MikroTik

adrcomms

I think you have missed the point. I use simple queues created by radius. In simple queues you have to tell the queue what type of queue type (profile) so we use PCQ with inside simple queues. I m sure you understand this by now. But if you don't then don't worry i can work this out for my self like...

adrcomms

here is a print ofr one simple Q that is created by radius D name="<pppoe-xxxxx@xxxxxx.co.uk>" target=<pppoe-xxxx@xxxxx.co.uk> parent=none packet-marks="" priority=6/6 queue=pppoe/pppoe limit-at=2097152/25067520 max-limit=2097152/25067520 burst-limit=5242880/33030144 burst-thresh...

adrcomms

Hi Guys Wanted to check something. We run Radius to create simple queues across our sites, the speed rate and burst works great and has for years , but one thing bugs me is the priority, we can set this in the radius and it shows in the simple queue. we use radius to create the simple queue, with ra...

adrcomms

So am i better off using EoIP for the layer 2 point to point links and have to put up with lower speeds?

Adrian

adrcomms

Thanks for you answers, when im testing im using BW test from the headend router (ccr1036) to the client end. With mrru set to 1600 i get low test, i have changed the mrru setting and the the mtu settings to lower but never get any better speeds. i understand that to get full mtu size you MLPPP does...

adrcomms

Ok so got the Ipsec working fine.

So i have l2tp+bcp working with ipsec, but when i turn on mlppp to get better mtu rates i get poor speed and fragmented packets.

MTU 1450
MRU1450
MRRU 1600

gives 1596 mtu on far end, but very bad speeds.

Thanks in advance.
Adrian

adrcomms

Hi Guys i have L2tp+bcp working, but i need to add ipsec. I have entered the ipsec secret in the l2tp server on the main site and the same on the client site, but it fails on phase 2 i have double checked the policy's and they match, but i can not get the tunnel encrypted. if i untick the ipsec box ...

adrcomms

they are all new routers and l'l running the same and latest fw, the config is a basic home ap setup

Anyway thanks for your help, i will continue just reseting the macs manually

Adrian

adrcomms

Hi Guys Been using TIK for a very long time as core devices. But we are just moving over to using hAP lite routers for customers, I have made a backup of the config with a limited webfig menu for the customers etc to make setup up routers fast fro the engineers i made a backup and then started to de...

adrcomms

Can anyone point or past a link to a better ping monitor than netwatcher. Netwatcher give to many false alarms, even if it drops one ping.

Really need a script that will run 100 ping to the target and is no reply then email, the script can be ran on a loop every 2 secs from scheduler

Adrian

adrcomms

Hi Guys Looking for some thoughts and any information or links. I would like the be able to bond multiple WAN connections over vpn tunnels. The reason for the tunnels is i want to be able to give the end user static public IP from our pool in the data centre. I have got standard bonded/load balcing ...

adrcomms

6.33rc7 is released! Changes since 6.33rc5: *) ppp - added CoA support to PPPoE, PPTP & L2TP (Mikrotik-Recv-Limit, Mikrotik-Xmit-Limit, Mikrotik-Rate-Limit, Ascend-Data-Rate, Ascend-XMit-Rate, Session-Timeout); *) pptp - improved encryption; *) ppp - added new option under "ppp aaa" -...

adrcomms

Ok so the MT GPON sfp its si only for client CPE side. The Finisar GPON unit i tried i could not get to work but i assumed this was due to the MT switches not driving the sfp unit, as you can only use MT sfp in MT devices. But i was told the MT FCT11 accepted any type of sfp, i tried the Finisar GPO...

adrcomms

Thanks Tom So if we run a CCR as my PPPOE server and run a CCS as we do now, but with a MT GPON SPF stick in the CCS at our data centre (headend) then at the clients can we use the FTC11 to convert from MT spf GPON to ethernet 1Gb, the client uses a DSL router as there local CPE, or install a RB2011...

adrcomms

Can you suggest the best way to setup a GPON network with MT at the headend

Adrian

adrcomms

For Microtick

If i buy a MT GPON stick and put this in our CCR router, and put another MT GPON stick in a MT FTC11 media converter will this work?

I purchased some Finasar GPON sticks back in Jan 15 but could not get them to link using a CCR to FTC11

Regards Adrian

adrcomms

Hi there been reading this with some interest. I have been using bonding with MT for some time now, but this has always been simple and the main route is over the two ISP connections. I have in the past set up connections for customers and have give them a public IP from our Data centre pool and rou...

adrcomms

Thats great news, so even in a CRC36 it should work? That makes Microtik Gpon compatible

Adrian

adrcomms

Thanks for the answer. As the Finisar Gpon stick is a true gpon to sfp ethernet then what your saying is that the driver onboard should should? Or does that SFP device have to be a microtik SFP ? or can you put any SFP device in the FTC i.e cisco, HP etc.

