MikroTik

rxfoote

I have a 1GB connection from service provider, when plugged directly into their connection I get 950+Mbps. When through the Tik, 160-200Mbps. I have WAN on Ether11, LAN on Ether1, firmware at 6.39.2. Any thoughts/ideas? Thanks!

rxfoote

I have WAN setup on port 11, and LAN on port 1. Still considerable slow speeds. Directly plugged into provider, close to 1GB, through Tik now after upgrading to 6.39.2 160-200Mbps. Thoughts/ideas?

rxfoote

I went with the RB1100AHx2 - quick question though. Plugged into connection directly, I'm getting download speeds in excess of 900Mbps, and through the Tik between 400-600Mbps. I have a very generic/plain config right now. Any ideas? I don't really care much, but the client his a Gig connection, and...

rxfoote

Any suggestions?

rxfoote

Really, just NAT only. Will have a few basic firewall rule

rxfoote

Getting a new 1GB connection, and would like as much bandwidth as possible. Current RB2011 I already had, won't push much more than 300MB. Will the RB1100AHx2e be adequate, or go to a CCR? Thanks in advance!

rxfoote

Downgraded both to 6.33, still no issue. Then upgraded both to 6.37.1 and the tunnel is up!

rxfoote

I have had a IPSEC tunnel up for a couple of years. Then this morning out of the blue it is down, saying phase1 negotiation failed due to uptime. I have gone through the config over and over, reconfigured with the same results. Any suggestions or ideas?? Thanks!

rxfoote

I am trying to setup a l2tp/IPsec vpn for new Mac users. I have it setup, however I'm getting a failed to pre-process ph2 packet in logs. I have removed the default group policy from IPsec peer. However, I still get the error. Any ideas? Thanks!

rxfoote

The WAN connection is not using PPPoE

rxfoote

Thanks for the response, I have setup fasttrack - will watch and see if any difference.

rxfoote

We have a new RB2011UiAS setup, with very simple config. Our bandwidth is 300MB, and tests as such if I config. a system directly with the static IP info. However, going through the Tik we never get much more than about 80MB locally and testing with ping speed on the Tik itself. Any thoughts or idea...

rxfoote

I am looking to setup a simple network for a Café. We will have a WAN connection, LAN for internal network, LAN for customer wifi, both LAN networks separated. We would like to run the wifi as a hotspot with a landing page. Which routerboard hardware product will support doing this? Thanks in advance!

rxfoote

I have messed with MTU, MSS, and clear DF via mangle. However, issues with phones still exist. Would I be better off with a different tunnel than IPsec? Thanks!

rxfoote

From what I have been reading I may need to set the IPsec tunnel to clear DF bit. However, I can't find where to do this? Thanks!

rxfoote

Client has two locations, that have had a point to point between them. To cut down on cost and increase speeds, they are switching over to a Comcast connection. I have put a RB1100 at each location. I have an IPsec tunnel created and traffic is flowing between them without issue. At the remote locat...

rxfoote

I have a RB1200, that I would like to setup for our two connections. The first as primary, and the 2nd as secondary. I would like it setup, so if the primary goes down, it automatically moves over to the 2nd, and then if the primary comes back up to automatically move back over. Any guidance in how ...

rxfoote

I have a RB1100AH setup with a Comcast connection, with Comcast in bridging mode. With the Tik in place browsing is beyond slow, not even really useable. Yet, if I remove the Tik it is as expected. The Tik has a very basic config.... Any ideas or things to check? Thanks!

rxfoote

Thanks to Ryan for all the help! Basic config; PPTP Server 1. Open PPP from the menu, click the profiles tab, and select the default-encryption profile 2. Open the profile and enter 10.1.1.1 for the local address line and 10.1.1.2 for the remote address line. 3. (IF you have ipv6) Select the Protoco...

rxfoote

Thank you, your instructions work perfectly! I can ping across the VPN on both Tiks. However, from the PC side I can only ping across the server side to the client side. From the client PC side, I can't ping the other side. Any ideas? Thanks!

rxfoote

Email sent, thanks!

rxfoote

Thank you, I will go through it! Any chance something with Winbox? I'm fairly new to RouterOS and not confident I could do via cli. Thanks!

rxfoote

Does anyone have instructions for a site to site PPTP VPN tunnel setup? Thanks!

rxfoote

I setup a RB1100 and a main site and a RB750 and a small remote site this past week. I have setup IPsec setup and it if functioning. However, it is so slow it is not even useable. The remote site is setup to RDP to a Term Server on the main site. The VPN tunnel is so slow, it won't even connect. Yet...

rxfoote

The RB450 is what I am referencing in regards to the PPPoE issues. It is behind the Netgear. With just the Netgear in place doing the PPPoE it is fine. As soon as I put the 450 in place doing PPPoE, it becomes incredibly flaky.

rxfoote

I have a client with several offices that we have IPsec tunnels connecting all offices. Today, I attempted to setup one of the owners home offices. I put his DSL modem(Netgear modem), in bridging mode and setup PPPoE client on the 450. It authenticates and gets out just fine. However, it disconnects...

rxfoote

It ended up be an issue with a NAT rule/masquerade. It is working now. Thanks for the replies!

rxfoote

Thanks for the reply! I have done this as well as enabled nat keep alive and mapping directly on the Cisco phone. I can hear them talking, but they cannot hear me.

rxfoote

I've read up a bit, and apparently I really shouldn't need to open this range as the default "established allow connections" should handle this. Is this correct, and if so why is it not working? Phone calls can be made and I hear them, but they do not hear me. Thanks!

rxfoote

I have a client that has a few hosted VoIP phones on their network. I need to accept the port range of 10000-20000, to the entire internal network in and out. I assume this need to be done with a filter rule? I am unsure of how to do this on a Tik. Any suggestions? Thanks!

rxfoote

Thanks, changed ethernet to bridged and can access w/out issue!

rxfoote

Thanks for the reply - I have it set as shared right now.

rxfoote

I haven't searched a ton, but haven't found anything in this regard yet. When setting up a Tik for the first time from an Apple via Parallels(Windows 7) I can get on it the first time no issue via 192.168.88.1 - However if wipe out the default config. then you cannnot. Something happens with the MAC...

Search found 33 matches

RB1100AHx2 slow wan speed

Re: 1GB Connection, what hardware?

Re: 1GB Connection, what hardware?

Re: 1GB Connection, what hardware?

Re: 1GB Connection, what hardware?

1GB Connection, what hardware?

Re: IPSEC tunnel issues

IPSEC tunnel issues

l2tp/ipsec vpn setup

Re: RB2011UiAS slow speeds

Re: RB2011UiAS slow speeds

RB2011UiAS slow speeds

Which RouterBoard

Re: IPsec tunnel and issues with Shoretel

Re: IPsec tunnel and issues with Shoretel

IPsec tunnel and issues with Shoretel

Dual WAN/Failover

Slow Browsing

Re: PPTP Site to Site VPN

Re: PPTP Site to Site VPN

Re: PPTP Site to Site VPN

Re: PPTP Site to Site VPN

PPTP Site to Site VPN

Slow VPN Tunnel

Re: PPPoE issue

PPPoE issue

Re: Filter Rule/forwarding question

Re: Filter Rule/forwarding question

Re: Filter Rule/forwarding question

Filter Rule/forwarding question

Re: Winbox via Parallels

Re: Winbox via Parallels

Winbox via Parallels