I got new features on my hAP mini! Interface #3, pwr-line1 Flags: D - dynamic, X - disabled, R - running, S - slave # NAME TYPE ACTUAL-MTU L2MTU MAX-L2MTU 0 RS ether1-GW ether 1500 1598 2028 1 RS ether2-Telia ether 1500 1598 2028 2 RS ether3-RaspberryPi ether 1500 1598 2028 3 pwr-line1 ether 1500 15...

I tested that and it works just as I hoped it would:

http://forum.mikrotik.com/viewtopic.php ... 60#p518660

Why is it not possible to bridge the LTE and ethernet port together? Now there is one additional NAT in the network setup because of this...

Interesting trick: I bumped the license up to level 4 and I now have a 2 chain 5 GHz ac AP AND a 1 chain 2 GHz AP that can serve MULTIPLE clients! Away went the limit of only one client connected to the 2 GHz interface!!!

I have installed R11e-5HacD on RB/953GS-5HnT but it’s not shown in the interface list!

Remember that you need to activate the wireless-fp package to enable the R11e-5HacD...

Does Mikrotik have a specific reason why the USB port is a Micro-AB port? These type of ports break down quite easy as you can by mistake insert a Micro-B connector the wrong way. I would suggest that the port would be switched to a Micro-B port in the future...

So the next question is, does the RB953GS-5HnT have a USB hub so that one can run 2 miniPCIe modems AND a USB device at the same time? http://routerboard.com/RB953GS-5HnT edit: answer was in the pdf: One powered USB 2.0 port, cannot be used simultaneously with J404 miniPCIe slot for 3G modem (softwa...

Cool! This opens up new options in my network design now!

Just noticed a thing that I didn't think was possible: I have a RB912 that is equipped with a r11e-5HACD MiniPCIe card and I'm still able to use the USB port for a 3G modem! Shouldn't the r11e in the MiniPCIe slot disable the USB port? Or is it just odd luck that it happens to work when load on the ...

I have 2 of the RB912 2GHz versions running a r11e-5HACD inside and they work just as they should...

Did you enable wireless-fp? R11e-5HACD needs that...

Try this:

http://bit.ly/1yYZZiK

Do note that the RB912 is a dual chain device and Metal/Groove only has one WiFi chain... With a large amount of users the benefit of two chains is evident...

I have a RB951G-2HnD on ROS 5.26 and it works with the WN772N. 6.XX branch drops the functionality...

There is a MAC address listed only for ETH1 & WLAN, does this mean that ETH2 is only for PoE out use?

What is the ambient temperature that the box is in?

OK, by feeding the USB port externally with 5V then the port comes alive but on the board there doesn't seem to be a point where to pull 5V from. Would need to build one from the main power line. Seems like the system is more or less running on a 3.3v voltage...

Have you switched the port type from USB to mini-PCIe?

http://wiki.mikrotik.com/wiki/Manual:US ... _port_type

Tried the USB mod on my 951-2n... Does not work. No power supplied to the connector at all. Bummer!

The MC7710 uses u.fl connectors on board and I have SMA-u.fl pigtails. An external antenna is connected to the SMA connectors. You need to know what frequency you will use for your cell connection and choose the antenna to match that. Running ROS6.7 and newest FW03.05.24.00 on the MC7710 so can't sa...

I use the Sierra Wireless MC7710 LTE module with a RB912UAG in DIP mode. I'm very happy with the stability compared to a USB dongle especially in weak signal strength conditions...

An old thread will be lifted up but: I have a recently bought RB411GL that stopped working, nothing seems to help. Netinstall 6.4 and 5.26 both completes successfully but on reboot all board leds lite up and stay that way until power down. Only way to bypass that is to press reset while powering up ...

Hello, The routerboot ar9344-3.10.fwf file found for the RB912UAG-2HPnD on http://routerboard.com/RB912UAG-2HPnD does not work. For both the RB912UAG-5HPnD and the RB912UAG-5HPnD-OUT the file is ar9340-3.10.fwf. Is the file listed for the 2GHz model the wrong one? Atleast I'm not able to update my R...