MikroTik

jfvelamoscoso

I fixed the err disabled but I am still having issue.

Gi1/0/1 notconnect 202 auto auto unsupported

jfvelamoscoso

Hello,

Does anyone tried mikrotik transceiver on a Cisco SW? I have S-3553LC20D and S+31DLC10D but none of them are working I got the following on the Cisco SW.

Gi1/0/1 err-disabled 202 auto auto unsupported

Best regards

jfvelamoscoso

Is this a active topic?

In my scenario which device will you consider to use it

300 IP i the same broadcast domain.
6000 packets per second
Bandwidth 50 Mbps 1:1 Full duplex

jfvelamoscoso · Re: Queue simple not working... use 192.168.6.0/24 as target

use 192.168.6.0/24 as target

jfvelamoscoso

Cable UTP cat 6

jfvelamoscoso

hello anyone know if mum colombia is streaming the sessions. I was on the official youtube channel but suddenly said that the transmiter stop the service

jfvelamoscoso

What kind of problems do you have. I have a bgp session running OK mikro since 2013 and is working perfect

jfvelamoscoso

For short distances? How can you compare SXT for example to Ubiquiti. I want to know if SXT 5Hpnd for example could be compare to air grid to loco or to nano bridge.

About lond distances, how about netmetal?

jfvelamoscoso

Hello, I have been working with mikrotik for more than 2 years. I am playing with mikrotik radios but i want to see a fair comparison. Which mikrotik AP can be compare with which Ubiquiti AP. Mikrotik SXT 5Hpnd VS Ubiquiti ? Mikrotik ? VS Ubiquiti Nano Bridge? Mikrotik ? VS Ubiquiti Nano loco Mikrot...

jfvelamoscoso

digging something i found this.

When the port eth1 on R2 is in the bridge I can reach AP2 but not AP1. When the eth1 is not in the bridge mode i can ping AP1 but not AP2.

Any idea?

jfvelamoscoso

Hello, I have one antena Omnitik Connected as the picture attached The antenna (AP1) is not replying to R2 neither R1 but AP2 is replying ok. ETH3 is slave from ETH2 and both are bridged to ETH1. The wear part is that if i disconnect AP1 to the network and connect a laptop with the same cable, it st...

jfvelamoscoso

I found the problem. My router was been used as a DNS Server and it has allowed request activate.

jfvelamoscoso

I forgot to tell the traffic is more than 3 Mbps which is too much for dns

jfvelamoscoso

This IP are found on Source address, and the destination is the router. On ip firewall connections. I can find different source porte but the destination port is always the same 53. This traffic is unexpected because as i said there is no host behind the router. Looks like the router is uploading al...

jfvelamoscoso

I found also this IP

103.243.20.43
94.190.193.121
201.34.145.201
209.216.126.207
189.79.40.16
192.185.26.193
194.6.233.17

jfvelamoscoso

I am getting on torch a lot of traffic upload to this ip:

31.6.71.253
31.6.71.254

But there is no user behind this router, looks like the router is uploading this information.

Does anyone know what service is uploading? or Why is this?

jfvelamoscoso

It is general because i allways desiging networks.

In some places clients will use lot of vlan, other queue (simple or tree) other could be using routing protocols, etc.

The best answer will be.

example:

queue tree: 80% CPU 10% ram
BGP protocol: 90% Ram 10% CPU

or things like this.

jfvelamoscoso

Hello all.

Please some expert, i allways have a doubt on which device is the best for me ( I don't want to kill an ant with a canon)

Which proceses or which functions require CPU and which RAM

jfvelamoscoso

No one?

Also i just realice that when is a parent, you can't get the snmp traps. I am right?

jfvelamoscoso

Hello guys, i have the scenario attached in the picture grafico.png . I realize right now that the server only can get the oid information from R1 when i am monitoring from one pc next to the server. Server is trying to get oid from bytes on queue tree. When i close the conection between mi pc and t...

jfvelamoscoso

Please give me a diagram and the result of /ip firewall nat export compact

jfvelamoscoso

If i got you right, the DCHP Server is your device and you are trying to get the dinamic ip on wan port of mikrotik.

