no help, no thoughts, or no comments on this.

https://www.dropbox.com/s/cijdvnp3prsh49w/upload.tiff this is a picture of a router at tower base. e1 is the feed, e2 is a fail over. the others are the sectors and PtP links to other towers. i've been unable to determine the large amount on upload happening. it has always been th tx on e1 equals t...

do i need to copy the entire main routing table for each set?

a little more info i have in my routing table this 2 default routes ISP1 0.0.0.0->66.xx.xx.xx distance=1 ISP2 0.0.0.0->172.xx.xx.xx distance=2 of course all traffic goes through ISP1. in this config i ping 208.67.222.222 specifying which interface. to make sure i also did a trace route and it would ...

I'm using this http://wiki.mikrotik.com/wiki/Failover_Scripting. it does great at increasing the distance if ISP1 fails. though once it is restored it does not decrease the distance. the problem is that once the distance ISP1 is increased to 3 it will not ping anything on the internet. ISP2 has no p...

I'm using the one located at http://wiki.mikrotik.com/wiki/Failover_Scripting and it seems to be working. for a beginners some extra information would be helpful. 1) does it need to be put in a scheduler? 2) and the policies that need to be checked off.

thank you. look all over for a week for that.

a quick questions

on the script editor, there is the list of policy. is there a page for definitions for the different ones and the results?

i hoping to create a failover. is there any examples of what do to on down and up.

there doesn't appear to be a way to specify the interface under netwatch. that would seem necessary for failover.

if the router is connected to a modem that has the gateway ip address, it checks that connection. if the modem has lost internet, that is not tested and the router had no way of knowing that.

i believe the problem here is that the 2nd route needs to be already set up with a distance of 2.

on another note. does this need to be set up on a scheduler so it keeps checking or is that built in to the script already?

When you have a route set to check ping, what does it ping?

Really. No one else is having this problem!?

update3: i find that if i delete cookies I'm able to access the router. this needs to be done daily though. I'm sure there is a better fix.

update 2: that only worked for a little while.

update: i find that if i change the service port www to something other than 80 i can gain access.

I'm having same problem. does anyone have a fix?

thanks for the response. it showed up after a couple of hours and more importantly a refresh. perhaps you can help me with something else. i cannot log into any of my routers from an iOS6.1 system(iPhone or ipad). wibfig returns an "internal server error" message when password is entered.

After upgrading to 5.21 lost NTP server and can't get it back, even after downloading ntp-5.21-mipsbe.npk.

I'm unable to login to my routers through webfig from either inside the network or from the web via static IP. I'm using iPhone4s or iPad iOS6. Did not have a problem prior to upgrade.

I have a 493AH v.5.20

That's what I thought. I perhaps have a different problem.

I'm unable to login to my routers through webfig from either inside the network or from the web via static IP. I'm using iPhone4s or iPad iOS6. Did not have a problem prior to upgrade.

Are these settings in the phone or the router and where?

has any one had any experience working with a Sorenson VRS. it is used by deaf individuals for video conferencing and using ASL. after some time i found the way to get the forwarding to go through my core router and then through the Ubiquity CPE. i've added an edge router between there location and ...

thank you. i'm new to this and wanted to make sure i was understanding some of the basic principles.

i read the article at http://wiki.mikrotik.com/wiki/Testwiki/IP_addressing_and_subnetting_principles and i'm mildly confused. about 2/3 down the page an example is given of 173.120.0.0/18. this resulting in 4 subnets with a possible 62 host. addresses at 173.20.0.0, 173.20.0.64, 173.20.128, and 173....

thank you. it is in the default configuration. i added /tools macserver all and disabled the 4th(numbers 3) /ip firewall filter rules. my 493ah doesn't come with those defaults and never experienced the problem. thanx again for helping a rookie.

check if you do not have firewall in place that drops connections frm outside world to your router, as that is part of default configuration. Also, check /ip services weather you have set up some address/network from where services can be accessed. default configuration? is that referring to the mi...

check if you do not have firewall in place that drops connections frm outside world to your router, as that is part of default configuration. Also, check /ip services weather you have set up some address/network from where services can be accessed. the default configuration you mention, is that on ...

yes i can ping the IP

not able to remotely access a 750 router from the net using the static address provided by ISP. is there a setting in there I'm missing. the message i get is "because the server were this page is located isn't responding". i have no problem inside the network accessing the router using the...