MikroTik

aresmt

Hi All, would you please help me with this configuration? I have an internet connection through cable on a MK router. On the same router i have : - a subnet on cable 192.168.1.0 - CAPsMAN configured to provide SSID A (192.168.2.0) to various MK APs - CAPsMAN configured to provide SSID C (192.168.3.0...

aresmt

See https://wiki.mikrotik.com/wiki/Manual:Interface/Wireless#Repeater I would not recommend doing this without a wired connection during configuration though. So, is it possible or not what I described? More than that, if you send me to a generic documentation you are not helping me, because I don'...

aresmt

Hi All, Would you please help to configure this routerbord like this: 1. Starting from a clean default configuration 2. Connect the router to another wifi network (non-Mikrotik device; I only have the SSID and password) as a client. This will be the internet connection. 3. Create an SSID which will ...

aresmt

Hi All,

Thank you for your help. I manage to configure fallowing your instructions.

It seems that over OVPN I get low transfer rate.

From router to router I get 60Mbps
Over OVPN I get around 300 Kbps

Certificates are 4096 and MTU is 1500

Any suggestions?

Thanks in advance,

aresmt

Hi Guys,

Any help here?

Thanks,

aresmt

MikroTik A: /ip route add distance=1 dst-address=192.168.200.0/24 gateway=ovpn-interface-name MikroTik B: /ip route add distance=1 dst-address=192.168.10.0/24 gateway=ovpn-interface-name Hi Dave, Still not working. From Mikrotik B (Client) Subnet 192.168.200.0/24 i can ping OpenVPN Local IP (Server...

aresmt

Hi, Would you please help me with this issues that i have. I have 2 Mikrotik routers on 2 different locations and i want to connect the subsets through OVPN. The connections is configured but i have some problems configuring the routes and masquerade. MikroTik A (Server) Subnet 192.168.10.0/24 Mikro...

aresmt

Hi, I accidentally deleted an MAC from an IP-Cam mounted on a very difficult place to reach. My router 2011UiAS-2HnD (Firmware 3.30) is configured to allocate IPs by MAC only. Cam is only wifi connected and router is configured with CAPsMAN. I can cut the power to the IP-Cam. How can i configure the...

aresmt

Set up rules in ip firewalls forward chain, to block or accept whatever addresses you need.

I know that i need to set up an firewall rule, but i don't know how to block that ip to go in internet but in the same time to be accessed from internet via port forward on port 80 for example.

Thanks,
N

aresmt

Hi, Would you please help me with some info? I have an RB2011UiAS-2HnD-IN. these subnets configured on it: 192.168.10.0/24 192.168.12.0/24 192.168.16.0/24 3 separate DHCP servers for each. I just want to prevent specific IPs to go on internet but in the same time to be contacted from internet with p...

aresmt

any advices?

thanks

aresmt

It has to be mentioned that 2n devices have only one chain. Therefore they are not so good for heavy data transfers. Maybe they are good for hotels and occasional connectivity, but not for bigger dayly use on such exposed places. From this point of view comination of 2HnD and 5HacD radios is the be...

aresmt

- one TV/media player will play 1080p HD content from a NAS - another computer will work on files stored online on a local server - other devices browsing the internet 1080p stream from NAS should be 10-20Mbit maximum. Not sure about the others. If you want future proof, I suggest one of our 802.11...

aresmt

cAP and mAP are more than enough for such small room and requirements. please clarify what you think is lacking in those products so we can suggest something appropriate. judging from the requirements alone, I would say that you don't need the specs you outlined Hi, Assuming that: - one TV/media pl...

aresmt

If i need L4 license:

This could be an interesting combination:

- RB912UAG-2HPnD
- 2 x ACSWIM antennas

and an extra for 5GHz:
- R11e-5HnD
- 2 x ACSWIM antennas

+ stationbox inspot

What do you think about this config?

Thanks in advance,

aresmt

Hi, There will be individual rooms with concrete walls that have iron bars in it. The rooms are about 5x5 meters. And the clients will be as usual: phones, laptops, tvs, media players which will play hd content over wifi. Just want to build a capable AP from "parts" at an fair price. I am ...

aresmt

Maybe if you give us some more information? How are these subnets connecting? Wireless, wired, tunnels? You said you tried to configure it. What about posting your configuration? IMHO, do it step by step. First set up one single subnet, after getting it working, add another... I would start with gu...

aresmt

Thanks for your suggestions guys.

