Thank you very much, it is working rightly as you said

I have a router 750Gr3, which I am using as a Switch Ethernet. All ports have been added to a bridge, which has "Fast Forward" functionality disabled. I only want to allow two MAC sources address to comunicate through this Router (configured as a Switch). It is the cibersecurity requiremen...

Sorry but it is very dificult for me to configure it in a V7.3.1 I have a router with 3 Interface: - Interface ETH1: Host with IP: 172.22.x.x/16 and host with 172.23.x.x/16 - Interface ETH2 (192.168.1.1/24: Connect to Firewall1 (192.168.1.2/24) - Interface ETH3 (192.168.2.1/24: Connect to Firewall2 ...

How can I check what are the routes advertised by BGP???

I can not configure everything in a lab. I have to do right now and I do not find how to see what are the network adverised in order to know if it is working.
Please, anyone can share with me the command.

OK, thank you. I have implemented those commands but I do not find how to see what are the network adverised in order to know if it is working.
Please, can you share with me the command.

I have V7.5 and I am a little confused regards BGP output filter. I have a router with a lot of subnets but I only want to publish (172.23.54.x/24) 0 chain=BGP_Filter rule="if (dst-len>24 && dst in 172.23.54.0/24) {accept}" Besides I have configured the BGP as follow: name="bg...

I had exactly the same problem as giulianoz.
I opened the WAP LTE KIT and I found out that antenas were not connected to the LTE modem, increible

ok, perfect. I have done an EoIPV6 and it works fine. This tunnel pass even the MAC address so we have a "cable" between two IPV4 branch through an IPV6 network.
How is it posible to cipher the tunnel??

I have two IPV4 networks separeted by an IPV6 network.
How can I do to comunicate between IPV4 networks through an IPV6 network?

Is it posible to convert from multicast to unicast with the RB750GL?
I need to convert from 10 multicast group to one IP unicast

I have an EoIP tunnel + PPTP with two RB750GL configured without any filter.
Why does it drop Ethernet packet whith MAC DESTINATION: 01:80:c2:00:00:0e?

I have done an EoIP over a PPTP as it is specified in the following link: http://blog.butchevans.com/2008/09/mikrotik_routeros_transparent_bridge_pptp_eoip/ Everything is running fine, the problem happens when I carry out the RFC2544 (bidirectional) test in order to know the throughput. I am spying ...

How is posible to activate ARP GRATUITOUS in every Ethernet interface?

CISCO supports The Network Address Translation − Port Translation (NAT−PT) is an IPv6 to IPv4 translation mechanism, which allows IPv6−only devices to communicate with IPv4−only devices and vice versa. NAT−PT is designed to be deployed to allow direct communication between IPv6−only networks and IPv...

It is very easy to drop packets because I remove the Ethernet cable during 3 seconds aprox. and once I connect it again the packet lost it shows 10.000 packes lost (for example), and when the test finishs it shows 0 packet LOST, how is it posible it shows 0 packe lost if during the test it has been ...

The problem is not the pipe because I have connect with a straight cable. I am working in my desk before going to the customer. The problem is that packets have been lost during the band with test but when the test is finished it shows 0 PACKETS . Why it does not show all the packets that have been ...

I have done a bandwidth test between two Router Board 750 GL (ROUTER OS 6.7) during 60 seconds. I have checked that a lot of packets have been lost during the test but when the test is finished it shows Lost packets=0. Why it does not show the total packet lost? /tool bandwidth-test 40.1.1.1 duratio...