MikroTik

interlink

Try this... set wlanX wireless-protocol=nv2 Where wlanX should be replaced by your interface number, then I disabled the nstreme protocol y the nstreme tab in winbox. With this option set on the ap side, only nv2 clients can connect to the AP, yo should also set the distance between the 2 points in ...

interlink

Hi, does anyone seen that the ptroughput is missing when you configure, nv2-nstreme or nv2 only mode?
I´m using two RB600 with Ros v5.7 and SR71-15. Everithing seems to be right but the ptroughput.

interlink

Hi, does anyone knows wich is the limit of maximum concurrent connections, in terms of connections and mbps. I need to NAT thousands of private ip´s, and my cisco ASA 5520 is getting full of connections, actually supports 280000 and is touching the upper limit. My thoughts, is that is only limited b...

interlink

Shure, check this http://www.routerboard.com/pdf/routerbo ... _tests.pdf
Post your configuration or more info and maybe someone can help you.

interlink

I think that Atheros AR5413 must be supported, these cards are deployed everywhere.

interlink

Not available yet, as you can see on ROS 3.22 [xxx@Ric-rtr] > system health [xxx@Ric-rtr] /system health> print fan-mode: auto use-fan: main active-fan: main voltage: 11.9 temperature: 49 [xxx@Ric-rtr] /system health> print oid voltage: .1.3.6.1.4.1.14988.1.1.3.8.0 [xxx@Ric-rtr] /system health>

interlink

I have the same problem, any advance with the solution?...

regards

interlink

I just get server dude server running on linux, but now the thing is that I can´t get the dude server listen on port 80 or any other port that give me web access (no apache running or any other web server). Just access the server with dude client. Anyone else with this issue too?. Is there any param...

interlink

Does this unit work as a switch like the old RB 192?.

interlink

It will be usefull for me to have a tftp server to provide cm configuracion files.

interlink

I succesfully upgraded the firmware to v 2.13 and the random reboots totally disapear. But now I have two minor issues. In winbox appears to be disabled enable polling and disable CSMA also framer policy and framer limit too, this is only on winbox, in the console everything is ok. The other issue i...

interlink

For all the MT guys. Please give us (your customers) an official explanation of this issue and provide us a solution RMA, software upgrade, or whatever you want to solve this problem, Don´t make it public if you want provide us a response via mail, most of us have open trouble ticket on your support...

interlink

Now ROS v3.5 is released, must we try it, or is pointless...?

interlink

To MT support guys, is there any news with this trouble, are you working on a solution??.
Just to stay informed, don´t want to disturb

interlink

Who says that rb600 has a voltage monitor. AFAIK the only one is rb333.

regards

interlink

The stablest ROS version for me was 3.0, this one give me 1 day and a few hours uptime. Just for testing I invert the wlan mode now the unit that constantly reboots it is a station-wds, before that it was the ap-bridge. I will keep you informed guys! No success with this change, the unit keep reboo...

interlink

The stablest ROS version for me was 3.0, this one give me 1 day and a few hours uptime.
Just for testing I invert the wlan mode now the unit that constantly reboots it is a station-wds, before that it was the ap-bridge. I will keep you informed guys!

regards.

interlink

The same for me, i didn´t upgrade to 3.4, just using 3.3 with the same problem, but when the unit reboot autosupout.rif is not generated. My watchdog conf is very common. watch-address: none watchdog-timer: yes no-ping-delay: 5m automatic-supout: yes auto-send-supout: no send-email-to: send-email-fr...

interlink

You can see voltage on RB333 only from console. [xx@xx] > system health [xx@xx] /system health> print fan-mode: manual use-fan: main active-fan: main voltage: 27.1 For graphing purposes you can use mrtg and this linux script, or the dude with the oid. #!/bin/sh SW="/usr/bin/snmpwalk" uADDR...

interlink

I think temp monitor is only available on rb230, because is the only one rb that haves a temperature sensor.

interlink

Yes, it will be very nice if someone of the mikrotik staff could clarify this parameters settings.
We use mikrotik mostly in ptp link and this seems to be important for this type of configuration.

interlink

I suffered this issue too, random reboots, kernel panic...
Is this officially recogniced by mikrotik??, is there any solution on the way for this??.
We have deployed various of this cards, so we can´t just give up on them.

interlink

Connect directly your pc nic to the ether of the rb133c and use winbox to access via mac address, this can be done using the button with three dots on the right side of the address box.
Another method is to connect via serial port 8n1,
Default user is allways admin, and no password.

hope this help.

interlink

Just downgraded to v3.0 and now have 2 hours uptime kicking 36mbps without problems and no reboots, same config and same hardware. Now I´m going to test in turbo mode.
Maybe the problem is a bug in v3.2.

interlink

Does anyone have seen this error on a RB600??. I have a ptp link testing in the lab with this configuration: Unit A 0 name="wlan1" mtu=1500 mac-address=xx:xx:xx:xx:xx:xx arp=enabled interface-type=Atheros AR5213 mode=ap-bridge ssid="xx" frequency=5825 band=5ghz scan-list=default ...

interlink

Because, I dont have the watchdog activated, so the auto supout was not generated.
If the RB333 hang up again I´ll send you the file, or if you want I can generate the file and send to you.