Adrian

adrcomms

Microtik staff

Will the SFP slot support any SFP device? If so will it support the Finisar GPON stick? this could be a break through in the way i deploy my be FTTH GPON network.

http://www.finisar.com/products/optical-modules/pon

https://www.youtube.com/watch?v=3ELISum9mSI

Adrian

adrcomms

Really interested in this too, we are looking a the build of our first GPON network, but would like to use Microtik.

Adrian

adrcomms

Great

Its a shame that you do not offer a AC version of the QRT5, i will have not use for the 911 board i remove.

Thanks forum

Adrian

adrcomms

So i was correct, i can replace the 911 with the 911ac board then

Adrian

adrcomms

So what is the board in the QRT5?

Adrian

adrcomms

HI Microtik

Are you looking at putting the 911ac radio in the QRT5, we need a midsize panel aerial for some sites where the sxt 16db radio is to small and the 30db dish is to large, i assume that i can install the 911ac radio the QRT5 if i pop the back off.

Adrian

adrcomms

We loaded 6.19 on our ccr 36, simple queues very fast and cpu load very low. problems: customers on pppoe started to get double ip's as we permit 2 ips per account, one for the cpe at home and the other to be used on the hotspot, never seen two ip's on other versions. hotspot started to block author...

adrcomms

We loaded 6.19 on our ccr 36, simple queues very fast and cpu load very low. problems: customers on pppoe started to get double ip's as we permit 2 ips per account, one for the cpe at home and the other to be used on the hotspot, never seen two ip's on other versions. hotspot started to block author...

adrcomms

Hi MT We have updated or CCR to 6.9 and we are still seeing port flapping, any changes to a Ethernet interface will cause the router to crash and only a hard power off and on will bring it back. Also there is still a issue with Ethernet TCP through put, we still can not use our 100mb leased line to ...

adrcomms

But the cpu isn't over loaded 1% most of the time
We also see errors when ever you plug into a Ethernet port this causes all pppoe sessions to drop?

adrcomms

Is there a fixe yet, we have been getting kernal errors, driving us mad and upsetting lots of customers.

We need a fix ASAP. These are some the errors that the MT emailed when back online

kernel failure 7
kernel failure 1
kernel failure 5
kernel failure 1970

Adrian

adrcomms

Hi There Forum I have a customer that wants 4 static public Ips from us, We have plenty if IPs as we have /22 range. We have been issuing single static ip's via pppoe accounts using radius manager, this works fine, but i can no see how to issue multiple IP's. If radius manager can not do this can an...

adrcomms

That worked great thanks, I just added ctp and udp srcnat rule

thanks Adrian

adrcomms

I only have Masq rules for the nat so all 172.16.x.x go out via the set interface i.e wan

can you give me a example

my public ip 185.32.10x.xxx and my nat range is 172.16.x.x

Adrian

adrcomms

Hi Forum I have just got a /22 ipv4 range from ripe and have a downstream carrier that is announcing my IP's. The downstream providor has given me a public ip and route to use on our router for peering and this works fine, we can access the net, i can also issue public ip's to customers can these ar...

adrcomms

I have the same issue on my MT RB1100 can you tell me the cure please Was this the MTU on the DSL pppoe or the MTU for the Internal PPPOE clients on your network. If i give the client a public static IP with the public gatewat the OWA works fine but if they are NATed or on PPPOE then OWA fails. Adrian

Search found 35 matches

Re: Simple Queue priority

Re: Simple Queue priority

Simple Queue priority

Re: L2tp+bcp+ipsec not working

Re: L2tp+bcp+ipsec not working

Re: L2tp+bcp+ipsec not working

L2tp+bcp+ipsec not working

Re: Backup config for bulk deployment

Backup config for bulk deployment

ping mon scrip wanted better than netwatcher

Bonding over VPN's

Re: v6.33rc release candidate

Re: GPON networks with Mikrotik/Routerboard SFP ports

Re: GPON networks with Mikrotik/Routerboard SFP ports

Re: GPON networks with Mikrotik/Routerboard SFP ports

Re: GPON networks with Mikrotik/Routerboard SFP ports

Re: PPTP connection bundling

Re: New?! RBFTC11

Re: New?! RBFTC11

Re: New?! RBFTC11

Re: GPON networks with Mikrotik/Routerboard SFP ports

Re: QRT5 Ac version?

Re: QRT5 Ac version?

Re: QRT5 Ac version?

QRT5 Ac version?

Re: v6.19 released

Re: v6.19rc for CCR tests needed!

Re: CLOUD CORE ROUTER

Re: CCR1016-12G Kernal Failure

Re: CCR1016-12G Kernal Failure

PPPOE Issue multiple IP's to client

Re: How to create a gateway

Re: How to create a gateway

How to create a gateway

Re: OWA (Microsoft Outlook web access) not working with PPPO