent packet forwarder) in conjunction with a L3 switch in L3 mode without putting a private IP in the network 2 area (with static route) i.e between mikrotik LAN and cisco L3.

Dear Ojsa

thanks a zillion.dropping the bridge did solve my problem, but only after upgrading the router firware from 4.11 to 4.17.Now I can run my network without depending on a expensive Cisco router.

Dear Uttam For wireless PtP links depending on the distance and bandwidth throughput you can use either Semiparabolic/Parabolic grid or solid state antenna.Path loss has to be calculated first for the distance first as it gives the final bandwidth throughput based on which you decide which of the tw...

Ok let me rephrase my requirement.My ISP has given me two differnet IP subnet namely abc:xyz:168:48/30 for WAN and abc:xyz:220:248/29 for router LAN side use.How do I configure the RB 450G router with these IP subnets in the most basic router mode such that I can use cisco L3 in conjunction? On the ...

If I drop the bridge then I will not get internet on eth2.Than I need to enable NAT which defeats the purpose of issuing public IP address to my clients as they will advertised with the public Ip address on eth1.What I need to know is wether the problem I'am facing is because of problem with routing...

I have configured RB450G eth1 as WAN with abc:xyz:168:48/30 series IP adddress and eth2 as LAN with abc:xyz:220:248/29 series IP subnet.Further I have bridged eth1 and eth2.Everything is fine and I can issue public IP address to my clients directtly from the router.Recently I acquired a cisco L3 for...

I'am attaching screen shot details of IP address,IP route,IP firewall and interface config on the router. internet (isp) | 122.181.13.72/30 (router WAN) | 122.181.171.192/28 (router LAN) | 122.181.171.194/28 (management server WAN)

I have configured a mikrotik RB450 OS v4.11 as a gateway router.My ISP has given me two public IP series one for the WAN with /30 netmask and another series with /28 netmask for the LAN of the router.On the LAN side of the router I have installed authentication and management server. on the WAN of t...