Hey guys, my RB4011 ARM is failing to upgrade, it downloads the package reboots, but then it's on 7.9 again. Any idea how to fix it? Export the config, netinstall, re-import. It's the savest and easiest way. :-) That seems quite the hassle, I think I'll wait for the stable of 7.10 and see if an upg...

Hey guys, my RB4011 ARM is failing to upgrade, it downloads the package reboots, but then it's on 7.9 again.

Any idea how to fix it?

Did you see this? https://www.netweters.be/t5/Instellingen-software-hardware/Docsis-3-1-E-router-CV8560E-bridging-actief/td-p/79981 It's a rather long thread, with additional links to others, and there's a lot of talk about IPv6. I didn't read it all, just skimmed through quickly, because I have to...

Is router connected directly to ISP, or is there some modem/another router in between? If it's direct connection, and you have /56, you should get it either from DHCPv6 as whole prefix (not just address), or it can be static config. But if it's the latter, I wouldn't expect DHCPv6 server on WAN pro...

Can you share what exact info you got from ISP? Mask addresses if you want, but don't overdo it, e.g. if there are some different subnets, it must be possible to tell if they are completely different or if one is part of another, etc. So my ISP gives me this: 2a02:1811:xxxx:8400::/56 This is what I...

So, my provider does not hand out a prefix via DHCP, the only thing I get is a DHCPv6 address from my ISP. I have a /56 network assigned to me and I get an IPv6 address from that range with default route: https://i.ibb.co/pfhtsMx/image.png https://i.ibb.co/pyxh2LV/image.png I can also ping to public...

Pirlet , FYI - I assume you are running a Mikrotik CHR (64-Bit ROS). Heads up - I don't think you need the "SCSI controller 0" in your configuration. If I am correct , the CHR does not even have SCSI drivers and the virtual CHR hard disk is actually IDE. By removing the SCSI controller , ...

Hey, let me just get into this thread because we're experiencing the same issue. Don't want to hijack but maybe it gives more insight to the problem and we can pinpoint more? Our setup is the following: Tyan Server: GT62F-B8026 with firmware R3.00 Processors: AMD EPYC 7551P 32-Core Processor Hypervi...

Hello, We have this issue when the LTE connection is bad, the registration stops and goes to "Registration Denied" in the LTE section. Here's our setup: Board: RB912UAG-5HPnD RouterOS: 6.44beta61 LTE: R11e-4G V005 Here is a partial logfile: Jan/22/2019 14:56:43 lte,async,raw lte1: sent AT%...

So, I got this to work for the Cisco phones with: /tool fetch mode=http port=80 url=http://192.168.88.xxx/admin/reboot But I cannot seem to get the Snomphones working, because I cannot type a "?" into the command line as URL... I should use this: /tool fetch mode=http port=80 url=http://19...

So, is there a way to script this into an RB2011?

I'd like to send these commands to internal IP phones

When I browse on my PC to that link of the phone, it just reboots.
So I'd like to know if there's a way I can implement this in somesort of a script.

Well, apparently it works without authenticating. Just browsing to that URL would do the trick, since they're not protected with a password.

Hello, I have a Dual Gateway failover in place, and I'd like to do the following: Whenever the route switches from WAN1 to WAN2 (and the other way around). I'd like to reset my SIP phones remotely. this can be done by browsing to the following URL: http://192.168.xxx.xxx/admin/reboot for Cisco and h...

Nevermind, I got it to work, seemend like I had to use Masquerade for both ethernet1 and ethernet2 to my bridge for it to work

Hello, I've used the failover script from http://wiki.mikrotik.com/wiki/Failover_Scripting Now my problem is that my failover automatically goes to eth2 and doesn't return. My config: # ------------------- header ------------------- # Script by Tomas Kirnak, version 1.0.7 # If you use this script, o...

Hello,

I've followed the guide
http://networkingforintegrators.com/201 ... hcp-range/

but the problem is that I can translate to an adress, but I cannot ping...

I also can't surf. How can I fix this?

Hello, I've just set up my Hotspot using the Hotspot set-up. Everything is working fine, except that the users don't get redirected to the login page when they connect. Like on android you'd get "Credentials required for this network" and on iPhone you'll get the login page automatically. ...