MikroTik

mainTAP

Thanks @mainTAP ! Can you pls add if you are using WPA3? Also do you see lots of other neighbors APs ? Both WPA3 and WPA2 are enabled, there are no neighbor's AP at 5ghz in sight and one 2ghz far at -87dbm, but I also have Chateau LTE18 ax at different channels, which is also experiencing the same ...

mainTAP

Sry. but not very useful, pls. give some details: ROS Version ? Config? Chipset in client?

AX2 running the beta5, default config, the client is using AX211
After downgrading to 7.14.3, the client's uptime is 21hours

mainTAP

For me the 2ghz seems even worse than 5ghz : 2024-11-20 15:13:24 wireless,info 8C:17:59:xx:xx:xx@5ghz disconnected, connection lost, signal strength -54 2024-11-20 15:13:25 wireless,info 8C:17:59:xx:xx:xx@2ghz connected, signal strength -46 2024-11-20 15:16:31 wireless,info 8C:17:59:xx:xx:xx@2ghz di...

mainTAP

Updated the AX2 to the beta5 but the issue is still present. 2024-11-20 14:29:20 wireless,info 8C:17:59:xx:xx:xx@5ghz disconnected, not responding, signal strength -53 2024-11-20 14:29:28 wireless,info 8C:17:59:xx:xx:xx@5ghz connected, signal strength -53 2024-11-20 14:29:44 wireless,info 8C:17:59:x...

mainTAP

I am also experiencing this issue on AX2 and Chateau LTE18 ax both running 7.16.1 and it's quite frustrating.

mainTAP

VRF support for Wireguard would be very appreciated.

mainTAP

Hello, have you managed to resolve your situation? Unfortunately, I don't think the DNS via VRF works in Mikrotik, it seems it sends and receives the DNS requests but it's not registered by the DNS service likely as it came from a different VRF.

mainTAP

Got reply from mikrotik support : thank you, but that doesn't seem to be related to the issue in this thread. I got a suggestion from mikrotik to change interface queue types and sizes and observe how it affects the issue: But unfortunately I don't have time to experiment with this right now, so if...

mainTAP

Perhaps this is a cosmetic issue or have you all actually seen performance hits as a result?

I am definitely getting a few seconds outage.

mainTAP

I think I might be getting closer ... Other several days with no Winbox connected = no flaps. A few days with Winbox connected, but showing only the interface table = no flaps and graphs look ok. As soon as I add DHCP server / lease table = gaps started to appear on graphs immediately and all ports ...

mainTAP

Well, now I'm getting quite convinced it has something to do with Winbox as I haven't used it since the last flaps 3 days ago and just had all the ports flapped again after around 40minutes having Winbox connected. I've also checked the graphs and yes they also have those gaps : https://i.imgur.com/...

mainTAP

I haven't checked the graphs, just the values in the interface window. Currently, it's showing normally but this issue is also sporadic. But I am quite sure my graphs will look similar as it matches what I was seeing in the interface table. I am also most of the time connected to the device via Winb...

mainTAP

I don't think it is related to the vlans. Due to its sporadic nature, it's tricky to correlate it with something, but I have a feeling that it might be even potentially related to Winbox connection . Every time the ports flapped, I was connected to the router with Winbox and amongst other things had...

mainTAP

I also use VLANS , but not in such configuration, there is just one bridge ( with VLAN filtering ) for the ethernet ports themselves with no vlan_interface attached to the bridge. I don't think you should add the VLAN interface to the bridge ( https://help.mikrotik.com/docs/display/ROS/Bridge#Bridge...

mainTAP

Hello, All the connected ports on my RB5009 running 7.1.1 are flapping a few times a day. They all go down together and come back up after 5 seconds. All the ports are connected to different devices and there is nothing in the logs indicating what could be happening : 21:47:46 interface,info ether1 ...

mainTAP

Thank you, why would routes exchanged by BGP work and static ones not ?

mainTAP

The multi VRF support would be great.

