Ok so I realize that If I connect A router to the modem then I shouldn't have to fool with much. the router should assign the laptop connected to that router a ip, then I just have to make sure the radio thats connected to the router is properly programmed? What should I set the Radios WDS to thats ...

I just realized that my radio is plugged into a Linksys Router! So why must I do all this nat etc,,,? Why does the linksys Router not assign the MikroTik Radio an Ip? How could I configure that inside the Mikrotik radio to accept whatever Ip the Linksys Router give it? I'm starting to realize that M...

You are probably switching / bridging everything. But you have to implement nat with masquerade just behind the modem because you have more devices than your isp is willing to assign ip addresses to you. Sounds like a plan! so how to I learn hot to implement nat with masquerade? Sounds like thats w...

Nobody does not know? I assume I will set up a DHCP on my Radio A and set Radio B as Dynamic in this case. Where are the techs on this forum?

I do not understand the first reply, I thought this was a mikrotik only forum? I'm sorry i'm not that bright here :/ My radio is connected to a switch, the laptop is also connected to the same switch. Works great! the ISP moden is also connected to the same switch, works great! Problem, when Laptop ...

I Need help, I do not know what to set my radios on. I use a ISP that uses a DHCP to give me an IP. I then connect that modem to a switch, then to a radio, and also a Laptop. I am having issues getting it to work. I assume its an IP problem. To this minute, The Radios are set to Disabled. What shoul...

Be aware you can click on the Mac Address using winbox, Or the IP address. Whichever you click on. Also you might need to change your network sharing center connections. See http://forum.mikrotik.com/viewtopic.php?f=13&t=84903 on that. That can indeed effect it. Else, Reset your router and start...

You need to learn how to use CMD, command prompt to find the IP of your DVR. You can see how I do it here. http://forum.mikrotik.com/viewtopic.php?f=13&t=84903

You may need to change some Network Connections to get there as mentioned in that thread in order to find that ip.

I hope this will help you. http://forum.mikrotik.com/viewtopic.php?f=13&t=84903

To you that is looking at the Mikrotik Operating System or even dont know how to get into the system, This thread is for you. If there was such a thread I could not find it, I assume others cant either. BTW, I can be in the isle with soap and not see it! This is a attempt to target getting into goog...

Well, i'm now at my second location! Yaaaay! But, I test my signals without a antenna connected, how else do you do that on a desk? I honestly dont know, and it is the only way I know how to learn and test. I really dont want to be sandwiched between 2 microwave ovens LOL. I now have 2 Level 4's on ...

It wouldn't work with the top screwed on. So I was playing around like an idiot with my fingers and I got full signal. After about an hour I learned that If I turned Chain 0 OFF and Chaing 1 ON then clamp the connector to chain 1 not chain 2 then the signal was 100 percent! YES, is it possible a cha...

Well Now I'm not so sure guys. I put the parabolic on the antenna and walked away with laptop in hands, I get nothing! All chains are checked. IT only works on the desk of the Top cover of box is taken off Radio. If I put the Box together I drop a bar. Its like the antenna is doing nothing. Maybe th...

Thanks for your input guys. I purchased 2 RB711 2Hn both with level 4!

Im currently on my laptop posting this thread via wifi! Using the RB711 AP Bridge Now! It isn't connected to an antenna. I assume the Client Board Bit the dust.

How stupid? I just realized if I buy a high level license board then It would work with something I have right? one or the other! Wouldn't that be a solution?

Thank you for your reply, And No I don't. I'm new to this and I only have those 2 boards. The AP Bridge has 4 chains I think, I assume thats the 2 Brass Miniature antenna connectors. My Station Has 2 chains I think, just one Brass connector for Parabolic Dish. I am Not wanting to switch to another P...

I have a RB711 AP Bridge and Station. One of them is bad! Looking at the AP Bridge Boards Registration/Signal Tab I can see the Station at -30s Looking at the Stations Boards Registration/Signal Tab, I can see the AP Bridge at -89 I have both connected to a 24Dbi parabollic dish. Question, Should I ...

Hi, I No noting about any of this at all! I am Lost, Dumb and been working on this hours! I will start with what I have. 1. I have a RB711 AP Station!! (Higher Level) AP Yaaay! 2. I have a RB711 Station! (low level License.) Client only. Here is what I have right this moment. I have a WildBlue Conne...