We have the same problem. Not only that the rx-drop counters are rising but we can see the impact on the forwarded traffic.
So far we haven't found any solution other than replacing the affected router with another type (e.g. CCR1009).

Check gateway was not enabled.

Hi, clients on router2 are connected either directly (gateway is on interface on router2) or through static route - this is same as on router1. I don't think, that the problem is on rotuer2, because: 1. When I looked in Winbox to the routing table on router1 all (static) routes to the other router (...

1. All links are wired and networking does not work for unreachable clients (networks)
2. No special configuration on routers - only routing with firewall and traffic shaping

Petr

Any ideas?

All routes are static.

Hi, I upgraded one of our RB600 (Router 1) to the ROS v. 4 (4.4 and then 4.5). After several hours (minutes) it stops routing data to the clients (networks) which are not directly connected to it (with an exception of default route which always works). In the routing table (ip routes) it says that g...

Hi, several weeks ago I installed Dude and set up monitoring of Mikrotik based network. Since that time I have been experiencing difficulties accessing SSH of some Mikrotik routers. In every few days router stops responding to SSH connections. Only solution to that error I've found so far is to rebo...

Any ideas?

Hi, I'm using 2 different RIC/522T PtP links (one with ROS 3.3, other with ROS 3.6), both on distance of 2 miles, and I have following problem on both of them: When there is no traffic passing between ends of link, CCQ is 100%/100% and rate is 54/54Mbit. When I start to send some traffic (even coupl...

Hi, I have one main map (Global) with 2 levels of submaps (City, Building): Global --City ----Building In the Building submap I have 2 devices. When I look at the City submap it shows Building submap with 2 devices and their statuses, but when I look at Global map it shows City submap with 0 devices...

Hi,
I've got server with several ip addresses. On each address there are some services (web, NTP, SNMP, ...). Is it possible to poll this server and all its services as one device?

Thanks.

Petr

If it is not MT problem, then where is the problem?
If I substitute wlan card on MT by WL-5450AP in AP mode connected to MT by Ethernet, network is working correctly.

Any ideas?

Hello, I have some issue with following network configuration: MT Router (R) - wlan in "ap bridge" mode ||| 172.16.1.1/30 ||| Ovislink WL-5450AP (Client mode) (AP1) ||| ||| Ovislink WL-5450AP (AP mode) (AP2) ||| ||| 172.16.1.2/30 Ovislink WL-1120AP with APPro firmware (Client mode) used as...

wait for 2.9.44 version.

Hi,

I upgraded system to v. 2.9.44 and my second problem (double gateways instead of two different ones) is solved now, but the original problem still persists).

Any ideas?

wait for 2.9.44 version.

When can we expect release of the 2.9.44?

Petr5250, Try upgrading to 2.9.43. I know i had a couple OSPF issues with the older versions and doing that fixed alot of things. Matt Matt, I tried to upgrade to 2.9.43 but the problem is still there. Using routing-test package didn't solve the problem either - it was even worse, because networks ...

Hello, I'm using ROS v. 2.9.40 with routing package in following environment. |Master|-----link1-----|Slave |-----client networks |router |-----link2-----|router| There is one Maser router which is connected to the 12 Slave routers. I'm running OSPF between those routers to ensure load balancing and...

The problem is, that script works in 99% of cases, but sometimes it fails to return the value. When I look for the route in output of /ip route print, it is there, but script does not return it.

I'm looking for route. Sorry

To search for existing route I'm using following script: Although searched IP address exists, script returns no value.

Can you help me find the problem? I'm using it on RouterOS v. 2.9.40

Is it possible to change default timeout (15ms) for sending aggregated packets when using ip packing feature?
15ms timeout is sufficient for VoIP but it is too long for on-line games. On-line games are producing very small packets (80-150bytes) every 20-30ms so they are delayed by approx. 20ms.