Hello! I am getting ready to purchase RB960PGS with License 4. I would like to confirm if there is a limit on # of clients that can be connected to RADIUS server with User Manager package? I will be setting up the RB with existing access points at a hotel. Guests will be connecting to a AP with RADI...

@ Rudios

I will look into on configuring your recommendation.

Any idea on where this should be done?

Problem Resovled.

Under the Firewall Rules (NAT)
- I created a new rule for NAT to allow LAN traffic from Bridge 2, which is on private LAN on Port 5.

Hope I did this properly...

Thank You! to "plisken" as well for helping me along the way.

I verified what you mentioned. Still not luck.

Later this weekend I am may remove all configuration and start from scratch.

I will need some time.

I will update you on this.
Sandip

Please see the attached file.

I am able to get the 1.xxx ip however, the internet is not working.
I ping yahoo.com from the router's terminal and it responses.

I am not sure if my NAT rule is correct for Port 5.

Sandip

Hello! I did as you mentioned using the screen shot. However, I am not sure if it's done correctly. I have doubt about the NAT rules on Port 5 and I also, created second bridge. Please let me know... Sandip /interface bridge add l2mtu=1598 name=bridge1 add name=bridge2 /interface wireless set [ find...

reply to @ plisken I followed your instructions (pictures only, I can't read the language) from the links and got the best I could do. Please see the config below and let me know what I did wrong. I couldn't get IP when I had port 5 independent and assigned DHCP to the port. /interface bridge add l2...

@ Benik3 I would like to know how you setup your config. for the Second LAN for WiFi. I just posted a note in forum about implementing a Second LAN for office machines on my RB951G Would you mind posting your config or reply to my forum question. You may omit your information from the config if you ...

I have following network up and running without any problems. However, I would like to add a second LAN with it's own IP address and DHCP server. I scrambled through the forum and couldn't find the exact information I would understand to implement on my router. Someone please inform me about what is...

I have ordered a RB951g-2hnd gigabit ports router to replace the 100mpbs.

Anyone have an ideas how can I move the configuration from the existing (RB951UI-2hnd) to RB951g-2hnd?

Somewhere in the forum I saw that DO NOT use the backup / restore options.

Any suggestions are welcome.

Thanks!

@wurstuam

Sure, you welcome to visit anytime.

The hotel is in middle of nowhere (countryside). Location: Mayfield,KY USA

I ran into some problems too. However, mine I got to work out after and responses/suggestion from the forum. I did however, followed quite few YouTube videos to make sure my settings were correct. This is because I am very new to Mikrotik. These are the links of videos I followed. http://www.youtube...

I worked with the configuration yesterday. After having the similar problem again I deleteed the DHCP entry (second time) from DHCP server and created new one. (Thanks! @Wurstbaum) After that I let the network run for overnight and renew all ip's via UniFi and they seems to work. Yes, indeed I am us...

@ deejayq Yes, I confirmed the IP was 169.254.x.x on more than one devices. @Wurstbaum I will try out your suggestion and let you know. Also, if you could let me know if this RB951 is adequate for a small hotel that would have round 30-35 people logged into the router. Currently, they are using EnGe...

@deejayq Yes, I am very sure that the devices connected via UniFi were getting IP 169.254.1.x. I specifically made a note. @Wurstbaum I will give it a try on your advice and fine tuning. Meantime here's my config. for the Unifi's. The four Unifi's AP's connected (WIRED) has been up and running for a...

Got my first RouterOS (RB951UI-2hnd) setup. I followed couple of You Tube videos to setup the router. However, I got the router to work with Internet access using physical LAN (192.168.0.X) via cable connection only. Here's the setup.... (see the attache config file) Internet | RB951--->Ether 1- WAN...