MikroTik

ytuxedo002

Hey guys, I'm trying to configure QoS for 2 different WANS that are setup for failover. The issue i'm having is currently our phones are going through one WAN and Data is going through the other. Data has a 10/2 connection and the phones have a T1 1.5/1.5Mb connection. I need to be able to have QoS ...

ytuxedo002

Two things you can check 1. make sure you turn off the SIP alg helper: /ip firewall service-port disable sip 2. On the yealink phones go to "Accounts" then "Advanced" and under Local SIP Port make sure your phones have different ports (5060,5061..etc..) Number 2 is usually not ne...

ytuxedo002

This is what we use. But we found that the speeds don't actually match what they have. For example: If the customer has 50Mbps down and i put that in the parent rule, they will not get even close to 50, more like 16. If i turn off that rule or change it to 200M then they get the 50. Am i doing some...

ytuxedo002

This is what we use. But we found that the speeds don't actually match what they have. For example: If the customer has 50Mbps down and i put that in the parent rule, they will not get even close to 50, more like 16. If i turn off that rule or change it to 200M then they get the 50. Am i doing somet...

ytuxedo002

What is the ether config like? Are the ports switched or bridged? It's exactly like it comes from factory. The LAN ip is set on Bridge-local /interface bridge port add bridge=bridge-local interface=ether2 add bridge=bridge-local interface=ether3 add bridge=bridge-local interface=ether4 add bridge=b...

ytuxedo002

Guys, I have a client that currently has a RB2011UiAS-2HnD installed and they are paying for a 100Mb comcast circuit. The issue is when they have the mikrotik connected they are getting around 60Mb download. If we connect directly to the comcast modem we get over 100Mb. 60Mb is more than enough spee...

ytuxedo002

Nobody else is having this issue?

ytuxedo002

Guys i'm getting a runtime error when trying to login to our MT through winbox. I was able to login just fine right before the upgrade. What broke???

ytuxedo002

Place the WAN address you want for the phones on a bridge or switch that contains a) the port that the ISP is coming in on b) the logical "WAN" port for your voice network and c) the logical "WAN" port for your data network. Only assign the address(es) you want to use on the mik...

ytuxedo002

Guys, I've been scouring the Google for some time now and cannot find a straight answer on how to get a public IP setup behind a MT. My current situation is that i have a bridged comcast router->Mikrotik with a Static IP->Sonicwall that requires a static ip. We do have a block of IP's availble. The ...

ytuxedo002

Guys, I need some help here. I have an RB2011UiAS-2HnD with a basic config on 6.18. There are only 5 IP phones attached to this router. SIP helper is turned off. I have 4 mangle rules marking packets to the SIP server and simple queue rules prioritizing this traffic. I have about 100 of these setup ...

ytuxedo002

Anybody have an answer on this? I have had two devices, one CRS125-24G-1S-2HnD-IN and one RB2011UiAS-2HnD-IN. I upgraded both to 6.19 and they just crapped out. They kept rebooting not letting me even access the software. I then downgraded the RB2011UiAS-2HnD-IN to 6.18 and it worked for a while un...

ytuxedo002

Anybody have an answer on this? I have had two devices, one CRS125-24G-1S-2HnD-IN and one RB2011UiAS-2HnD-IN. I upgraded both to 6.19 and they just crapped out. They kept rebooting not letting me even access the software. I then downgraded the RB2011UiAS-2HnD-IN to 6.18 and it worked for a while unt...

ytuxedo002

Any one?

ytuxedo002

Is there a way to "push" Interface graphing (/tools/graphing) to the dude server? Kinda like a syslog.

Thank you for any assistance.

ytuxedo002

I'm having an issue with NTP on upgrading. None of my boxes will grab time anymore. I'm not sure what to do. It is affecting some of my services. I have tried several ntp servers, i have disabled and enabled. It will convert the names to IP's but it will not update time. Any suggestions? I have the ...

ytuxedo002

you can create another group for admin users without be super users: /user group add name=near-full policy="local,telnet,ssh,ftp,reboot,read,write,test,winbox,web,sniff,api,sensitive,password,!policy" Beautiful. I will implement this and let you know how it works out. But I can tell that ...

ytuxedo002

There is a concept called RAIN: Redundant Array of Internet Nodes Redundant Array of Independent Nodes Redundant Array of inexpensive Networks Redundant Array of Internet Networks How ever you want to phrase it, the point is that the concept refers in some way creating a Network along multiple path...

ytuxedo002

Hey guys and gals, i got a quick one. I basically need two admin accounts but I need that the second one to have admin access but not be able to delete/disable/change pw on the first user. What i need is access for our engineers to manage the MT's but also let the local admin have access as well but...

ytuxedo002

I was wondering if it was possible to monitor the DNS name instead of the IP of Mikrotiks. I am starting to use the new cloud option with clients that have dynamic ips. I used the DNS name that was given in the IP of the device but it will not take a name. Any ideas? Thanks Ok I think I figured thi...

ytuxedo002

I was wondering if it was possible to monitor the DNS name instead of the IP of Mikrotiks.