Does these antenas http://routerboard.com/ACSWIM
works with RB911G-2HPnD ?

Probably they will fit in stationbox-inspot .

Thanks,

aresmt

You need some enclosure like this: http://www.rfelements.com/en/products/enclosures/stationbox-inspot/ and the rest depends on you. You can put there RB951G-2HnD, for example. Or some 105x105mm board, e.g. RB922UAGS-5HPacD with additional card including big antennas. Thank you jarda. will RouterBoa...

aresmt

Hi Guys, Can you please help me understand how to "build" with Mikrotik boards an AP similar with cAP 2n in size but better in specs? I would like to have: - Gb port, - more dBi on 2.4GHz, - POE in - support CAPsMAN Can you also point me where to find nice enclosures for inside use? Thanks...

aresmt

any help please?

aresmt

Hi Guys,

No advices?

Thanks,

aresmt

Hi Guys, Can you please help me with this configuration? I am not a master in configuring routers but i usually read a lot of documentation before doing something. I have this Mikrotik router and tried (without success ) to configure it like this: 4 separate subnets : 192.168.10.0/24 - PRV, (private...

aresmt

Yes all routerboards with wireless interfaces

Great
Thanks,

aresmt

Hi,

Sorry for this silly question.

Does OmniTIK UPA-5HnD support CAP wifi configuration through CAPsMAN?

Thanks in advance,

aresmt

Hi, I tried with proxy. Probably I am doing something workng, but the proxy is working randomly /ip proxy access> export # sep/07/2014 21:03:44 by RouterOS 6.19 # software id = HK1L-HGDT # /ip proxy access add action=deny dst-host=!:wikipedia src-address=10.0.0.0/19 wikipedia is working; yahoo is wo...

aresmt

... I don't see how can i block or permit services by IPs.... Read more carefully: For know what are the list of all ip assigned to whatsapp, wikipedia and facebook, search on the ripe.net, arin.net apnic.net afrinic.net and lacnic.net Please read hole sentence: I don't see how can i block or permi...

aresmt

Traduction: 0) Traffic on port 53 pass without restrictions. 1) If IP pool of user are from pool 1, block all IP except the address-list of IP pools assigned to Wikipedia 2) If IP pool of user are from pool 2, block all IP except the address-list of IP pools assigned to Wikipedia and Whatsapp 3) If...

aresmt

Hi , I have an HotSpot configured on my RB2011UiAS-2HnD-IN I am trying to create 4 user profiles. One that will only have accesst to: 1. Wikipedia 2. Whatsapp +wikipedia 3. Whatsapp + facebook + wikipedia 4. No restrictions My bigest issue is Whatsapp, i tried all kind of combination, firewall, prox...

aresmt

Hi, I managed to use the CAPsMAN and create 2 SSIDs on both devices. How can i use ACLs only for one SSID? For example: WIFI-Corp to work only on MACs in ACL. WIFI-Guest to work only based on password. MACs from WIFI-Corp to be able to connect on Guest as well if they want. ...and what about that Us...

aresmt

Hi Guys, Does this board RB911G-2HPnD works with this antenna: http://www.ebay.co.uk/itm/60-inch-tall-D-Link-ANT24-1500-Outdoor-15-dBi-360-Omni-Directional-Antenna-/201122615148?pt=US_Networking_Boosters_Extenders_Antennas&hash=item2ed3d78f6c ? Can you estimate the coverage area in a open field?...

aresmt

1. Use "auto" in configuration of channel and each AP select better channel for using. 2. CAPsMAN -> + -> Master Interface (choose your existing wlan interface) 3. If I right uderstood your question - remote CAP save his configuration. 1. can't find auto on Frequency or channel. 2. CAPsMA...

aresmt

For this purposes my advice - use fp-wireless package and CAPsMAN feature. Main router 2011 use as CAPsMAN manager - create 2 profiles for WIFI-AP and GUEST-AP, after that wireless interface use as CAP. SXT use as CAP, enable CAP create the bridge and select IP of CAPsMAN manager (2011). You can re...

aresmt

Hi, I am the happy owner of an RB2011UiAS-2HnD and an RB SXT G-2HnD. The way i have them configured now is like this: RB2011UiAS-2HnD is the main router, with the internet uplink. It runs the DHCP as well. SID WIFI-1 The RB SXT G-2HnD is configured as bridge AP. SID WIFI-2. Network 192.168.10.0/24 W...

aresmt

Yeap,

Cable was the issue.