You have to enable the interface under
/ip dhcp-client

Otherwise please send me a diagram an copy the result of /export.

jfvelamoscoso

Please enter to you router using telnet / ssh or on terminal tab of winbox/web. Type /export and copy your result here.

jfvelamoscoso

You only have to nat on the border router (router connected to isp). Because you are using ospf and it is full implemented, you should not need nat on all the devices behind, because BR knows how too reach the other devices. I really don't like masquerade because you really don't know what is happen...

jfvelamoscoso

you can only disable leds which are behind /system leds

jfvelamoscoso

Nice, Well not nice, but is good that you find the reason. They apply the same policy on my country (Perú) some time ago but oonly on residencial services

jfvelamoscoso

Hello,

Does anybody know about some made for mikrotik (Mikrotik doesn't have it) that deliver with big HDD. Other option is if anybody know which is the maximum capacity of USB that mikrotik can support.

Best regards

jfvelamoscoso

Nice,

I am very happy that it work, feel free to contact me if you need any help in the future

jfvelamoscoso

Please check if the packets are passing through this rule you can check it at winbox

jfvelamoscoso

Think that you will not be able to connect the mikrotik outside your office if you have a private ip, maybe if you ask the isp to give you an port fowarding. But not sure if they would like. About fortinet really don't know about it, but some devices show they public ip no matter you have an private...

jfvelamoscoso

OK, just disconect your modem to test if it is working, it is not matter of it. On routerboard just add this rule. ip firewall nat add chain=srcnat action=src-nat dst-address=192.168.0.2 src-address=!192.168.0.2 to-addresses=192.168.0.1 out-interface=xxxx. This rule says that each packet that goes t...

jfvelamoscoso

Yes it will private to use DDNS because your server or device doesn't use any public ip, this ip is shared by a lot of people. If they ISP can give you and Public IP Pool you can solve this issue, just in case you need public ones. Otherwise they are using 10.x.x.x/8 if you use any 192.168.x.x/16 yo...

jfvelamoscoso

This is the same that some ISP are doing on my country. The ISP is giving you the private ip 10.x.x.x/8 this is set up on their servers. On some router their nating several clients to the same public ip in order to not use to many ip. I know it is ugly but this is how they are doing. You only have o...

jfvelamoscoso

Could you connect the device directly to ethernet port on port 5. Then try to connect to it via winbox using the neighbor tab.

jfvelamoscoso

Can you make some graphic of the topology how everething is connected specifing ports?

jfvelamoscoso

I was the person who made this topic like one year ago. I have to admint that at the first time i was not so convice to use it because i had been trained on Cisco. Right now after one year, i am talking to other persons how good is it. I can tell you that i have take Mikrotik up to limit having 98 %...

jfvelamoscoso

I made it work just changing from this:
Options[_]: growright,bits

To this:

Options[_]: bits,growright

jfvelamoscoso

Hey guys, i want to implement this solution and i don't know if anybody have made something similar. I am using a icinga (Is similar to Nagios) as a Central Server of monitoring SNMP. And i have Dude servers in serveral offices monitoring the Lan of this. What i want to do is that all the Dudes repo...

jfvelamoscoso

The problem is that your graphs on mrtg are on bytes and on webgui are on bits.

I am facing the same problem now, any advice?

jfvelamoscoso

Hello, does anyone else has this issue. I have NTP Config on the equipment, but when I enable the graphing tool it shows as a date August 2150

jfvelamoscoso

Hello,

Right now i have exactly the same escenario. Can you give me some advice how you did it?

jfvelamoscoso

Hello,

I want to know if there is a table where i can see how many routes i can have in my routing table. Or how much consume of memory ram each.

