MikroTik

Test471

I've tried that but, as I said, holding down reset button does nothing except flashing SFP led a few times and then reset again. You must carefully read the instructions on how long to press the button. I did. I've tried to hold it until SFP starts flashing fast (this is the only LED that shows som...

Test471

I've tried that but, as I said, holding down reset button does nothing except flashing SFP led a few times and then reset again.

My computer says "cable unplugged" all the time. I've tried with connecting it to eth1. Any other suggestion?

Test471

Hello I just upgraded my hap ac via webfig to this version and it is dead since then. There is no beep and by looking at LEDs it looks like it keeps restarting after 10 seconds. I've tried to do restart by holding the button but the only thing that happens is that SFP LED starts blinking and nothing...

Test471

Just click on "Time" column and you will have it sorted in descending order...

Test471

Point it to some private address and configure firewall to reject.

Test471

Test results in both directions... From client to router: PING 10.2.1.1 (10.2.1.1): 56 data bytes 64 bytes from 10.2.1.1: icmp_seq=0 ttl=64 time=2.912 ms 64 bytes from 10.2.1.1: icmp_seq=1 ttl=64 time=1.765 ms 64 bytes from 10.2.1.1: icmp_seq=2 ttl=64 time=1.170 ms 64 bytes from 10.2.1.1: icmp_seq=3...

Test471

Well, this is brand new device. No fw or mangle rules. No load on device (only devices used for testing). I've done some more testing this morning and bridge is only thing that makes problem. So if anyone has some idea of how to configure bridge in order to work properly...? As i said, I tried every...

Test471

Hello, I have a problem with hap ac. When wlan interface works as stand alone interface (without bridge) then everything works fine. Problem is when wlan gets connected as bridge port. Then is situation as follows: - ping from client to router is ~1ms - ping from router to client is somewhere betwee...

Test471

I installed 6.36 and now I have a problem with EoIP/IPSec. The thing is that if I change local address on EoIP interface (manually or via script) it does not update IPSec policy but leaves the old address. This was working before 6.36. I tried to delete EoIP and create new one but problem is still ...

Test471

I installed 6.36 and now I have a problem with EoIP/IPSec. The thing is that if I change local address on EoIP interface (manually or via script) it does not update IPSec policy but leaves the old address. This was working before 6.36. I tried to delete EoIP and create new one but problem is still t...

Test471

I have EoIP/IpSEC and it says I must fill local address.

Now I solved this problem by writing script which is checking every 15 secs if local address changed and makes update but with this new update I dont see any way of going without it.

Test471

MikroTik RouterOS v6.36rc4 is released.

*) tunnel - added option to auto detect tunnel local-address;

How exactly this works?

Test471

Good afternoon, I think it would be really nice if CAPsMAN could be used to configure entire CAP and not just wireless interfaces. At least ethernet and VLAN. Many times I have situation that I connect CAP and it gets configured from CAPsMAN in a second and then I have to connect to it in order to c...

Test471

Anybody? In the meantime I tried to do packet marking and input/output packets are still being ignored by simple queues when I have target address router IP. On the other hand those packets are handled ok by queue tree but I would preffer to stay with simple queues. I forgot to mention I am using 35...

Test471

I have two locations connected with IPSec/EoIP. I wanted to enable simple queue in order to shape traffic between. Local router has subnet: 10.2.0.0/16 (Router IP: 10.2.99.1) Remote router: 10.1.0.0/16 (Router IP: 10.1.99.1) When I put on local router simpe queue rule with target: 10.2.0.0/16 and Ds...

Test471

Background scan does not work via Webfig.

When I try it from Webfig it disconnects clients but when I try the same thing from winbox then it works.

Latest rep package on 951g.

Test471

Hi, I have one wlan (not CAP but stand alone config) and in access list defined which device should have which VLAN tagged. Everything works fine except that devices on same VLAN cannot communicate between themselves when registered to same wlan. Communication is ok for example between devices on sa...

Test471

I've sent config to you the same day you asked for it. In the meantime I did some testing and it looks like that clients are disconnecting fast when dhcp gives them very short lease. When DHCP is giving 60 seconds lease to clients then they are disconnecting. Now i changed it to 24h and they are not...

Test471

- disconnected, received disassoc: sending station leaving (8) This is wireless client decision to disconnect from the AP. We don't have any control why they want to connect. WMM PowerSave feature is always enabled in the CAPsMAN and can't be disabled. Ok, now I am pretty sure there is some problem...

Test471

We don't have any control why they want to connect.

I guess you missed something. I said everything was working fine before CAPsMAN. In the meantime I tried some of those devices on another AP without CAPsMAN and it is working without disconnect.

How is that?

Test471

Ok, but then, why are clients keep disconnecting after they go to sleep mode? As I said, I am looking at registration table on CAPsMAN and not a single client is registered for more than 3-5 minutes (except laptops): - disconnected, received disassoc: sending station leaving (8) All devices are runn...

Test471

Are we going to get WMM support in CAPsMAN any time soon? What's new in 6.30 (2015-Jul-08 09:07): *) wireless - added WMM power save suport for mobile devices; Yes, but how do you turn it on on CAPsMAN configuration? I had 3 stand-alone APs working fine when I enable WMM on their interfaces but yes...

Test471

Are we going to get WMM support in CAPsMAN any time soon?

