Could the guys at MT comment this issue ?

Michael

When creating a bridge interface, the bridge adopts the MAC address from one of the installed physical installed interfaces. Is there a way to change that address ? Recently i did swap some wireless interfaces, and now I have some problems as some of my bridges have mac addresses from old wireless i...

I vould be happy to test the system when your "small backup box" is ready.

Michael

I think that’s the wrong way to go. I would newer rely on a remote service for something as important as authentication service.
I would rather buy a software licence, and run the service my self.

Michael

Works for me :) (2.8.19)

Btw. im using 2.8.18 with wireless legacy driver.

I have exactly the same problem with one of my links. Some times the link locks up... client is stil connected to the ap, but cannot ping the client. Then i have to disable and enable the interface on the ap, client reconnects and i can ping it again. Im using MT brand Atheros 5211.

Michael

rx-ccq (read-only: integer: 0..100) - Client Connection Quality - a value in percent that shows how effective the receive bandwidth is used regarding the theoretically maximum available bandwidth tx-ccq (read-only: integer: 0..100) - Client Connection Quality - a value in percent that shows how effe...

CCQ (client connection quality)

Michael

Thanks for fast reply Eugene....

Does MT support S-ATA discs ?

Yes, i'm aware that it can be done in webproxy. But it would be nice to do it whitout having to enable webproxy. Directly in firewall......

Is it possible to do content filtering / url filtering in MT ? If not, that would be a nice feature :)

Hopefully not before the package is 100% stable.

You ca use DHCP with bandwidth control...

Dale: 2.8.13 is in your mailbox...


My experince with 2.8.17;

Latency problems.
Big problems using RB14 (Wireles disconnects every 1 minute)
Wireless disconnects on hevy load.
Signal strength jumps up and down, changing wireless rate.

You could bridge the 2 interfaces.

You can downgrade your system by uploading the packages you want via ftp. then in terminal window; After that just reboot your system

Paste this code in your terminal window;

NAT problem ?

I finaly found the problem. It is a problem with the RB14 board. Installing 4 RB11 instead, solved the disconnect problem. I never had this problem with earlier versions.

Yes, i admit it sounds weird. I dont think it's a hardware problem as i'm using both RB230, intel, and VIA mainboards and it dossent seem to matter witch platform running. Radios are all MT brand.

Of course i could reinstall all of it... but i have about 40 MT's most of then in towers.

Does anyone have a followup on this issue? Upgrading my systems to 2.8.17 only made tings more unreliable. I have a mix of 5211 and 5212 on varius hardware platforms. With erlier versions (2.8 and 2.7) this never was a problem. When trying to downgrade the systems back to an older vs. only made more...

Running Epia 800 mhz, 1 Atheros 5211, 2 5212. system resource> pr uptime: 30d12h49m57s free-memory: 97452 kB total-memory: 119296 kB cpu: VIA cpu-frequency: 800 MHz cpu-load: 1 free-hdd-space: 19934 kB total-hdd-space: 61484 kB write-sect-since-reboot: 26514 write-sect-total: 104680 system resource ...

Remember, only 50 PPPoE connections in Win2003 server standard edition!

You have to have Enterprise or datasenter server to have more than 50 cons.

michaelg

Mainbord: EPIA-V8000 and EPIA-V10000 Low power consumtion and low heat. Uses powerkit and POE injector ; http://www.highgreen.nl/products/dcpower/power.asp?id=15198&supplier=1000 With PCI riser card and Routerboard14 adapter you can use up to 8 wireless minipci cards. My routers works fine with ...

I have several MT routers with VIA Epia and Athros running. Works like a charm :)

Michaelg