Cheers dgnevans. The backbone area is on both and the id is 0.0.0.0 here is the output of /routing ospf interface site A 0 D publics 10 1 broadcast none 1 D Backhauls 10 1 broadcast none Site B 0 D ether9 10 1 broadcast none These are the dynamic created interfaces. I did set up interfaces and the o...

Hi All, I am having an issue with implementing ospf. I am lead engineer for a small WISP 300 odd clients on 30 odd AP's. I am setting up OSPF for the first time. We use Mikrotik mainly. We have 2 microwave links coming into our main sites. https://dl.dropboxusercontent.com/u/29102346/Simplenet.jpg ....

Hi Guys, I have a bit of a weird one there are 2 sites. site1 gets 40/40mbps over a Wireless Licensed Link site2 is 100/100mbps WLL the 2 are interconnected via a wireless link each site has it own router. Each router has a number of AP'S connected. Due to a lack of public IP's on site1 a number of ...

Update. In an effort to gain winbox access to these units I created a VLAN interface and I can ping between RB'S but I cant ping from my PC and I cant winbox into anything apart from the router I am connected to. Core /interface vlan add arp=proxy-arp interface=publics l2mtu=1594 name="WDS Brid...

Hi All Was hoping for some input on a WDS bridge I am having a minor issue with. The wds is working fine and passing traffic but I cant access the mikrotiks with their management IP. Farside of the link 10.10.11.3 /interface bridge add arp=proxy-arp l2mtu=1526 name=backhaul /interface wireless set [...

No Answer from anyone? I dont need to use eoip if one could propose another solution.

Hi Guys got a question. I have a remote site 192.168.8.5 which is a 750gl this is connected to a warboard running star v3 ether-192.168.8.1/24 wlan-192.168.0.2/24 which is a wireles link to another war running staros v3 wlan-192.168.0.1 with an ether-10.15.20.5 which is finally connected to a rb1100...

Hi Guys, I have a strange one or at least I think it is strange. I have an 433ah acting as an AP which is fed by a Nano bridge ether1 the side facing the nano bridge has an address 10.6/24 and the AP side has a range 55.0/24 the AP has 55.1 as its address. I have static routed down to the 433 and ca...

Cheers Jos I might take you up on that offer I have most of it figured out. I have the radius server going and I can get the AP's to connect as NAS's. I only have the bandwidth management to sort. I was hoping to mange this from the radius.

Hi guys know this has been asked before but I can't find a dummies guide. I am setting up a s small network with 100 or so clients there will be 10 mbps both ways 1:1 contention. This will feed a 1100ah which I will refer to as the core router the core will 5 back haul links each feeding an AP all l...

bit of a noob myself so this may not work try adding /ip route add gateway=192.168.1.1

cheers for all the help figured out what it was one of my co-workers they put a queue but did not give it a target so it was queuing all traffic on the ap when I disabled the queue the rb performed as it should.

So from the 433 to your clients you are OK and from the 433 THROUGH the LAN to the Nano, you are not? Can you ping from the Nano's ethernet (the one which is TOGHETHER with the 433 via the switcher) to the 433's ethernet and see what you have? You use eth1 of the 433 or another eth that goes to the...

sorry old rule was removed after I done the supout

unsure on the switch chip I didn't knowingly enable it but I doubt that would cause 600ms + pings and 30%+ loss. From Nano to 433 link is poor have not tried a bandwidth test but again 600ms + ping and loss and that was the 2 of them joined by a crossover cable and me hooked onto one of the AP's tha...

I did and still the same result its back on auto now and is saying it has 100 full duplex

Hi Guys I am having a problem recently got a 433AH 3 120 16dbi sectors and 3 x Mikrotik R52N-M each running a access point. A Ubiquity Nanobridge is providing back haul is is set as a router this is feeding into a 5 port 10/100 switch which then in turn feeds the 433ah and a valemount warboard with ...