Thank you!

hello,


I need older versions of the router, 6.25 or 6.27 to see if my problem with DNS (http://forum.mikrotik.com/viewtopic.php ... 61#p513697) appears in an older version.

thanks

Not quite sure if this is new with 6.33.3 but pretty often the webfig becomes unresponsive and does not react on any clicks anymore. An F5 reload fixes it for a bit until it fails again within a few minutes. I have noticed the same. Before in version 6.32.x I didn't have this issue. I'm using Firef...

hi, On CCR1009 i observed at system health / fan speed (in winbox) although the main fan works shows zero speed or rate freeze on some value. And when CCR1009 router receives a greater load (example: transport more data) when the fan is correctly updated. that may be the problem? Does a bug? thanks

this is a temporary solution until they fix the bug ? or always use dns statically ? Always. It's not a bug. Router reboots, gives out IPs via DHCP, and only after that he learns DNSs via PPPoE. DHCP Server cannot force clients to renew DHCP leases, AFAIR Chupaka, permit me to note : on RB1100AHx2 ...

use router's DNS for customers or set DNS IPs in DHCP Network statically

this is a temporary solution until they fix the bug ?
or always use dns statically ?

thanks

please permit me to review my problem: my problem is: after reboot the router CCR1009 (RouterOS 6.33.3), although receive 2 x DNSv4 via PPPoEv4, these DNSv4 are not distributed on the computers in the LAN, computers in LAN receive IPv4, maskv4, default gatewayv4, but not DNSv4, I noticed that i rece...

I have a RouterOS 6.33.3 on CCR1009 and notes that although they do receive 2 ip DNS via PPPoE , <<<<<dhcp server distribute the dns when giving reboot rooter>>>>. until i stop and restart the computer ethernet interface only then takes dns. I think that the DHCP server bind IP + gateway earlier tha...

anyone who now if at his moment , exists pppoev6 on pppoev4 session ?

thanks

i have one private subnet 10.1.1.128 /27 .

addresses 10.1.1.130-10.1.1.134 out through one NAT1 they have out interface pppoe1
and
addresses 10.1.1.135-10.1.1.140 out through another NAT2 they have out interface pppoe2

it is possibly to resolve this problem? and how?

thanks

There are no switch chips in the CCR.

so can not be grouped in groups of switch ports?

Does anyone know how many switch-chips are CCR1016-12G BU?
somehow ONLY has a chip swich?

how many groups can group switch 12 gigabit ports?

Can you give me a link with information about these issues (switch-chip group ports at CCR1016-12G-BU)?

thanks

thanks

I do not know if any of the Mikrotik routers has Hardware NAT, but a few models are fast enough for 1000Mbps.

I would advice the RB1100AHx2 because this one is for sure fast enough and at this moment very afordable.
Or else the Tilera CPU routers (CCR series) are for sure fast enough.

hello

Recently my provider offers bandwidth of 1Gbps Internet access(PPPoE) and would like to know if any model has MikroTik router that has hardware NAT (not software NAT )

because i have rb450g (I only have 200 mbps of the provider gave 1000Mbps )

thanks

Hello , I want to know if is any RouterBoard model with 3 switch chips?

thanks

In RouterOS v6, will it now has fully-functional DHCPv6 instead of the DHCPv6-PD that is available in RouterOS v5?

there's no one answer if it is available to us in full DHCPv6 routerOSv6?

I was asked to send supout.rif to correct some bugs.
I'm in router configuration stored passwords and users. how safe is to send this information to suport@mikrotik.com?

I wish to inform you of these bugs in this versions of the routerOS: (RB450G) 1. When you access PPPoE Scan after displays MAC addresses available, drop the PPPoE connection and then reconnects but stay connected than 0/1 second and then disconnects and reconnects again. From this loop connection - ...

Hello, I would like to know if at this point there is a version of routerOS that supports PPPoE/v6. Provider gives me dual stack when connect with PPPoE , offer one IPv4 and one IPv6 address on the same PPPoE session and not get IPv6 address.

Well i found a solution. Its titan pc case single slot cooler. It blows air into routerboard and cools all system. Just use 12V adapter (from switch or something). Air goes out from lan ports and other side holes. Screws fits perfectly. It just get bigger and noisier and cool. And needs 2 electrici...

some more intersting info This router is so important, I cant even down it for a minute and we get in trouble with the banks voip, waiting in christmas to replace it sometime :-) just noticed this now on the 450g, cpu peaks to 100% easily at times, pushes around 3M of g729 voip thru with around 30M...

If it is a 450G you have the 8316 switch chip which has its own VLAN header functions - see the following link: http://wiki.mikrotik.com/wiki/Manual:Switch_Chip_Features I read the article but does not say whether the port eth1 can be master for eth2 and eth3. When setting the port eth1 as master f...

hi , it is posible this configurationon RB450G?

eth1-master port of switch |
eth2-slave port of eth1 master | -----|
eth3-slave port of eth1 master |
eth4-none -----------------------|
eth5-none -----------------------|

please help me with a solution of code .
thanks

eth1<(in) vlan native(untagged)+vlan100(tagged) eth2>(out) vlan native(untagged) eth3>(out) vlan native(untagged) eth4>(out) vlan 100 (tagged) eth5>(out) vlan 100 (tagged thanks It can be solved with the switching chip configuration or bridging interfaces. Do you need wire speed switching? Do you n...

Hi, MikroTik router can separate a tagged VLAN to another VLAN untagged? more precisely on eth1 enter a vlan vlan tagged and an untagged on eth2 and eth3 should be removed and the untagged VLAN ports and eth5 eth4 should be removed VLAN tagged. can someone help me with configuration? eth1<(in) vlan ...