I am starting to use the new cloud option with clients that have dynamic ips. I used the DNS name that was given in the IP of the device but it will not take a name.

Any ideas?

Thanks

ytuxedo002

I used ordinary ftp to upload the files to the router like this. ftp 192.168.1.88 Name (192.168.1.88:root): admin Password: ftp>bin ftp>hash ftp>mkdir cisco ftp>cd cisco ftp>put SIPDefault.cnf ftp>bye Do you use the user admin ??? I've just always dragged and dropped the files into winbox.

ytuxedo002

I doing the same, but am not at home now. So i can't see my config. But when i maked my config, i created a folder called cisco on the mikrotik and put the cisco files there. And then directed the tftp files to that directory. like SIPDefault.cnf ------> cisco/SIPDefault.cnf I tried your method and...

ytuxedo002

Missing one file ??

SIPDefault.cnf

http://www.norgie.net/documentation/cis ... ndex.shtml

Sorry I forgot to put that in my previous post. Those files are present but still get same error.

ytuxedo002

Guys, I seem to be having a similar issue with TFTP. I'm running 6.13(just upgraded to see if it would help, was on 5.24 before) I have some files for a cisco 7940 that i'm trying to upgrade to SIP. I am able to do this just fine using TFTP server on my local machine and the phone does everything it...

ytuxedo002

Wiki: Wireless_Setups Wireless_repeater Wireless_WDS_Mesh CAPsMAN Forum: MikroTik RB751U-2HnD as repeater (preferably with working U) Thank you, but like i said, no "simple" setup guide. I just need to extend my wifi using one router. I was able to setup WDS Mesh but i was not getting any...

ytuxedo002

You have to add it as a package. It's in the download section.

ytuxedo002

I'm trying to do something similar but way simpler. I have a CRS125-24G-1S-2HnD-IN set as my gateway and wireless router. Now i need to extend the wifi of this device further in our office. I have another RB2011UiAS-2HnD-IN which i would like to use for this task. I have tried different WDS settings...

ytuxedo002

I was wondering if anyone had any updated VOIP QOS best practices with the new version of RoS? Currently we are using the "mark TOS" method and just creating Queue Tree entries. This doesn't seem to work real well when users are flooding the networks. Any info is very much appreciated. Tha...

ytuxedo002

I started having this issue a few days ago. Now the dude crashes every few hours. I even built a fresh windows server and imported my data but it still happens on the new server. Any ideas? Log Name: Application Source: Application Error Date: 11/12/2013 3:45:41 PM Event ID: 1000 Task Category: (100...

ytuxedo002

This is now happening to me as well. Did you ever find the cause?

Regards

ytuxedo002

You have the OpenVPN server and client and both have logs. It sounds like you're only looking at the Mikrotik logs; do you have access to the server logs?

Yes i do sorry. the logs don't even show the mikrotik hitting the server.

ytuxedo002

The server logs should provide more detail as to why this is happening. Keep in mind that Mikrotik, inexplicably, still does not support OpenVPN over UDP; you have to use TCP. Thanks. Same thing happens with TCP though. When you say logs, are you speaking of /logs? Because this doesn't tell me anyt...

ytuxedo002

Bump.

Sorry guys, i have no where else to turn.

Thanks

ytuxedo002

Nobody?

ytuxedo002

Guys, I'm having a hell of a time trying to get this to work. I have an Openvpn AS server up and running. I am able to connect to it with the openvpn client without issue on a windows pc. I have exported the user certificates using this guide http://docs.openvpn.net/administration-guide/cli-command-...

ytuxedo002

First go to your vrrp interface and add a comment to it : you can go to tools netwatch press the + sign as host put in your gateway public ip address .. or you can even use some sort of public reachable ip (google dns 8.8.8.8 ? ) and on the down tab put something like :log info "gateway not re...

ytuxedo002

You can make a script that monotors if your isp gateway is reachable and if not disable the vrrp interface untill the gateway is reachable again.

Thanks for the response. that's what i was thinking but i didn't know where to start.

ytuxedo002

I'm setting up two 450G's for a client right now and have them successfully setup using VRRP. Each MT has it's own separate ISP circuit. My questions is how can I get it to failover if one of the two internet circuits go down and not necessarily the Mikrotiks going down? Let me know if I explained c...

ytuxedo002

In mangle, add a routing mark WAN2 for all the traffic !local coming from interface LAN2 add routing mark WAN1 for all the traffic !local coming from interface LAN1 In route, add a route for all the routing mark WAN2 to go through WAN2, and same for WAN1. There are plenty of examples on the wiki Th...

ytuxedo002

We deal a lot with VOIP here and we usually disable the Service ports for SIP. Never had a problem after figuring out that gem.

/ip firewall service-port disable sip

ytuxedo002

Also, i have had an issue when changing the default lan to something different, i get no internet. Found out that i needed to get rid of the static DNS which stays as 192.168.88.1.. Once i remove that i get internet access.

