MikroTik

mrphreak

Might want to post your current config (sanitised of course) otherwise people will just be guessing.

mrphreak

I take it you are aware that all Inter VLAN traffic is passed through the CPU so you won't get wire speed??

mrphreak

No, you assign it to the Master Port, which is Port 2 by default (I think, memory is a bit hazy, might be port 1) which is then accessible from any port in the switch group

mrphreak

No, but the RB800 that pizzulicchio has, should.

mrphreak

Hey Guys,

Just wondering from those of you have completed any of the Mikrotik Certifications, was it worthwhile??

Toying with the idea of running through, but it's quite an outlay, and am already tied into the Cisco and Juniper tracks but are starting to see more Mikrotik turning up.

mrphreak

Greg has some pretty good stuff floating around his site.

http://gregsowell.com/?page_id=951

mrphreak

No, leave both chains running.

mrphreak

If you're after RouterOS 6.18 for the mipsbe then it should be http://download2.mikrotik.com/routeros/ ... e-6.18.npk

Otherwise you'll have to be more specific

mrphreak

You could try reaching out to some of the registered consultants.

http://www.mikrotik.com/consultants/europe/germany

mrphreak

Personally I wouldn't use NAT.

Are the computers using the Mikrotik as their default gateway??

Can you post up the whole config of the unit??

mrphreak

By slaving the interfaces, you're using the 2 switch chips of the RB2011 (One for the GigE ports, and another for the 100s) which turns the ports into a layer 2 switch. In the simplest turns, bridging does the same, although it's run through the RB CPU instead of being processed by specific hardware...

mrphreak

If the RB411U is the default gateway for both devices you shouldn't need to do anything, it should route between them unless you have any firewall rules to prevent it.

mrphreak

Assuming the QRT5s are similarly spec'd (Antenna gain, TX Power etc) to your current back haul then there's no reason you couldn't.

mrphreak

1. Yes 2. MIMO is just what it says, Multiple In Multiple Out and isn't restricted to just two antennas at each end, 3x3 and higher are becoming more common although more for AP's than PtP or PtMP links 3. Yes, there are two antennas in the single housing, one horizontal, one vertical 4. Depends how...

mrphreak

The Dude hasn't been supported on ROS for quite some time, the package isn't even available for download anymore.

mrphreak

Which mangle rules are you having problems with specifically??

mrphreak

http://routerboard.com/Splus85DLC03D

http://routerboard.com/Splus31DLC10D

mrphreak

RIPv1 has been around since the late eighties and was a Classful routing protocol and didn't carry subnet information in the updates, so Class A addresses will be /8, Class B will be /16 and Class C will be /24 Not surprised it hasn't been noticed if it is a bug as RIP is an outdated and rarely used...

mrphreak

Sounds almost like you've got some RIPv1 happening somewhere

mrphreak

Make Port2 master of Port3. They will act as one port with MAC of Port2 so assign IP to Port2.

Does that work on x86 with NICs (I assume because he's talking of a hotspot pc with 4 interfaces)??

Otherwise create a bridge, put port 2 and 3 in it and put the ip address on the bridge

mrphreak

Needed to be able to read it a bit clearer, now my eyes are bleeding. # sep/11/2014 13:27:51 by RouterOS 6.5 # software id = FPJJ-FL3J # /interface bridge add admin-mac=4C:5E:0C:21:C3:15 auto-mac=no l2mtu=1598 name=bridge-local protocol-mode=rstp /interface ethernet set [ find default-name=ether1 ] ...

mrphreak

If they're only a metre apart, chances are you've got way too much signal.

