UP !!

Same behaviour as mine... Only works in channel 1 with 20 Mhz. ROS 6.35.4 with cm2 although i still get strange lock ups in random times.

5ghz works perfectly..

I have a 433GL board with RB52n-M card in 2.4Ghz as an AP. I get a lot of Link Downs (100 per day). What that means?. ROS 6.32.2 but I also tried with 6.34.3 (cm2-package). I also have an identical setup with an extra RB52 in 5Ghz + 2.4 GHz with no link downs.... Is this a hardware problem of the fi...

Would also like to know if a method like the one discribed above, exists...

Στάλθηκε από το Redmi Note 3 μου χρησιμοποιώντας Tapatalk

If i had 2 virtual APs in every AP tagged with different vlan id's and wanted to not "speak" to each other, would this configuration with the split horizon attribute enabled help me to keep the 2 vlans separated? or i must add firewall rules to forbit communications between the vlans? Στάλ...

I am interested at the power level that is "leaving" the antenna.. That must be ~ 16 watts.... right?

Can anyone pls clarify the maximum Transmit power of SXT 2?

As per specs the chip has 32dbm max transmit power and the antenna is 10dbi. So the total max transmit power out of the antenna is 42db=15.85watts?

Am I correct?

Thank you very much for your comments, they were very helpful!

Anyone else with same experience?

Πατρίδα...δες εδώ:

https://support.opendns.com/entries/696 ... ate-Script

Outdoor. The area I want to cover has about 120m radius (I am only interested to cover only 180 degrees, and the 3 APs are 12m above ground) but it is very congested in 2.4ghz band because it has a lot of cafes with their own WiFi spots. Clients are mobile phones and tablets. Currently we try to cov...

Does anyone have any tips for the above configuration? Which are the best settings for a Mikrotik AP in a crowed place, open air space? Does Adaptive Noise Immunity setting help? Which is the best value for Disconnect Timeout? Hw. Retries value? Distance setting for 80m radius of coverage? Hw. Prote...

Remove tkip... Hope that helps..

Maybe another station uses the same address (which is staticaly assigned to station)? Happen to me....

The problem was with the RB532A... i sent it for service and fixed!

Thanks!

/system resource pci print detail 0 device="00:06.0" name="unknown (rev: 1)" vendor="unknown" category="PCI bridge" vendor-id="0x3388" device-id="0x0031" irq=0 1 device="00:03.0" name="VT6105 [Rhine-III] (rev: 134)" vend...

/system resource pci print # DEVICE VENDOR NAME IRQ 0 00:06.0 unknown unknown (rev: 1) 0 1 00:03.0 VIA Technologies, Inc. VT6105 [Rhine-III] (rev:... 143 2 00:02.0 VIA Technologies, Inc. VT6105 [Rhine-III] (rev:... 142 3 00:00.0 Integrated Device Technol... IDT79RC32434 (rev: 0) 140 Thank you for yo...

I just purchased a RB532A with a RB 564 Daughterboard. I installed 2.9.25 an when i issue the following command in terminal window: /interface ethernet print i get: Flags: X - disabled, R - running # NAME MTU MAC-ADDRESS ARP 0 R ether1 1500 00:0C:42:04:AF:59 enabled 1 R ether2 1500 00:0C:42:04:AF:5A...