I replace it with a short one cat5e , 2m , and now it's connects at 1Gb and the voltage incresed to 23.5

almost 4 hours uptime, all modules installed.

btw, is cat6e 100% copper?

Thanks,

aresmt

These are the logs.

aresmt

Oh. You installed combined package. I am not using that, recommend to use single selected only packages instead combined one. :) Ok, What is that? Combined packages :) maybe i am a beginner, but the website is not very clear about it. just downloaded that "Upgrade package" and installed. ...

aresmt

Download 6.19 and put only selected packages you want by drag and drop into winbox. Then reboot. It will install automatically. Maybe other reboot will be necessary. I manage somehow to upgrade it to 6.19 with 3.17. Voltage is 20 Temperature 48. Same cable cat5e 20m. Now is randomly rebooting every...

aresmt

Hi, Eventually i bought this one SXTG2HnD but i have some issues. every few minutes is rebooting. I want to upgred it but i don't undesrtand what is on Mikrotik website. What is 6.19? What is 5.26? What is 4.17? My SXTG2HnD webfig version is 5.26 My SXTG2HnD routerboard Current Firmware is 3.09 My q...

aresmt

Because the field is not big, so devices will work fine. Try to install in the corners of one longer edge and aim them to the center of field. And please post your test results here Hi, just received yesterday an connected to my remote network. I am currently not in the area where the AP is and i c...

aresmt

Hey these are 5Ghz band devices, are you sure, that your customers are using 5G band? by the way, Lites can't work as AP's, Grooves - can. In your case initially i would use 1 groove, and after if it is not enough you can add second device on opposite edge. The max rate, that you can expect from gr...

aresmt

Hi, There are mainly laptops and mobile phones (dell, hp, samsung galaxy s, htc, tablets), now, arround 10. From time to time for short period of time some of the devices need faster transfer rate. Not all of them in the same time. The most accesible place where i can install an AP is arround at 10...

aresmt

Hi, There are mainly laptops and mobile phones (dell, hp, samsung galaxy s, htc, tablets), now, arround 10. From time to time for short period of time some of the devices need faster transfer rate. Not all of them in the same time. The most accesible place where i can install an AP is arround at 100...

aresmt

For first step You can use Groove A52Hn Hi, I can't find this model on the website. Can you please be more specific? or give me a link? Thanks in advance, Found this one: http://routerboard.com/RBGrooveA-52HPn But, How many do i need for that area? What antenna do i need? I would prefer to have as ...

aresmt

For first step You can use Groove A52Hn

Hi,

I can't find this model on the website.

Can you please be more specific? or give me a link?

Thanks in advance,

aresmt

Hi,

Can you please help me chose an outdoor wifi AP from routerboard.com that can provide me coverage on 400mx50m open field that can sustain 60-100mbs fot devices like laptops and mobile phones?

Preferably to have gb port but not mandatory.

Thanks in advance,

aresmt

add action=dst-nat chain=dstnat dst-port=80 protocol=tcp to-addresses=192.168.10.125 to-ports=80 Pretty sure this rule - without defining an 'In' interface or dst-address, will be catching ALL your NAT port 80 attempts and trying to port forward you internally. Remove this rule as a test and see if...

aresmt

any ideas guys?

Thanks

aresmt

Go to terminal. Type: "export" That's it another issue that i have is that when i try to access from INSIDE the lan xyz.mydomain.com it doesn't work, only from outside my network is working. can you also take a look at the firewall rules with port forward for 80 here is the output : # aug...

aresmt

Sensitive data can't be readed.

sorry, can't do that. don't know who decided what is sensitive or not for a specific user

i can post specific outputs if you give me the commands.

