MikroTik

mrjoli021

Hello

I am running RouterOS version 6.13. I need to create a monitoring port to capture a trunk port group of two ports. I am new to MikroTik and not sure how to acomplish this?

mrjoli021

I have several servers on the ESXi on different VLANS. I need to be able to connect to them from a switch port connected to the MikroTik.

mrjoli021

ok im fairly new to MikroTik. Is there a way you can give me an example on on how I could accomplish this.

thanks,

mrjoli021

Hello, I have been struggling with getting my trunking to work between an esxi server and my MikroTik 1100 AH. I am running version 6.13 and I have read several articles that describe how to set it up, but none of these setups have worked for me. I would like to allow all vlans connected on ports 4-...

mrjoli021

I have a vmware server and I would like to create a trunk group on ports 4-5 and trunk them with all vlans. Below is my config. Please help. # jan/14/1970 00:32:37 by RouterOS 6.11 # software id = FP7P-M89C # /interface bridge add name=Trunk_ESXI protocol-mode=none add name=bridge-lan protocol-mode=...

mrjoli021

I have an esxi 5.1 server with two NICS that I would like to trunk to an 1100 X2AH running 6.11. The ports on the MikroTik is 3-4. I have several vlans connecting several ports, but I would like to trunk the esxi all vlans. this is my config # jan/07/1970 21:18:48 by RouterOS 6.11 # /interface bridg...

mrjoli021

They are at 1GB. both laptops say 1GB on them

mrjoli021

Interface 3 and 7 are set to 1GB.

mrjoli021

I have two computers connected to each other with an ethernet cable both support 1GB links. When I did an iperf test I only get 10mb. I checked and saw that the vlan those interfaces belong to is showing up as tx/rx of 10mb only. Not sure where to set it 1GB. I have set each interface to 1GB, but ho...

mrjoli021

That worked

Thanks

mrjoli021

I have a 1100ahx2 that came with version 5.14. I have checked that auto upgrade and it doesnt find any new versions or anything. I would like to upgrade it to version 6. I have downloaded it and and installed it in the main directory and rebooted and it still says version 5.14.

Any suggestions?

mrjoli021

Below is my config. I have the Access point now plugged into port 7 without the "Vlan Management" setting enabled and it is currently working only on Vlan21. The SSID on vlan 30 doesnt work. If I plug into port 2 it doesnt work. If I set the "Vlan Management" to vlan 21 then it w...

mrjoli021

I had this device working like this on a Cisco 2950 switch. Since the 2950 is a 10/100 l2 switch I decided to get an 1100 AH which is a Gb L3 switch. Everything works fine except the access point. If I dont set the default VLAN on the access point I can connect to it through vlan21 and the ssid on v...

mrjoli021

It is the EAP350. I have it plugged into ether2. If I just leave it without a Native Vlan tag on it then I can ping the access point and the SSID on vlan 21 get the correct IP, but Vlan 30 doesnt work. Where do I set the native vlan to 21 on the MicroTik?

mrjoli021

I have added vlan 21 as the native vlan on the access point. The access point is connected to port 2. I have two SSID's one on vlan 21 and the other on vlan 30.

I see the SSID's on the computer, but when I connect to them they wont give me an IP address and I can not ping the WAP either.

mrjoli021

It is an engenius access point.

mrjoli021

I have an access point connected to port2. This access point will be using native vlan of 21. How do I set the native vlan the MicroTik add interface=ether2 l2mtu=1594 name=trunk-10-phones vlan-id=10 add interface=ether2 l2mtu=1594 name=trunk-21-network vlan-id=21 add interface=ether2 l2mtu=1594 nam...

mrjoli021

Thanks

that worked

mrjoli021

When I plug into port 6 I get and IP from 192.168.10.0/24 range with default server of 254. But I cant ping 254. From the MicroTick command line I can ping 192.168.10.254. Right now I am plugged into port 10 and I have DHCP enabled and I get IP 192.168.21.77. There is only one DHCP-Server which is 1...