Also there have been a few threads claiming that nv2 isn't optimised for AC yet, getting the same results with 802.11? Have you tried using N nv2?

mrphreak

http://download2.mikrotik.com/routeros/ ... k-6.18.iso

From the download page, which is working fine here

mrphreak

Also, how would I add IP addresses to the RB750 (Running as a switch), tried adding VLAN interfaces to the master port, and adding addresses to those, but no joy.

mrphreak

Cheers

Yeah, I've lost connectivity or management a few times while I'm trying to wrap my head around the implementation, which isn't fun when the two devices are 10km away.

mrphreak

And just to confuse the issue, the traffic destined for Vlan9 is currently running on 1 at the moment, planning on switching it over after other problems are sorted.

mrphreak

Hey Guys, Just got a situation where I'm running a UDP Multicast stream from ether3 on the RB750 through a mess to two output streams on the RB250 at the moment and playback is stuttering and jerking about. And I'd like to run it through the switch chip on the RB2011 to try to cut down latency and e...

mrphreak

Hey guys, Have inherited this setup which is misbehaving. There are two remote site cameras, each with RB711-5Hn cards with the wireless and ethernet bridged linking back to a RB433 with the two wireless links and ether1 bridged. When everything is running, there seems to be a bridging loop or simil...

mrphreak

If it's just for a PtP link, just try changing "ht-extension-channel=below-control" to "ht-extension-channel=above-control" and see if it accepts that

mrphreak

Looks like it's not liking "ht-extension-channel=below-control" which is possibly because 5180 is the first channel and there isn't another below it?

Might have to go back to whoever issued the command?

mrphreak

What is

/ip route
add distance=1 gateway=192.168.1.10

doing??

mrphreak

Looks like the command has carriage returns in it, and instead of sending one command, it's trying to send 5 Try /interface wireless set wlan1 adaptive-noise-immunity=ap-and-client-mode band=5ghz-onlyn basic-rates-a/g="" country=australia disabled=no frequency=5180 frequency-mode=manual-tx...

mrphreak

You might find that the port mirror is a function of the switch chip so you might need to add wan as a master-port for ether2

mrphreak

Why are you using a transparent WDS Bridge if you're using seperate networks??

mrphreak

Haven't played with the RB800/816 Combo so you might want to wait for someone more experienced to throw their hat into the ring if it's a critical service. Assuming ether1-3 are the RB800 gigabit interfaces and ether4-19 are the RB816 interfaces, so if that's wrong, you'll have to adjust as required...

mrphreak

Winbox via Mac Address an option??

mrphreak

add address=192.168.10.1/24 disabled=no interface=ether2 network=192.168.10.0

Shouldn't that be on bridge1??

mrphreak

Are ether2, 3 and 5 bridged on the RB750??

Search found 38 matches

Re: DNS and Internet access when connected through OVPN

Re: CRS125-24G-1S-2HnD-IN vlan preformance from wiki

Re: Can someone explain Mikrotik CloudRouterSwitches to me ?

Re: Feature request: Netinstall on all ports

Mikrotik Training

Re: Tutorials?

Re: Dual Chain

Re: help ???

Re: Professional Mikrotik Support

Re: connect between 2 networks on the same router

Re: Firewall on inter-bridge connections?

Re: connect between 2 networks on the same router

Re: Dual Chain

Re: Dual Chain

Re: ROS 6.20 wiped out Dude server

Re: Hello all,

Re: CRS226-24G-2S+IN

Re: RIP from Hell (RIP Bug?)

Re: RIP from Hell (RIP Bug?)

Re: Two interfece one ip address

Re: Hello all,

Re: Fastest speed and way to make a PTP Link

Re: RouterOS Downloads missing from website?

Re: Need help with VLANs and Switch Chips

Re: Need help with VLANs and Switch Chips

Re: Need help with VLANs and Switch Chips

Need help with VLANs and Switch Chips

Wireless links for IP Cameras - Possible Bridging problem?

Re: I get error when inputting command

Re: I get error when inputting command

Re: 433ah Ethernet latency

Re: I get error when inputting command

Re: Port Mirroring on RB450G router

Re: Problem with transparent bridge using WDS.

Re: Rb800 with Rb816 daughterboard configure switch chip

Re: I think I hosed my installation, forwarded all TCP ports

Re: Problem with Mikrotik and bridging

Re: Portmirroring RB750GL