Has anyone successfully accessed the management from a different VRF using the route leaking workaround ?

mainTAP

Hi, A static route to a different VRF doesn't seem to work when pointing to local IP. I'm trying to reach the loopback 10.0.0.1 which is in vrf2 from the main vrf, but there is no response : [admin@MikroTik] > ping 10.0.0.1 vrf=main SEQ HOST SIZE TTL TIME STATUS 0 10.0.0.1 timeout 1 10.0.0.1 timeout...

mainTAP

The router is used as a portable travel router, the wifi link serves as a backup when the ethernet connection is disconnected and the router is moved around.

mainTAP

Hello, I've got hAP lite ac running v6.49.2 with Ethernet and Wireless connection to the same router running DHCP. I've set the Wireless interface to increase the distance of the inserted default route but it doesn't seem to work properly ( both routes seem to be pointing to the ethernet, the traffi...

mainTAP

Hello, I'm having issues with changing MSS for traffic going to an IPsec VPN tunnel. Looking at packet captures, the MSS change works fine when the traffic is excluded from the tunnel, but when it is included, the MSS doesn't seem to change. I've tried both forward and postrouting chains for the cha...

mainTAP

OnePlusX has also the same issue with mikrotik.

Sent from my ONE E1003 using Tapatalk

mainTAP

Dear Team, Unfortunately after upgrading RB951G-2HnD to 6.34.4 my IPsec/L2TP from Android clients is not working. Downgrading back to 6.32.4 solves the issue, but even upgrading to the latest 6.35rc45 is not working. The connection just time-outs and does not give any particular error. It seems that...

mainTAP

Hi all,

Justo to report that after upgrading RB951G-2HnD to 6.34.3 , IPsec/L2TP VPN stopped working .

mainTAP

Hi there, Can you please advise if it's possible to change the order of ingress/egress VLAN translations on Cloud Router Switch ? Currently I am using RouterOS v.6.27 and Winbox 3.0rc12 and to change the order it seems I have to delete the translations and add them in the intended order. It would be...

mainTAP

Hey SwagLord, Thanks for your response, Well that's actually the setup which was causing issues : all three interfaces added to the bridge -> traffic was blocked after a while for a period of time. If it did not work at all, fair enough. But this seems to me as a bug rather than anything else ;) I w...

mainTAP

What is your phase2 proposal on both ends ?

mainTAP

You'll have to configure your serial port for baud 115200, 8N1.

Thank you Sparkling , this worked .

mainTAP

That example is a bit confusing, how does the switch in the middle knows what ports are assigned to what service-vlan ? I also tried adding a port to egress-vlan-tag to attach the service tag, but nothing was attached : /interface ethernet switch egress-vlan-tag add tagged-ports=ether9 vlan-id=400 a...

mainTAP

Dear All, Can somebody please advise how the egress VLAN tag works when the switch is in service-vid bridge mode ? As I cannot see any difference in frames captured leaving the interface if I enable / disable the following : (none of the tags have changes) /interface ethernet switch egress-vlan-tag ...

mainTAP

I can confirm there is a bug with egress-vlan-translations if you try to assign a customer-tag as a new service tag, it does what it suppose to but then you cannot change it back ( it changes the config but doesn't work ). One then have to remove the rule and create a new one to make it work. But, y...

mainTAP

Am I right if I say that : When I assign a port to a vlan : /interface ethernet switch vlan add ports=ether1 vlan-id=200 learn=yes 1) It should tag the incoming traffic with this tag ( in case of customer bridge mode, it should use the customer vlan (.1q) tags , and if service bridge is used, it sho...

mainTAP

It terms of vlan tag modification / removing , it looks CRS treats .1q tags just as if there was just one and if you send stacked .1q tags to the interface you can modify / remove the outer .1q tag , also you can put an extra .1ad tag on the top. as the frames leave a port, you can do the same , mod...

mainTAP

Hi there, Can you please advise how the vlan port assignment work in case you set the Cloud Router Switch in service vlan bride mode ? /interface ethernet switch set bridge-type=service-vid-used-as-lookup-vid In case of standard customer vlan bride mode, the vlan assignments dictate what port belong...

mainTAP

+1

More information and documentation on QinQ for Cloud Router Switches would be more than welcome.

