My rule of thumb for reliable, rain-fade-proof links to customers, is to keep the distance to 100-150m below what MikroTik says the radios can do. I have had success installing MikroTik 60GHz gear up to 800m (wAP 60 to LHG 60's), but usually try to keep it to 700m or less, and 450m or less for Cube...

The calculator is for 5GHz only (it actually says that in your images). Don't use it for estimating 60GHz links. Fine thanks. This morning we have tried to make the connection on the beach, and it has been impossible in 60GHz despite having antenna B at a height of 15 meters from the mast and anten...

Fine thanks. This morning we have tried to make the connection on the beach, and it has been impossible in 60GHz despite having antenna B at a height of 15 meters from the mast and antenna A in a building more than 10 meters away. Without obstacles and with good weather. He was barely able to connec...

Hi, I have a pair of Mikrotik 60 PRO AC equipment (CubeG-5ac-60ay). According to the information on the web, they can make links up to 2.4 km, however on the calculator page www.mikrotik.com/calculator any link above 300 meters shows it as impossible. Any experience with this equipment at 60GHZ and ...

Hi, i need some input about how to install bitwarden in a container inside of a router based in arm.
It is possible?

i have the same scenario and the same problem.
Our version is 6.43.6 in CHR and CAPS
Any solution or work around?

thanks,

Thanks MKX, Pfsense and MKT Router are connected using a ethernet port in access mode (connect via cisco equipment) without vlan tagging. Note that is possible make a ping between MKT and clients WLAN. (I asume that tagging in CAPSMAN datapath config is ok), and between into MKT and PFsense. Not is ...

I have the following scenario, where I want to introduce Mikrotik equipment. On the one hand there is a pfsense router that I can not change, and that performs the work of Internet output, with an interface in vlan 798 and ip in that vlan On the other hand I have Mikrotik equipment, which are config...

I need help with a configuration. I have two interfaces, Ether-69 (ip range 192.168.109.0/24) and Ether-70 (ip range 192.168.110.0/23). The 69 is for the CAPs and the 70 for the wifi clients. In the network 70 I also have connected my gateway (192.168.111.254) (cisco device that gives me Internet ac...

Me too.
Any sugestion?

The first step : Disable de FW in your laptop

ufff!. At least the config run.

I try to use a trunk in port eth3 to eth5, eth1 as WAN. Vlan interface in vlan 20,30,40 and 50 After that i connect my laptop into Ether4 (with vlan tagging activate for the connection in vlans 20,30,40 and 50 in the laptop), and i can get ip configuration (via dhcp from Mikrotik dhpc-servers define...

I have a problem with the boot process of the router. It is reset by an unknown cause (possible electrical failure) and after that in the boot process I see trying to up the ethernet port, but below disconnects. (From winbox i got a MAC one time) I've attached a demo at my table and see that there a...

Thanks por the reply. Using a normal cable the link is down always. I have a question relating to the cable, is it possible that the cable used to power the router inhibit the auto-negotiation process? The cable I use is the one provided by the manufacturer for the equipment. All cables were tested....

I have two routers connected, SXT-5HPnD and OmniTIK UPA-5HnD through ethernet interface with a crossover cable (female/female) and the corresponding power injectors. RouterEthPort->Inyector->Crossover-cable->Inyector->RouterEthPort Both interfaces are configured with auto negotiation and Full-duplex...

Im trying to use SNMP to read and make graphs with cacti.
Im using a script in php, download from the cacti page, and i found some problems with it.

I dont found this value: 1.3.6.1.4.1.14988.1.1.1.1.1.5 for my release of software "MikroTik RouterOS 5.26"

¿any idea?

I have had two similar problems hardware in a very short period of time . On one hand I missed a U- 5HnD OmniTIK . And now 5HPnD Mikrotik Routerboard SXT . In both cases I do not get the ethernet port online . In case of SXT at the beginning of the boot process , and before the startup beep , beep s...

Can anyone tell me how to correctly deste grounding device?
Can it be welded to the plate to save space?
Is it enough that the metalic connector grounded?

Any photograph will be welcome

Thanks for your support. The problem is that the second beep does not occur and when I try to use netinstall (or winbox) the OmniTik not is show, nor MAC and nor IP address access. I try to access using reset button (following the instructions) and waiting 30sg. After 30 s the led stop blink (change...

My OmniTik is dead. After start only one beep sound, and no more responses. No ligth when plug in ethernet ports, and winbox and netinstall wont detect it. (nor MAC nor IP). I look for connect serial port (to console) using USB port, but i dont found any information, probably they cant. ¿They can bo...

Hi, I have problems to connect with the equipment. I purchase a router "Omnitik" and i wont connect with them. They dont ape I try using poe (eth1 port) and also eth2... but any method run. After power omnitik using poe only one beep sound. The computer turns on, shows a green LED, but doe...