MikroTik

Anthonymo

A mimo wireless solution may not be your best solution here.
Consider
http://www.smallnetbuilder.com/lanwan/l ... er-roundup

Anthonymo

After you aimed with gps did you the fine tune the link? Also at a 1/4 mile your fresnel zone is around twenty feet so any little hills in between your house and his will directly block the link. Definitely raise the tower end as high as you can and have another person watch the signal strength whil...

Anthonymo

dropped back down to ver .60 and it works again

Anthonymo

I needed to have it working over night it so I unplugged the .2 network and plugged it into the 5th port until I figured it out

Anthonymo

It will, it's just bad practice. Post the output of "/ip address print detail", "/ip route print detail", "/interface print detail", "/ip firewall export", and an accurate network diagram. > /ip address print detail Flags: X - disabled, I - invalid, D - dynam...

Anthonymo

Thanks few I but I have turned off the switch already.

So will using 192.0.0.x not work?

Anthonymo

Are the clients on the 192.0.0.0/24 subnet receiving 192.0.0.1 as a default gateway? If so, this should work. Also, best practice is to use RFC1918 addresses for internal use instead of picking random IP's. Yes clients on 192.0.0.0/24 are using 192.0.0.1 as default gateway so on and so forth. My or...

Anthonymo

I have an rb750gl.
Port 1 is Wan
Port 2 is 192.0.0.1 with DHCP enabled
Port 3 is 192.0.1.1 with DHCP enabled
port 4 is 192.0.2.1 with DHCP enabled
Port 5 is nothing.

I need 192.0.0.16 to be able to ping/telnet into 192.0.2.5.
How the heck can I make that happen?

Anthonymo

So there was a trick to accomplishing what I wanted... I had to set the "master" to none on the ports I wanted to setup with a different ip / dhcpd server etc. now that I have figured that out I love these things!

Anthonymo

I'm running into this same issue.
Putty 0.61
Routeros 5.7
SSH Tunnel port 8080 to port 80
when ever I open chrome or IE to that port I get:
"Strange packet received: type 3 and disconnect.

Anthonymo

alright nevermind, by some miracle it started working again, wish I could say exactly what i did.

Anthonymo

Alright I put netinstall on a different computer and downloaded the NPK file instead of the ZIP file. I am now able to transfer the npk file via netinstall, it formats the HD, transfers the file, says it finished and i click the reboot button however the device never seems to come up, it doesn't del...

Anthonymo

I went to the download page, selected rb700 series, clicked zip file, downloaded. Unzipped the download. Fired up winbox, dragged and dropped the files into the files menu. Once the upload completed I selected the shutdown option. Once the lights went out I unplugged it and plugged it back in. Once ...

Anthonymo

From needs to be full email address not just your gateways name.

Try foo@your domain.com

Anthonymo

So i can take an RB750, run a wan connection into port 1, run a hotspot off of port 2 (with its own DHCP server) and a totally separate network (with another DHCP server) off ports 3, 4, and 5?

Anthonymo

That is what you would think but isn't the rb750 more like a four port switch with a separate upload port?

Anthonymo

If I want to take one WAN input and create 4 separate LAN's which product should I use they RB450 or the RB750?

Thank you,

Tony

PS let me know if more info is needed or if there are other questions I should be asking.

Anthonymo

http://wiki.mikrotik.com/wiki/Manual:PCC

Have a read thru that

Anthonymo

Is there a question Here?

Anthonymo

Thanks, is that the only one out of the three?

Anthonymo

Would any of these work at both ends of a 2x wireless link? Rb450g Rb250gs Rb750gl The problem is I'm transferring a large amount of files ptp across a convention center, I was running wire from one end to the other, via gb Ethernet the upload took about 30 seconds but over wireless (nano station 5m...

Anthonymo

Right, since the rb750 is the gate way eth1 needs to be connected to the dsl line acting as a router for your other equipment

Anthonymo

Couldn't you just add an example to the login page to make it clear they need to include the @domain?

Username:

ex: pat@example.com
Password:

Anthonymo

Better learn to use google

http://wiki.mikrotik.com/wiki/PPPOE_Server
http://seoroot.com/blog/networking/sett ... erver.html

Read thru those and see if that helps

Anthonymo

Wow, thank you so much for helping me and bringing that wiki page to my attention, I read the hotspot section but didn't read the customizing...

Thanks again!

Anthonymo

Thank you for helping me! I just downloaded the hotspot/login.html from my router I'm looking at this section but I'm not sure exactly what to change and to what, after i get this figured out I would like to add it to the wiki <td align="center" valign="bottom" height="175&q...

Anthonymo

Awesome! That is what i was thinking...
So lets say the hotspot network is 192.168.88.x
and the internal network is 10.1.10.x

I would need to install an accept rule to allow traffic to the gateway yes?
so 10.1.10.1 accept
Then
10.1.10.0/24 reject

Keep in mind this is my first RouterOS device.

Anthonymo

How can I make sure that hot spot users are unable to access my internal network?
If need be I can attach the Camera directly to the nano.

Anthonymo

I've been looking thru the documents,
Basically I want this to be a public hotspot, so instead of providing
user/pass I just want them to see a simple AUP and click agree.

Can someone point me to the article outlining that? or least tell me what it would be called?

Anthonymo

Nevermind I think that was some sort of splash page since my proxy server was enabled. Once I disabled the proxy everything worked as normal...

This is my very first routerOS device so I'm stumbling thru it.

Anthonymo

I know I'm allowed to go upto the next release latest revision, So when I recieved my RB750 it had 4.11 so I put 5.5 on it. It worked great until I rebooted, now it goes back to the old splash screen and shows version 3.11 I now notice that the RB750 is an os3 device... does that mean I'm only eliga...

Anthonymo

Uh-oh, does zero replies mean I'm way off?

Anthonymo

Attached is a basic sketch of what I was planning. I need to create two networks, one for an IP camera and server and one for a hotspot. The Server will be connected via ethernet to the router used at the cable modem. The IP camera and hotspot will be in a remote structure connected via a pair of UB...

Search found 33 matches

Re: I need to reach a NAS in another room at maximum speed

Re: 2x RB411r w/ Mikrotik 900mhz radios, 1/4mi apart...bad S

Re: SSH tunnels/port forwarding still doesn't work

Re: Simple routing question

Re: Simple routing question

Re: Simple routing question

Re: Simple routing question

Simple routing question

Re: More RB750 questions

Re: SSH tunnels/port forwarding still doesn't work

Re: Brand new RB750GL bricked while flashing 5.2 to 5.7?

Re: Brand new RB750GL bricked while flashing 5.2 to 5.7?

Brand new RB750GL bricked while flashing 5.2 to 5.7?

Re: please help!! Gmail mailing config

More RB750 questions

Re: RB450 or RB750

RB450 or RB750

Re: DSL Connection and bonding

Re: 4 dsl lines

Re: Which hardware would support balance-rr and gb Ethernet?

Which hardware would support balance-rr and gb Ethernet?

Re: Mikrotik setup behind UBNT gear

Re: HotSpot Login Realm

Re: Mikrotik setup behind UBNT gear

Re: How to change hotspot from user/pass to click accept

Re: How to change hotspot from user/pass to click accept

Re: Help me secure my hotspot from internal network, Please!

Help me secure my hotspot from internal network, Please!

How to change hotspot from user/pass to click accept

Re: Routerboard 750 upgrade?

Routerboard 750 upgrade?

Re: Need to create a hotspot separate from the internal netw

Need to create a hotspot separate from the internal network