Cheers

mainTAP

Dear all, Can you please advise if the following scenario is achievable using the Could Router Switch and how would the configuration look like : CRS_internal_qinq.JPG Basically, I would like the switch separate the traffic based on Service Tag rather than Customer Tag. The reason is that I want to ...

mainTAP

The switch also behaves differently when gets rebooted, is there any configuration applied only after a reboot ? I have also managed to remove the vlans above 4000 ( by factory default and applying the same configuration ) .. which should not be the case .. But the switch still leaks like a hub, com...

mainTAP

Hi there, Can you please advise how the console on the Core Router Switch works ? As I have tried different cables but still not getting output, if I press enter it prints one unknown character. I have tried original cisco console cable, straight and rollover cable with juniper RJ45 to DB-9 adapter....

mainTAP

Dear All, Can you please help with issue I have with CRS125 and simple VLAN scenario where ethernet-1 is a trunk port with vlans 1,100 and port8 should be access port for vlan 1 and port16 access port for vlan100. Unfortunately I cannot make a port as an ACCESS port on this switch, when I mirror the...

mainTAP

What do you mean by changing it from gateway to normal one? Are you doing NAT on that router ? If yes, change masquerade rules to your new 'gateway' interface. Check your DHCP, IP addressing and bridge to swap 1st port with 10th.

mainTAP

Hello, I am using ports 2,3 and wlan1 on RB951G-2HnD to switch traffic within one subnet (192.168.0.0/24). There is a server + another device behind port 2 and several hosts behind port 3. (+some wireless clients on the wlan1 interface) I have a bridge configured to join port2,3 and wlan1, but : -Wh...

mainTAP

The interface changed again :/ , I did not do any change nor the switch restarted and the web interface changed to RB260 :/
I am using chrome, by accessing through separate incognito windows I get the original RB250 interface. The switch is using swOS1.13.
It is a bit weird to be honest

mainTAP

Okay, I got it sorted, It works under a different browser / it stored some wrong information in the browser and messed up the web interface.
I don't know why I did not think of this in the first place

PS: sorry for posting in wrong thread.

mainTAP

Hiya,
The method using RouterOS works fine to recover RB250GS after downgrading from 1.13 to 1.10.
If you haven't got any routerOS device by hand, you might try tftpd from http://tftpd32.jounin.net/ which is a lightweight tftp server and the latest version can serve as DHCP server as well.

mainTAP

Hi all, My RB250GS started to behave very oddly after playing with VLANs. It seems that the switch thinks it is RB260 as the interface changed and I can also see SFP tab in the menu. I was using swOSv1.12 and added 3 VLANs , vlan1,vlan100 and vlan 200. I set the port 1 as passing all three vlans and...

mainTAP

Thanks for the tip rextended, for some reason it also works with domain name and it resolves the IP automatically

mainTAP

Here is the code for 2 websites, it can be easily modified to test more addresses. It is rather simple and could be done better but it might help you. Please be aware that the script expects the InternetStatus to be already set, meaning it runs the '#do something commands' just when the status chang...

mainTAP

I'll post the script in couple of hours when I get to a PC

mainTAP

You are welcome, to add more hosts would be easy, how many would you like to check for how many repeats? Do you want to consider the link down only if all the attempts fail?

As for the netwach functionality, i believe it pings just once and makes its decision upon the outcome.

mainTAP

Man, try to read the reply after your previous post !

mainTAP

Thanks for the correction. Unfortunately there are not many resources about mikrotik scripting language.

mainTAP

Hi cicserver, instead of the inbuilt watchdog I am using a simple script which ping an IP address 5 times not just once and just after all 5 failed attempts it performs an action ( this can be adjusted to less than 5 ) . Hope this might help : :local i 0; :local F 0; :local date; :local time; :globa...

mainTAP

mainTAP

Have you installed LED package ? Try to check if system/leds is set to correct type for wlan-led.

mainTAP

Anybody knows what might be the cause of this issue ? Or should I submit it as a bug of routerOS ? I would really appreciate, thanks

mainTAP

Hi there, Could somebody please explain or give a hint what could cause this behaviour ? I have a RB751G-2HnD set up as a client and connected to a wireless AP ( which I have no access to ). The router connects to the wireless just fine, can reach all it needs as well as the clients behind RB751G's ...

mainTAP

Hi, is there any solution for this particular problem but with dynamic Public IP and also default gateway ?
I have a similar problem with my mikrotik and ADSL modem, but I get different Public IP and default gateway IP for each connection.
Thanks

Search found 57 matches