MikroTik

pixelkop

Head office is having Fortigate Firewall with ISP1 and ISP2. branch ofiice having RB750 with two Ipsec tunnel and 2 ipsec policies. vpn is working fine but when isp1 fail isp2 will start then branch should also used second ipsec tunnel and second ipsec policies. how to do failover.

pixelkop

IT WORKS FINE WITH MIKROTIK CLOUDE SETTING

pixelkop

We want do site to site VPN with RB 750 UP with internet USB dongle. USB dongle does not provide fix IP. we have center site which is having Static IP. so can we get help on VPN with site-1 with static IP and site-2 with usb dongle dynamic IP. please help me. thanks in advance

pixelkop

branch 2 # jan/02/1970 00:04:26 by RouterOS 6.15 # software id = IX6K-SGBJ # /interface ethernet set [ find default-name=ether1 ] name=ether1-gateway set [ find default-name=ether2 ] arp=proxy-arp l2mtu=1600 name=\ ether2-master-local set [ find default-name=ether3 ] master-port=ether2-master-local ...

pixelkop

We have connectivity from data center to branch1 with point to point E1 leaseline with CISCO router. from router there is cable to branch1 switch for local network. all perpole are accessing data center server. for another branch we have configured Site to Site VPN from branch1 to branch2 with Rb750...

pixelkop

recently we have purchased 30 mpbs internet braoadband line.. we got port at ISP end . from ISP end we have installed point to point link of SXTSA5 AC pair. link configured with AC setting and bandwidth is 70-80 Mbps. CCQ 86 to 90 %. but we test speed test of internet at other end we get 10 mbps dow...

pixelkop

thank you i will check

pixelkop

sorry for lac of information. we want connectivity between customer A to C and customer B to D

pixelkop

my village is having one hill at both side of hill there are four offices 2 office in one side and 2 office other side. all four customer are different. we are putting 120 sector two no on hill top both are back to back covering both valley. now we are using sxt lite 5 at client. distance from secto...

pixelkop

we are WISP setup. we have given 2 Mbps lease line to customer. tested 2mbps at base station working ok. we installed PTP link of sxt lite5 bridge mode. bandwidth TCP bandwidth is 70 mbps. but at customer end we get 2 mbps download but 1.2 mbps upload. any setting missing or any additional config ne...

pixelkop

what should be best single for best bandwidth. -65 or -75 any standard or experience. VLAN is necessery.

pixelkop

I am using two SXT SA5 AC for 5 km link we need 100 MBPS bandwidth for wisp backhaul link. we are getting 25 to 30 mbps bandwidth. is there special config setting for AC product. Access point config /interface bridge add name=bridge1 protocol-mode=none /interface wireless set [ find default-name=wla...

pixelkop

some customer facing issue of uploading and downloading issue.

pixelkop

we have just started wisp. main isp link RB 750 and from ethernet 2 to base station. on station netmetal 5 with 120 sector 3 no antenna to cover 360 degree. now customer is facing some speed issue. 1. what will be cpe setting any firewall or mangle rules required for CPE ?? 2. CPE signals strength i...

pixelkop

nat rule moved above but still same issue. ARP enable on eth2 port is necessery ??? to talk both lan to each other.

pixelkop

i see connection in installed SA. but no ping from lan to lan.....please help

pixelkop

we have adsl broadband connection with static IP at both location. we configured adsl modem in bridge mode site a:- head office # jan/02/1970 05:40:45 by RouterOS 6.15 # software id = MUHY-Y8VG # /interface ethernet set [ find default-name=ether1 ] name=ether1-gateway set [ find default-name=ether2 ...

pixelkop

i am facing some strange problem when i ping form 192.168.245.66 to x.x.x.90 some time i get request time out. but client connected to this sector ping contionusly this is bridge network. some time i get RTO to x.x.x.51 also reply for 8 time then RTO for 2 times... help me

pixelkop

We have follwing setup netmeatal with 120 sector ip 192.168.245.51 netmetal with 120 sector ip 192.168.245.90 netmetal with 120 sector ip 192.168.245. 91 SXTHG ip 192.168.245.96---------------link--------------------------------SXTHG ip 192.168.245.66 @ ISP from ISP we got intenet at SXT HG. all con...

