Or would it be 172.1.100.19:19

Or does it matter really, as long as it matches on both ends?

Thanks barkas and samsung172,

Let me make sure I understand this:

@samsung172 - So in area1 router 19 (172.1.100.19), I need access to the PPPoE Concentrator, so I VPLS tunnel from router to the concentrator (172.1.100.1), I would structure the VPLS ID as EDIT: 19:172.1.100.19 correct?

I doubt it. Just call your ISP if your using a residential provider and pay the $10 extra for the static IP which will allow what you need.

Hello guys, So I'm very new to OSPF and MPLS and VPLS, just switched our bridged network to routed and these have made it really simple for the switchover. I have VPLS working but id like to have it set up correctly as in best practices and 1:1 and 2:2 and 3:3 don't cut it. Ive read http://forum.mik...

Well looks like im going to have to go the RMA route. Although 6.0 seems to have fixed the issue, pppoe is broken and does not add correct mangle rules upon user sign in. Darn it!!! Any suggestions on what i should replace the 2011L with? This is our second 2011 and both seem to have had their own s...

I have the exact same issue, my less than 60 day old 2011L-RM repeatedly would loose network access and would have to be rebooted 20 times a day, the device was still powered on and I could access through winbox, which I thought was odd, but any traffic that was to be routed through failed. I setup ...

I run my RB411GL's and Omnitik's on ROS 5.22 using dynamic-mesh and everything works great.

Whats your configuration?

I think this will work but it is untested, please use carefully! Review the export below and adjust to your settings as I do not know the exact setup and am not there to ensure so. *Make sure the wlan interface on each device is called wlan1, if not adjust the script below to the correct name. *Adju...

I dont believe this is possible if you cannot change anything on the modem. Maybe throw in a small tik device between the modem and your device just so u can get the static IP?

Could you possibly put the modem into a bridged mode and have the tik handle the wan?

You can use whichever port you want. Just make sure you add the used ether port to the bridge that wlan1 resides on.

I didnt realize it was SwOS, my mistake for not reading all the way through.

I tend to leave the antenna gain setting to 0 which is default. I would check your local regulations on what the max you can transmit and adjust accordingly.

Attatch the vlans to the wds interface on both sxt's and create a bridge with the vlan from wds and the same vlan on the ether port from the RB750. Add a dhcp-client for that bridge and it should grab one through that vlan if dhcp-server is setup. You now should have access. We have accomplished alm...

I had this same issue but on my RB411GL, After consulting support, they instructed me to perform a netinstall of the latest firmware to ensure everything was a fresh install instead of an upgrade, and that fixed my port flapping issue, been 7 days and havent had an issue since. Maybe same issue with...

Sounds like you have configured the mikrotik correctly but the modem has been left unconfigured. Possibly an arp issue. Add the mac and ip to the arp table on the modem and see if that helps. EDIT: Why not have the dhcp-server on the modem assign a static IP to the device and just have it set as dhc...

Need a bit more detail about your network topology and the settings on the mikrotik.

To clarify, when Internet is stable, the vpn works great? But when internet is unstable you have connection errors?

Are these clients creating the vpn connection through the wan or lan side?

An easy solution, under Ip/ Hotspot/ Server Profiles/. Set Rate Limit (rx/tx) to whatever speeds you have in mind. This setting will make every unauthenticated user share the bandwidth you define under that setting. Or at least that's what i was led to believe, seems to work in our deployment for ou...

Yes that is possible, of course some factors must be taken into consideration, such as LoS, and or interference. But at 3km it should work fine as long as you have LoS. Setup your Omnitik as a ap-bridge with SSID and encryption, then wth CPE at remote location, set as station-bridge with same ssid a...

Ok so I have come to the conclusion vlans do not work on ports 1-10 on the RB1100AH due to the chips? im guessing based on a-lot of other topics discussing vlans and RB1100AH and 4 days of tinkering and never getting a working solution, So i must use ports 11-13 to accomplish what is needed as they ...