Many thanks normis.

interlink

Im geting this error frequently. system,error,critical System rebooted because of kernel failure. Is there any possibilty to be related to a hardware failure?. I can´t provide the supout.rif for now. Configuration & hardware. Rb 333 Wlan ubiquiti SR5 Power suply 28v 1A. Ap_bridge --> station wds...

interlink

The same happens to me. The error, can´t load roteros.dll, using mac I get this error, using ip address works fine.

interlink

This would be a good feature, if supported. In our case, we have a bgp session between us and our providers, and a wireless link (rb532/sr5) in the middle, so we can´t do static routing in case of nstreme2, because we lose redundancy, and all the static routes will be impossible to manage. With brid...

interlink

Me too please.
emiliano<at>cablenet<dot>com<dot>ar

tnx

interlink

I have the same problem but when de pigtail is installed in short circuit at the wlan, so the only way to get the wlan back was resetting to default.

interlink

Covering the back side of the sector with a metalic mesh should work fine too. But the separation is the best solution.

interlink

Hi, I have the same issue, with a 22km link usig rb532a, atheros SR5, when I upgrade to version 2.9.40 an compression was enabled the link stay up for 50 seconds top and then disconnects for a few seconds and go up again.
If I uncheck compression option the link stay stable and works find and stable.

interlink

So..when the support of new snmp features will be ready to try?

interlink

I have checked the config and yes, was my mistake, when import the config from another rb the mac was changed.
Thanks for the answers.

interlink

I think I have very bad luck, recently we buy two new rb532a and setup a ptp link one of them installed near another rb532a connected on the same switch on the same vlan, wirelessly everything works fine, but when ping the remote extreme we get no answer, after a few hours of investigation we indent...

interlink

I'm thinking to use a routerboard 532 overclocked at 333mhz, to get better performance. I will post the results soon.

interlink

I'm planning to set up a wireless link with 2 RB532 at a distance of 31km using dual nstreme wtith SR5, and dual polarized antennas transmitting on 5.180-5.320 range and receiving on 5.745-5825 range. Anyone knows what performance could I get, o someone has done this with this configuration. I'll pr...

interlink

Please support it...

interlink

The issues comes with no rain, and it´s a sporadic problem, not always happen, the cables are good and connectors too. Maybe it is an interference of another link, when the propagation conditions are excellent. Opinions?

best regards friends.[/img]

interlink

The frequency is set at 5825 mhz and nstreme is enabled and polling is enabled too.
Any other suggestion will be great...

interlink

But this not happens all the time, just sometimes when signal fall down, I have scanned the spectrum and nothing appears to be transmitting in this frequency. Can be periodic calibration o some parameters the responsable.

interlink

This is an extract from the log, I hope it helps. sep/14 22:01:53 wireless,info 00:15:6D:xx:xx:xx@wlan1: disconnected, extensive data loss sep/14 22:01:53 wireless,debug wlan1: removed dynamic WDS link 00:15:6D:xx:xx:xx, name sep/14 22:01:55 wireless,debug wlan1: 00:15:6D:xx:xx:xx attempts to connec...

interlink

I have a ptp link at 30 km with 2 rd532+sr5, and two 1.2 m dishes. Configured as ap-bridge and station wds to bridge all the traffic. The average signal of this link is -60 dbm, but when the signal comes to 73 I´ve got this message in log wireless info "wlan1:00:15:6D:xx:xx:xx, sent deauth"...

interlink

Read this, I think it´s wat you need.
http://wiki.mikrotik.com/wiki/Load_Bala ... e_Gateways

interlink

Hi, does anyone knows if linksys WAP11 work as a client of a mikrotik AP 2.4ghz?.
Because I can see de AP but can´t get traffic between them.

interlink

It would be nice to have OID´s for noise floor, Signal to noise and Tx/Rx CCQ.

Search found 47 matches

Re: Nv2 802.11n not reporting Ptroughput

Nv2 802.11n not reporting Ptroughput

Firewall max concurrent connections

Re: can 433 board support 2 mbps load

Re: How to use integrated Spectrum Analyzer?

Re: RB450G is here!

Re: RouterOS + Dude Web Interface problems...

Re: dude-3.1 under wine-1.1.5 = LocalMedium: postpone read

Re: RB493

Re: Feature Request : TFTP server

Re: Rb600 reboot fix

Re: rb600 make reboot every day

Re: rb600 make reboot every day

Re: rb600 make reboot every day

Re: Why RB600 don´t have a Voltage Monitor?

Re: rb600 make reboot every day

Re: rb600 make reboot every day

Re: rb600 make reboot every day

Re: Temp graphing?

Re: Temp graphing?

Re: v3 Bridge Port Settings

Re: rb333 kernel panic

Re: 133c Prblem

Re: RB 600 reboots with kernel fail

RB 600 reboots with kernel fail

Re: kernel failure on ROS v 3.0

kernel failure on ROS v 3.0

Re: Mac Winbox on rc11

Re: RB333 w/RC4 and WDS

Re: CPE-Antenna alignment via customer / Application available?

Re: Wireless Interface disappears!

Re: Antenna RF shielding

check config

Two Rb532a with same MAC??

Nstreme dual with RB532. Performance??

SR5 sent deauth

Linksys wap11 compatibility

RF OID