Hope this helps

ytuxedo002

setup: 2 isp's and 2 LAN's I have both ISP's setup on different ports as well as the lan's on different ports. LAN1 has dchp enabled LAN2 does not (as they are connected to same switch). My questions is how can i get LAN2(conf with static ip's) to push traffic through WAN2? right now it only goes th...

ytuxedo002

Here is what is shows

ytuxedo002

Nope. Everything works as expected since RP. Tried on RP x64 Pro and have it working on latest RTM x64 Pro. All versions are genuine.

Kamil

Genuine install straight from MS. 32bit version though. Don't know if that will make a difference.

ytuxedo002

Tried running winbox from a new windows 8 install and nothing. Anyone run into this yet?

Really sux cause I manage a butt load of MT's for my clients.

Thx

ytuxedo002

Hey guys,

I have a certain Ip that is connected to my rb751g. I have already created a firewall rule to drop all packets from that ip but in the connections tab it still says

U xx.xx.xx.xx (src) 224.0.0.1(Dst) 2(igmp)

Anyone know what that ip is trying to do?

Thanks

ytuxedo002

I think the easiest way is with a couple of mangle rules lets assume the following LAN1 is 192.168.1.0/24 LAN2 is 192.168.2.0/24 default gateway of ISP1 is 10.1.0.1 default gateway of ISP2 is 10.2.0.1 you could add a couple of mangle rules to mark the traffic from each LAN chain=prerouting action=m...

ytuxedo002

I think the easiest way is with a couple of mangle rules lets assume the following LAN1 is 192.168.1.0/24 LAN2 is 192.168.2.0/24 default gateway of ISP1 is 10.1.0.1 default gateway of ISP2 is 10.2.0.1 you could add a couple of mangle rules to mark the traffic from each LAN chain=prerouting action=m...

ytuxedo002

OK - so you need to be just a little bit more specific :) Do you want LAN1 & LAN2 to both use WAN1 & WAN2? If so is this on a load sharing or fail-over basis? OR, do you want LAN1 to us WAN1 only, and LAN2 to use WAN2 only? What type of WAN connections are you using DHCP-Client, L2TP, PPPoE...

ytuxedo002

Hey guys,

Been trying to get this to work with some of the suggestions on the forums but I cannot get it to work.

RB751G
Port 1= WAN1
Port 2= LAN1
Port 3= WAN2
Port 4= LAN2
Wifi = Bridged with LAN2

Anybody have specific instructions for this setup?

Any help is greatly appreciated.

Regards

ytuxedo002

Hey guys, I was recently using MT on a pc and everything in the office was working fine. We just switched to an RB751u-2Hnd. Now all our Yealink sip phones work fine but Polycom and Cisco 7960 don't register at all. They both are grabbing config files just fine but wont register. Running v5.15 NAT ...

ytuxedo002

Hey guys, I was recently using MT on a pc and everything in the office was working fine. We just switched to an RB751u-2Hnd. Now all our Yealink sip phones work fine but Polycom and Cisco 7960 don't register at all. They both are grabbing config files just fine but wont register. Running v5.15 NAT ...

ytuxedo002

Hey guys, I was recently using MT on a pc and everything in the office was working fine. We just switched to an RB751u-2Hnd. Now all our Yealink sip phones work fine but Polycom and Cisco 7960 don't register at all. They both are grabbing config files just fine but wont register. Running v5.15 NAT i...

ytuxedo002

If you have an Omnitik mounted around 20ft with laptop 802.11a/n clients, clear line of site, 300ft should work. Indoors is dependent on what materials the building is made of.

Rough estimate, anyway.

Thats what i was looking for. Thank you very much guys. Have a great week.

ytuxedo002

Thank you all for your responses.

I guess i'm looking at this the wrong way. I'm thinking more of wifi clients (laptops and smartphones for example) in the surrounding area rather than an SXT at the other end.

ytuxedo002

We have clients (SXT and Groove + 24dB ant) few kilometers away from Omnitik, no problem.

Not P2P though... strictly as an Access point

ytuxedo002

What is your question exactly?

Sorry. What is the wireless distance I can get out of this device, configured as an access point?

ie: 200m...1500sq ft...etc..

ytuxedo002

Can't seem to find any solid numbers.

Anybody have an answer?

Thank you

As an AP...sorry

ytuxedo002

Can't seem to find any solid numbers.

Anybody have an answer?

Thank you

ytuxedo002

Hey guys, I'm having an issue where my local lan dhcp-server is not handing out ip's. I have a hotspot setup and that interface is handing out ip's just fine. Everything seems to be configured the same. Any help would be great. V5.14 x86 version Nevermind. For some reason there was a relay setup on...

ytuxedo002

Hey guys,

I'm having an issue where my local lan dhcp-server is not handing out ip's. I have a hotspot setup and that interface is handing out ip's just fine. Everything seems to be configured the same. Any help would be great.

V5.14
x86 version

Search found 62 matches