One question nobody has answered is if its possible to have fixed rate. That's you bill weekly, monthly, etc even if the customer doesnt use the account its expires after that period.

Guys, kindly help me sort this out.

I have got two routerboards one has 2.8.22 and it doesnt have Nstreme while the one with 2.8.15 has Nstreme.

Does Nstreme really improve a link? Which is better for a P2P link - WDS or EoIP?

Thanks

Depends on if you want a transparent proxy or not but this would be very useful.

http://www.mikrotik.com/docs/ros/2.9/ip/webproxy

Its straight forward, or buzz me on Yahoo IM with odugbesana

Thanks I was able to use WDS but EoIP never worked. I am using MT ver 2.8.11.

What can be done? DO I need an upgrade?

Thanks once more

Is it possible to do a 17.5km link that would carry two E1 lines (that ~ 5mbps) using the Atheros 5Ghz 100mW radio and 26dbi mesh stelladoradus antenna?

If yes, would EoIP give a good latency?

Thanks as I await ya reply.

So please how can I achieve a simple bridge to connect 2 networks?

Thank you

I now have the following Bridge [admin@Nitel] > int [admin@Nitel] interface> print Flags: X - disabled, D - dynamic, R - running # NAME TYPE RX-RATE TX-RATE MTU 0 R ether1 ether 0 0 1500 1 X ether2 ether 0 0 1500 2 X wlan2 wlan 0 0 1500 3 R wlan3 wlan 0 0 1500 4 R MyBridge bridge 0 0 1500 [admin@Nit...

Please can soembody help me with configuration for a Point to Point link using two MT with 200mW Prism?

I want to plug Device A and Device B at the end of the radios and A should be able to PING B and vice versa.

It was quite easy with senao bridge but not same with MT.

Thank you

Good, I tried it but all of a sudden i am get a Mising Plug-in error for winbox. This is what I have:- 1. The MT has two interfaces bridged 2. The MT is only used to monitor and shape bandwidth Now I want to create a Firewall Chain that would caused all traffic that are suspected to have virus/worm ...

Please can anyone help me how to block Blaster and anyother know worm/virus from sending trafic to and from my network.

Thanks you

Hi,

You didnt say how you figure it out. Meanwhile, I am having same problem and I cant install the OS so I would like to know how u solved the problem.

Thanks

Its taking time to boot from the NetInstall. Over 10 minutes and it didnt go thru.

Done that but my NIC keeps showing disconnected - reconnected sign. meanwhile, what the default username and password?

No, its a RouterBoard with V 2.8 installed

How can I do a password recovery for a RouterBoard 200. I have tried reset CMOS and no luck.

Thank you in advance

I have a Mikrotik Base Station and Ihave configured a RADIUS - Advanced ISP billing . I want the Mikrotik base station to send all authentication request based on the clients radio's MAC address to AIB. Is it possible? I enable MAC AUTHENTICATION and configured my AAA but I cant see MT sending any r...

Thanks guys! It worked!

So can I use 2.8.18 to upgrade 2.8.16? And how ill I get the software key as in would I need to reregister again?

Thanks in advance

Is it possible to recovery a lost password?

Thank you

Men thanks! It worked like magic but... what really happened or caused it?

Have a yummy day!

My RouterOS wont boot after a power failure. When I connect a monitor to it all I see on the screen is...

LILIO 22.3.4 Loading System.....................
BIOS data check successful
Uncompressing Linux....Ok, booting the kernel
Starting...

And it ends there for hours.

Thanks Pals, I finally got the HotSpot to work and it does so beautifully. The only problem now is how can I exclude some systems from been authenticated?

Thank you

YomiCiouz

Yeah, thanks! But when running the HotSpot setup, I am forced to use another port for www services since it appears port 80 is default for HotSpot. Hence after changing port in IP->Services I still have to do some changes manual in Firewall but after doing this I could get the login screen and logon...

Hi, Can anybody help me out? I am running version 2.8.11, I have a bridge (IP = 10.0.0.1 for Admin purpose) which contains three NIC; ether1 connects to the Internet, while ether2 connects to a switch where other nodes are connected. The Microtik box was actually designed to be a bandwidth manager, ...