Test471

Could someone from MT please fix this issue? So, to remind you: CAPsMAN datapath config: Bridge, bridge cost and bridge horizon: empty; Local forwarding: yes Client to client forwarding: yes Vlan mode: use tag VLAN id: 998 CAP is configured to fw all traffic to bridge. On that bridge there is VLAN i...

Test471

Anyone?

In the meantime I tried with other devices also on 6.20 and problem is there also so I am pretty sure it is not me

Test471

I support August google.

Whatever

Test471

Don't get me wrong but I think google translate is not good for this kind of communication

Test471

How many total sector writes? I had same problem with rb951 which was rebooting every few hours and in log there was no reason except that it was rebooted by watchdog. In case I disable watchdog board just hung and then I needed to cut the power off. Tried everything and nothing helped. The only thi...

Test471

^ I can confirm this. When not doing local forwarding and using vlan tagging lease is being offered but client is not responding to that (at least that is what log shows, maybe client is responding but dhcp do not get that response). This is only happening when vlan tag is used. Without it it works ...

Test471

Yes, it is enabled but even then they cannot communicate between each other if local forwarding is also enabled. Only with local forwarding off it works.

Test471

Anyone?

Test471

Hello, I think there is a problem with client to client forwarding on CAP when local forwarding is enabled. When I enable local forwarding then ping between devices on same SSID is not working. Everything else is working: - ping from wireless device to router is ok - ping from router to wireless dev...

Test471

Check out the access list within CAPsMAN. Based on MAC or MAC filter you can assign different VLANs. This is not exactly what you are looking for but maybe there is something that can be done based od radius reply. Just thinking...

Test471

http://forum.mikrotik.com/viewtopic.php?f=1&t=85972

Test471

If your problem are related to OpenVPN and UDP use:

RouterOS actually do not support OpenVPN link by UDP.

I don't know what to say except that you missed the point. Read again

Test471

https://forums.openvpn.net/topic15760.html I have same problem (ros 6.14, iOS 7.1.1). Guys on OpenVPN forum think it is a iOS app problem but I think is maybe something MT guys should check because absolutely same configuration with CentOS instead of Mikrotik works fine. Any ideas? Note: Tried same ...

Test471

Oh, is that so? In that case I understand the purpose of "ip cloud" feature. I was just thinking that MT target group are people with significant IT education/experience. My mistake :) we have many great home access points, and quickset + default config makes it easy for people to use the...

Test471

http://wiki.mikrotik.com/wiki/Dynamic_DNS_Update_Script_for_dynDNS The easy way :) Wasted 2 minutes to register free domain on ChangeIP (or DynDNS) and have "A record" I can remember. Easy for you. For other people, they don't even know such scipting menu exists :) Oh, is that so? In that...

Test471

If I have my own doman than I would not need this useless feature since I would then have script which would check for IP changes and update my domain records. Good luck scripting this your own way. http://wiki.mikrotik.com/wiki/Dynamic_DNS_Update_Script_for_dynDNS The easy way :) Wasted 2 minutes ...

Test471

Some good changes here, including the new "ip cloud" menu What exactly is the point of "ip cloud" when you cannot remember your dns name? If you have your own domain, just create cname records that point to your serial number dynamic dns records hosted by mikrotik. If I have my ...

Test471

Some good changes here, including the new "ip cloud" menu

What exactly is the point of "ip cloud" when you cannot remember your dns name?

Test471

+1

UDP!

Test471

I was trying to find options to set up interworking but it is nowhere to be found. Is it going to be implemented or I am not looking at right place?

Test471

we hope we will be able to fix it soon.

Wow, that was fast

v6.14rc3 does not have this bug.

Test471

Ok, thank you!

Test471

Ok, still doing some testing when VLAN is on top of bridge... As I said in my previous message, client keeps reconnecting with message in ROS log "extensive data loss". Before "extensive data loss" occurs log is saying this regarding communication with DHCP: ...dhcp received disc...

Test471

Ok, now I am 100% sure this problem depends on VLAN implementation. If I do not use VLAN tag in CAP interface configuration and leave it to connect CAP interface on bridge locally than everything works fine. After I enable vlan tagging on CAP interface and put VLAN interface on top of local bridge i...

Test471

If you add a vlan interface to the bridge ports you must leave the dhcp server on the bridge interface and not on one of the bridge ports. No, I did not add VLAN as bridge port. I created VLAN interface which has bridge as it's interface. That's why I put dhcp on VLAN. Point is: - on one CAP I want...

Test471

Sorry, I forgot to mention it was with v6.13. After that I tried with setting interface to local forwarding mode. CAP device was set to add any intrface to local bridge. When I add IP and DHCP server on that local bridge everything works fine. But, when I add VLAN interface to that bridge and move I...

Test471

I have a problem with cap interface if I enable VLAN. VLAN mode = use tag VLAN ID = 111 Than I create VLAN interface with VLAN ID = 111 on cap interface. After that dhcp cannot assign address on VLAN interface. It keeps saying "offering lease without success" in log. If I set VLAN mode = n...

Test471

What's new in CAPsMAN 6.12?

Test471

Exactly the same situation here only with Apple devices.

Test471

I had two RB951-2n and both of them had problem with wireless adapter. It works for a 30-60 mins as usual and then ping starts to be extremly volatile and eventually connection drops. In the log it says something like this "...connection dropped, extensive data loss...". After that, it no ...

Search found 53 matches