Thanks,

aresmt

Post your export file in this forum then can we look what wrong if you can login.

doesn't that file contain users, passwords, and other sensitive info?

aresmt

even with 6.18 is the same root ~: ping forum.mikrotik.com PING forum.mikrotik.com (159.148.147.201) 56(84) bytes of data. 64 bytes from tuncis.mt.lv (159.148.147.201): icmp_seq=1 ttl=57 time=71.8 ms 64 bytes from tuncis.mt.lv (159.148.147.201): icmp_seq=2 ttl=57 time=71.0 ms 64 bytes from tuncis.mt...

aresmt

What RouterOs?
Have you add firewall rules?

3.18
no rules than default rules which come with the default config

thanks

sorry, it was 6.17, was specified in my first post.

Just upgraded to 6.18 now

aresmt

What RouterOs?
Have you add firewall rules?

3.18
no rules than default rules which come with the default config

thanks

aresmt

Maybe UPnP is on and some local service trying to use it?

Just checked, UPnP is not enabled.

aresmt

HI, I have 2 RB2011UiAS-2HnD-IN router. One of it is in a remote location which i don't have physicaly access very easy ,only remote connection. This one, has an strange behavior, or maybe i don't know how to use it. From time to time it starts to block port 80 when i try to connect from his lan on ...

aresmt

Seems you believe that radio waves will be waving according to your personal attitude. Please keep us updated how it goes. i am pretty sure that the radio waves will not be waving to my personal positive attitude, but if i would had experience and knowledge in wifi, i would respond to this post lik...

aresmt

ok, someone else with a more positive attitude?

Thanks,

aresmt

I understand that they want wifi inside the houses. But do they care how you deliver the connectivity to their houses? If yes then you would need to make ptp link for each individual house to be able to guarantee the speed. But the band is not wide enough to host so many links too close each other....

aresmt

Optics would be a solution, BUT, the customers wants WIFI

, They already have UTP at 100Mb, they are not happy with cables, they want WIFI.

That's why i posted my question in the wifi section asking about an wifi solution.

Thanks,

aresmt

If you really want to reliably deliver such speed for all houses along the street you should dig deep down the optic. I also wonder how you could bring at least 10gbps uplink to such area. Maybe more would be needed if you connect more than 100 houses. Hi Jarda, Let's focus on wifi, forget about my...

aresmt

Hi, I would like to create an hotspot network with Mikrotik equipment, but to be honest, I don’t have to much knowledge about wifi. Maybe someone of you can help me to choose what do I need from Mikrotik products. The area where I would I to implement this is a straight line (described like this): -...

aresmt

Hi, As i said in my previous posts, i am not an expert in this. I have an "issue" or probably i don't know how to configure it properly. I have an RB2011UiAS-2HnD-IN. I am using it DHCP from my ISP. It is also configured with my account on dyndns, something like : test.mydomain.com On the ...

aresmt

If you want to cover blank places of your flat, use other ap connected to main router by cable. It will be much more efficient than making antennas bigger. Otherwise explain in details what your goal really is. I have perfect coverage in the house, except the balcony (after i close the door). I don...

aresmt

Hi, I am the owner of two RB2011UiAS-2HnD-IN routers. I would like to "upgrade" the antennas but i don't know to much about wifi. Can you please advice me what kind of antenna should i buy? In router's specifications says: Antenna gain DBI 4dbi TX power 30dBm what would you think about : 2...

aresmt

Hi, I tried to configure my router (RB2011UiAS-2HnD-IN) to accept connections on port 80 or 8080 for the webfig. At a certain point i realize that because the default DROP rule was before that accept rule for input on port 80 or 8080 on the wan interface the router didn't accepted the connection for...

aresmt

Use scripts:

http://wiki.mikrotik.com/wiki/Dynamic_D ... for_dynDNS

Thanks,

That worked great.

aresmt

Hi, I recently bought an RB2011UiAS-2HnD-IN. I updated the software at 6.11. I am trying to configure the dyndns with an account that i have on dyn.com According to the manual the settings should be in Tools / Dynamic DNS but i cannot find this anywhere. Can anyone help me with an advice? Thanks in ...

Search found 68 matches