pixelkop

any one..... can we do OSPF between these two link. ????

pixelkop

one of my customer having MPLS link between datacenter and branch with both end having cisco router recentely we have installed mikrotik SXT link as a standby. now we want to do failove between MPLS and Mikrotik please see attched diagram please help how to do..

pixelkop

export config and post

pixelkop

We are configurating Rb1100 AHX2 as hotspot. ether 1 is wan eth2 local lan and from ether2 one cable is going to 24 port switch of network. no dhcp configured on 1100 hotspot is working ok after some time some node are disconnected from main server. ping also gives request time out. if we remove RB ...

pixelkop

hey...thanks a lots....its working removed nat and changed gateway

pixelkop

Connecting two different branches by PTP link. having two RB750 at both side connected by PTP link and network. Site A:- RB750 /interface bridge add name=bridge1 /interface ethernet set [ find default-name=ether2 ] name=Ether2 /ip address add address=192.168.245.73/24 interface=ether3 network=192.16...

pixelkop

Please find details diagram. please help

pixelkop

We have installed two radio link with basebox 5 . there are four radio. location one R1-192.168.254.102 R3- 192.168.245.71 and location two R2-192.168.254.103, R4-192.168.245.70. at location one we have server having ip 192.168.10.39 . from another location users are accessing this server. we want t...

pixelkop

we have installed 20 km point to point link with netmetal 5 with soild rocket dish of 30 dbi. we are getting -60 db single strength. in mikrotik bandwidth it shows 80 Mbps TCP bandwith. but when we test with ierf tool it gives 3 mbps bandwidth. also simples copying of big files from one location to ...

pixelkop

we have point to Multi point setup . have base station basebox 5 with omni antenna and connected 7 office from 10 to 15 km circle. internal network range is 192.168.1.x for main office and branch office. each radio eth1 having 192.168.245.x . setup is one month old. now we are facing problem some ra...

pixelkop

which antenna you are using ??? which wireless card on rb433. why you are not going for basebox 5 which is 912 with MIMO antenna. what is signal level you are getting ??? LOS is clear ????

pixelkop

nice info thnak you...

pixelkop

I want to cover big campus of student hostel for internet. planing to use basex box 2 with 120 degree sector antenna. putting one at hostel front and one at back of the hostel. front and back having windows so got good coverage during survey. 25 rooms at fron 25 rooms at back each room three student...

pixelkop

We want to create failover for branch office. At HO we have two MPLS connection terminated on two different cisco 1905 router. 1905 having a failover script From Head office we have rocket M5 two link connected back to back for branch office. At Branch office we have only one MPLS connection termina...

pixelkop

This is Ethernet interface lease line..

pixelkop

Can i use RB 750 router instead of CISCO 1905 for 2 MBps internet lease line ? how to config internet lease line on mikrotik ???

pixelkop

Since this rainy seasons started we having facing routerboard and wireless card of radio issue. Can you explain us how to do proper earthing and esd protection technic for mikrotik radios.

pixelkop

Thanks for all reply. now i can do this project very cool.... we are installing 10 radio link for one banking client.

pixelkop

We are suggesting radio link for one Bank. but customer is saying Wireless is not secured. hacking is possible. so can you describe what type of security we are using when we are doing point to point link with router boards. any wiki ??? so we can give to customer. Thanks in advance.

pixelkop

routerboard is 411. connection is
radio ethernet port to Poe port & poe port to switch ethernet port. there is no other cable to switch. still light blink. help me..

pixelkop

when we put cat-6 cable from PoE to switch. switch shows heavy traffic. all lights blink fastely. there is no other connection on switch. we have removed all cables. only one cable from mikrotik PoE to swith is there. who is generating traffice???

Search found 40 matches