mrjoli021

Port1 is a connected to a Cisco 871 Router. I would need port 1 to be a trunk port for both Vlan's. What I dont understand is that why cant I ping 192.168.10.254 from the same vlan? I get an IP of 192.168.10.54 from DHCP Server 192.168.21.254

mrjoli021

I have a router with IP 192.168.21.254 this is also the DHCP server for both VLANS. it is connected to port 1 on the MicroTik. All components are plugged into Vlan 21 and I have several IP phones that I would like to plug into Vlan 10 on ports 6-8. Right now VLAN21 is fully functional with internet ...

mrjoli021

This is the entire compact export. # mar/15/2014 15:48:51 by RouterOS 5.14 # software id = FP7P-M89C # /interface bridge add name=bridge-phones add l2mtu=1598 name=bridge-network /interface vlan add interface=bridge-phones l2mtu=65531 name=vlan-10-phones vlan-id=10 add interface=bridge-network l2mtu...

mrjoli021

I have vlan 10 and I setup an IP address on the interface of 192.168.10.254. The main VLAN is 21 and it has IP. 192.168.21.251 which I can telnet into it and from the command prompt I can ping 192.168.10.254. I setup a DHCP-Relay for Vlan10 and I am getting the correct IP's from that vlan, but from ...

mrjoli021

I am trying to configure several vlans and trunking them to two separate devices. One is a WAP which is on ether10 and the other is a an ESXi box on ports 1-3. not sure what I am doing wrong but I cant seem to get the trunks to work correctly. [admin@MikroTik] > export compact # jan/25/1970 14:34:25...

mrjoli021

Hello, I have 7 vlans and I would like create two trunks one with 3 interfaces for a VMWare box and the other interface for a WAP. I am fairly new to routerOS and not sure how to accomplish this. I would like to pass all vlans to both trunks. Also I would like to make the Mikrotik a l3 switch to rou...

mrjoli021

not sure if I understand what you mean

so remove

/interface vlan
add interface=bridge-trunk l2mtu=1594 name=vlan-21-trunk vlan-id=21
add interface=bridge-trunk l2mtu=1594 name=vlan-50-trunk vlan-id=50

but then what do you mean add the vlan interface to individual trunks?

mrjoli021

Is there a better way of doing this cause this seems like the more vlans I add this config will grow exponentially. In cisco if I allow all vlans on the trunk then it is just one line of code on the interface. Also, what is wrong with my config, why cant I ping from vlan 21 on port 9 to a vm also on...

mrjoli021

I have three ports connected to a vmware server as a trunk port. I have a vm inside and I am unable to ping it on the same vlan. port 1-3 is for vmware port 6 is on vlan 21 and there is vm inside the vmware server also in vlan 21 and I cant ping across. /interface bridge add l2mtu=1598 name=bridge-n...

mrjoli021

I have added a bridge to create a trunk. I am on port 9 which is on vlan 21. my vmware host is on ports 1-3 which are part of the trunk. I have a vm on vlan 21 and I am unable to ping either the vm host or the vm itself. /interface bridge add name=bridge-phones add name=bridge-san add l2mtu=1598 nam...

mrjoli021

I have a 1100 running 5.14. I would like to create several trunk ports on ports 1-5. Ports 1-3 are going to a vm server 4 to a WAP and 5 to a cisco uplink. Not sure how MT does it. Can I create the entire switch as on big trunk port, or will I need to seperate them into three different trunks? What ...

mrjoli021

Not sure if I got this right. The idea is to have ports 1-3 for esxi, port 4 for WAP and port 5 for uplink. These will all be trunk ports. as far as access ports go port 6,9 are part of the native vlan 21. and 7 part of the public vlan. Also according to this method not sure how to create the other ...

mrjoli021

1100 AHX2
RouterOS 5.14

mrjoli021

My setup is as follows. I have port 6 connected to a router which is assigning DHCP. ports 1-3 are for esxi and 4 is for WAP. native vlan is 21. from the lan port of my router I can access the internet, but I cant ping the WAP or esxi. and from the WAP I am not getting dhcp. add l2mtu=1598 name=brid...

