Dear Mikrotik forum, I had a strange issue I would like to share with you. Well, I have a PTP link with RB435G and Compex Atheros AR9220 MINI PCIs. both nodes have a basic configuration as Bridge1 between Ether1 and Wlan1. Bridge IP is 192.168.1.1/24 in the first node and 192.168.1.2/24 in the secon...

That is not possible. You can choose just one RF mode. Your wireless card will work as an AP or as a Station but not both at the same time.

I guess, you could choose channel 3 or 4. Also you can reduce the channel width but it depends of your needs.

Dear Mikrotik forum, have someone of you tested NV2 and bonding together? Currently, I have 2 RB435G with 2 Mini PCIs each one. Everything works fine when I configure NV2 and bonding, but when I enable ARP link monitoring I can not ping one Mikrotik from the other one. I mean there is not connectivi...

Thanks for your answer. At least, I know Router OS does not support this kind of Mini PCIs right now.

Dear have you tested some of these Mini PCIs? Thanks.

Dear Mikrotik Forum,
do you know if Mikrotik is compatible with some 802.11ac Mini PCI?. It seems interesting not because of channel width but cause of 256QAM modulation. I checked some old post but I did not find it. Thanks a lot.

Hi again. PC belongs to vlan 2 and all devices have only one IP address (PC, switch, and Mikrotik). PC can ping IP address of switch vlan 2 and IP address of Mikrotik's vlan 2. Regarding to my configuration, I only created vlan 2 and I assigned IP addres to this vlan 2 on Mikrotik. Good luck.

Hi. I have tested this scenario and it works. PC-------switch (HP)---------Mikrotik (RB435G) PC is connected to a switch through an untagged port. Switch is connected to Mikrotik via a trunk port. Mikrotik is connected to swith through a tagged port. PC is in vlan 2. Switch trunk port is tagged on v...

Thanks. I believe I understood.

Hi, maybe this link can help you. I agree with you about Mikrotik multicast Wiki. I forgot, the link is http://forum.mikrotik.com/viewtopic.php?f=1&t=19359
Bye. If you success please tell me.

Hi man. You should first look information on Internet. You can use any terminal software as Hyperterminal or Putty.

Please, I need some help. Thanks.

Dear Mikrotik Forum, I am confused about Nstreme, so I would like you answer my doubt. What the difference is when I set my wireless card as: 1. "interface wireless set wireless-protocol=nstreme 0" 2. "interface wireless nstreme set enable-nstreme=yes 0" Both command lines do the...

Hello, someone can suggest any idea?

Dear Friends, I have the next scenario: 10.10.10.0/24--------R1-------------R2-----------20.20.20.0/24. The link between R1 and R2 is through Ether1 in both routers. Ether1 has two vlans: Vlan10 and Vlan20 in both routers. Vlan 10 is 30.30.30.0/24 and Vlan 20 is 40.40.40.0/24. 10.10.10.0/24--------R...

Dear,
i do not understand your question at all but you can use SCANNER, FREQUENCY USAGE and WIRELESS SNOOPER tools for this purpose. All of them are in the wireless tab.

Dear, It is easy. first use MK PoE and power OmniTik via its Ethernet 1. Then connect your computer and using Winbox choose the Access Point Bridge wireless Mode (choose SSID, Frecuency, Protocol, etc). in SXT device you must do the same but the difference is that you must choose a client mode (Stat...

Dear,
According to datasheet you can get maximum 200Mbps real throughput. you got 20M bytes per second which is 20x8Mbps = 160Mbps; therefore, I believe you links is ok.

Hi,
You can measure the bandwidth using JPERF software.

Dear Xentra, Groove 2Hn has license level 3 so setting up the device as access point for point to multipoint scenario is not possible. However, you can set up the device as access point only for point to point scenario in which it only will accept one client or station. For building up a point to po...

Thanks for your suggestions. I will contact MikroTik support ASAP.

Dear friends, I have a problem that I would like to share with you. First, as you know when there is a RouterOS problem in Mikrotik boards we can use Netinstall for reinstalling RouterOS and the License is kept. I have a x86 board with license and RouterOS is corrupted (I can not access the board vi...

Thanks a lot, I will take that into consideration.

hello falks, I have a problem that I would like to discuss with you. I have a RB800 and 2 RB435G and a pair of RBGPOE. 1. When I power RB800 or RB435G via RBGPOE (Ether 1 port) the association rate with my computer is 100Mbps. 2. when I power routerboards with RBGPOE and I connect my computer to Eth...