I have a RB951-2n and i want to know how many ip routes i can have without turning the system unstable.

Best regards

jfvelamoscoso

Please can you post the result of

/ip firewall nat export compact

jfvelamoscoso

http://wiki.mikrotik.com/wiki/Manual:IP ... dress_list

jfvelamoscoso

Hello, I have 4 subnetwork on an mikrotik router. And i want to give IP to the clients by DHCP . I want that only allow users identify by mac address can get the IP. Right know if config • pool: Static-only • The mac is pairing to one ip on lease The problem with this is that when i move the laptop ...

jfvelamoscoso

I can help you by CLI

/ip firewall nat chain=dstnat action=dst-nat to-addresses=10.3.20.20 dst-address=192.168.3.20
/ip firewall nat chain=srcnat action=src-nat to-addresses=192.168.3.20 src-address=10.30.20.20

i hope this will help you

jfvelamoscoso

For create the bridge is just.

/interface bridge add name=THE NAME OF YOUR BRIDGE

/interface bridge port add interface=INTERFACE THAT YOU WANT TO ADD TO THE BRIDGE bridge=NAME OF THE BRIDGE

jfvelamoscoso

It would be better if you type the device where you want to config but anyway. First for setup the ip address. You don't have to set up as inside or outside /ip address add address= YOUR ADDRESS netmask=YOUR NETMASK interface=INTERFACE comment=DESCRIPTION Then for add ip routes. /ip route add dst-ad...

jfvelamoscoso

enter using telnet.

Type the comand

/ip address export compact
/ip route export compact
/ip firewall nat export compact

jfvelamoscoso

Hello, I want to config Qos using PCQ. My problem is that in our country usually ISP only assured one % of the mbps that the costumer pay. So in this scenary we have for example diferent plans 3 mbps 25%, 3 mbps 50%, 3mbps 100%. This costumer for example the first plan will get CIR=3*0.25 and mir=3m...

jfvelamoscoso

I am working on it right now. I have one that is working sending an e-mail. Each day but i didn't got the erase part yet. add name=backup_mail policy=\ ftp,reboot,read,write,policy,test,winbox,password,sniff,sensitive source="\ :log info \"backup beginning now\" \ \n\ \n:global backup...

jfvelamoscoso

Hello i work on a ISP and we are choosing equipment. We were working for the las 6 months with Mikro and we really love it. But we have the doubt. Wich are the advantages and disadvantages of use mikrotik insted of Cisco. Or in which cases we should use one or other. I would like to know from your e...

jfvelamoscoso

Hello,

I was config today the email tool and realize that when i print the configuration the password is in plain text. I like to work everithing from cli. Is there any option to cypher here?

Best Regards

jfvelamoscoso

It didn't work beacuse in this case if i bridge from eth1-4 i'll be doing a loop betwenn external an internal interfaces.

jfvelamoscoso

Thanks for the quick rep This looks like a 1:1 Nat, it could work i didn't try on my enviroment yet but it sounds as it work. I was thinking in nat only the port eth5 masquerading the packet with ip of eth1 because this is LAN network. And leave ethernet from 2-4 without natting. Because this ports ...

jfvelamoscoso

Hello,

I am trying to deliver public ips to some costumers. This is what i want to do and i think i need a little help.

The topology is show in the atachment. In this case i only want that the port eth5 will be nat using the public ip 1

Best regards

jfvelamoscoso

Hello I am config a BGP router(1) with AS1. I dont have any other AS behind this router. I am advertising my ip pool, but i don't want to receive the routes from the BGP (0) neighboor. I just want to know that the default gateway will be this bgp neighboor (0). What prefix-list chain i can add for h...

jfvelamoscoso

Hello,

I just found that there is a page mikrotikpasswordrecovery.com where you can upload your file .backup and you can get the password of all users.
I would like to know if there is any form to encrypt the passwords

Search found 58 matches