mrjoli021

I need help creating two trunks ports one for an Vmware esxi with three ports and the second to a WAP.
vlans 10,20,30
interfaces for esxi = 1,2,3 (etherchannel)
interfaces for WAP = 4

mrjoli021

I have port5 on the HP set as a trunk port which is plugged into port1 on the MT, but I cant seem to ping the MT from the HP Switch. I am pinging it from the native vlan. Same config on a cisco switch works fine. Native vlan is 21 /interface bridge add l2mtu=1594 name=bridge-native add l2mtu=1594 na...

mrjoli021

I have a client that has an HP1810 l2 switch. I am installing a MicroTik 1100AH and it will be a router as well as an L3 switch. I believe I have configured the Mikrotik correctly but I cant seem to get the trunking port setup correctly between the MT and the HP switch. Has anyone had any experience...

mrjoli021

That worked thank a million.

mrjoli021

I am still not able to ping across. my MT export /interface bridge add l2mtu=1594 name=bridge-native-cisco add l2mtu=1594 name=bridge-phones-cisco add l2mtu=1594 name=bridge-workstations-cisco /interface ethernet set 0 name=winbox-172.31.0.10 /interface vlan add interface=ether10 l2mtu=1594 name=vla...

mrjoli021

this is what my cisco config looks like. Right now I have this in a lab and nothing else plugged into it except the MT and a monitor port. Port 12 is plugged into the MT with a crossover cable. The cisco switch is a 2950 but I am having the same problem with the production 3750. I also reset the swi...

mrjoli021

That is what I have always had. It doesnt show the encap since the cisco switch only supports .1q. Also, if I place ether10 to ip 10.105.21.197 I am able to ping across. I have ran wireshark and it shows that the request is getting to 10.105.21.200 but something is blocking it on the way back. Is th...

mrjoli021

Does it matter that the native vlan is 21 and not 1. I am seeing alot of errors on the cisco switch with native vlan mismatch. If so how do I force the native vlan and/or how do I disable vlan1.

mrjoli021

If I plug directly into ether2 I am placed in vlan 40 and get DHCP from the DHCP server in the other switch. I am also able to get to the internet. But I am not able to ping any of the MikroTik's IP from a different switch connected to vlan 40 or 21. Now if I place a different IP directly on ether10...

mrjoli021

If I dont put the routes in there I cant even ping each interface from within the router.

mrjoli021

if i put the native vlan ip on interface ether1 it works and i am able to ping, just on that vlan. Now when I place the same IP on the bridge interface I can ping anything from inside the router except all the sub int inside the router. and from a workstation I cant ping anything.

mrjoli021

I have added the ip's and routes below. I am not able to ping 10.105.10.197 from ether5, but I am able to ping 10.105.20.197 which is on a different vlan. On the cisco switch same senerio. I am not able to ping 10.105.10.197. The default gateway for my network is 10.105.21.254. Is icmp blocked on th...

mrjoli021

Thx
that is exactly what I was looking for. Now final question if I want to route between each vlan how will I do that. I would like to make this as a L3 switch?

mrjoli021

I have an 1100AH router and I would like to configure it in the following way. cisco switch -----TRUNK 802.1Q-----> MT on port10 MT has three VLANS 10 Native Port 10 20 Phones Ports 1-4,9 30 Workstations Ports 5-8 I have read on creating a bridge and assigning the native VLAN to the bridge as untagg...

mrjoli021

It happens the same with vlan 10. All traffic still goes through the ether1 and not the vlan.

mrjoli021

I have installed RouterOS on a VM. I would like to assign an interface to a VLAN for example. I have ether1 with ip 192.168.1.1 and I would like to put that on Vlan1. I have done the following but I still see all traffic going through ether1 and nothing through vlan1. /interface vlan add name=VLAN1 ...

mrjoli021

I would like to aggregate multiple WAN links. I have looked at mptcp but not sure if it supported on RouterOS. This is the scenerio. I have three DSL connections at 3mb each. I would like to create some type of VPN tunnel to my DC and have 9mb at the LAN side of the mikrotik and 9mb at my DC.

mrjoli021

I am trying to get a splash login page setup. I dont want to use a hotspot. I just want a php login page and I want to control the login myself. I have not found any article or explanation on how to create a simple login page without a hotspot.

Search found 51 matches