Hey thanks for the response mistry7 It is posible that the house infront of the antena does not clear the fresnel zone. But it shouldnt be by alot.. Any how i might just try to raise the antena a couple of feets and see All chanel look like they are free. When i do the frequency scan. I almost never...

Hey guys, Somewhat new to MikroTik equipment used SXT5 AC lite SXT5 HG ac I have a problem that i think is wierd. I see online that the sxt ac's have a -72db requirement for ac speeds Im getting around -62, Signal to noise of around 40 yet i only can get around 20/20 CCQ, therefore i get a terrible ...

What do you mean by not relevant ?
I still need some help and I posted in the general section.

I guess my question isn't clear. What im asking is what step should I take to figure out where my problem is.

Actually I just realized that when im doing speed test with UDP instead
I get alot of pakets lost receiving but only on receiving from the Qrt-5

Could this be caused by distance of my rj45 cables?
This is speed test my router <-> qrt-5 (10.0.254.9)

Hey peoples. I created an P2P Link with two QRT-5 Connection between the two is excellent I think Registration.PNG When im doing a speedtest between the two of them Im getting 50/50Mbps and 130~Mbps Send/Receive single way SpeedBoth.PNG But when im doing a speed test between my router and my locatio...

You need to clear the trees if you want 400 megs. Build a small tower and then anything will work.

If im building a tower then, what wireless system should i get,

will two of these http://routerboard.com/RBDynaDishG-5HacD works ?

Hi, Id like to have some tips of experienced users of point to point wireless system. First off I have a distance of 1.28KM between to link. I need to have a link faster than 400mbps One point is my home and the other is my work place. Capture.gif There is trees in sight also What wireless system sh...

Now I just tried to do this with PCC method Still no luck help Anyone :? PCC method config ( i removed one local network ) /interface ethernet set [ find default-name=ether2 ] name=Lan1 set [ find default-name=ether3 ] name=Lan2 set [ find default-name=ether4 ] name=Wan1 set [ find default-name=ethe...

Hi peoples. Im getting 2 new connection, And I wanted to "try" a config before the guy come here and install both connection so it can be done in a few min. For easy understanding, I will be using testRouter for the router im trying to do load balancing on and just router for the main rout...

Actually I want to block some end users on the network that are sending email For some reason in the last month multiple end users "Opened an attachement" that made there computer start sending those attachment to all users in there contact list. What i want to do is to block those so they...

I don't have a lots of experience playing with mikrotik, but is there a way I can mark the connection, then filter connection instead of packet? or thats something not possible ?

Or simply how can i achieve what im looking for ?

Hi, I was trying to drop packet that the destination port was 25,465,587 if limit=4/1m,4 those are my rules chain=forward action=drop protocol=tcp src-address-list=EmailSpammer dst-port=25,587,465 chain=forward action=add-src-to-address-list protocol=tcp address-list=EmailSpammer address-list-timeou...

Yeah every IPs are connected to the right port. Also I did go see every of these computer and they are correctly setted up as dhcp, and they all have ip of there own network and the gateway is setted up as 1.1 For routes I think they are okay since from all IPs that i can't ping, They all seam to be...

No, All machine are dynamic except mine and 5 other, Those who are static are from 3.100-3.106, I am 3.101 Also, I did the snifing, It look like there is no route, Or that the packet is just being drop ping 1.20 from 3.101 ( this ping work ) Capture.PNG ping 1.12 from 3.101 Capture2.PNG ping 1.41 fr...

Okay, now I updated my config like you said. But I still have that ping issue It is very very weird to me :? For example I can't ping 1.12,1.41 or 1.111 and when I am connected to the same interface as these I can ping all these. Same thing for tracert If i tracert any of these address I have the sa...

Make sense. I will try that configuration tonight actually. I did all that configuration not very knowing what I was doing and only by looking at PCC example that people was referring to me Could you explain what does the following rules though? fliter forward: allow connection state established all...

Oh I simply disabled it, so I can try the old rules I had. and tweak.

Okay,. :? Now,. For some reason from a device on 1.* I can ping any devices on 3.* But can't from 3.* to 1.* I seriously don't understand anymore.. :lol: These is my current config now /ip firewall mangle add action=mark-connection chain=prerouting connection-mark=no-mark \ in-interface=Bellnet_ISP ...

Hey, Thanks for your reply! I did what you said, Duplicating routes and marking them with routes mark but it does not seam to work Now instead of leaving for internet it just request time out Capture.PNG Just to be sure this is what I did Capture.PNG Also, I how could I make mangles rules not mark i...

Hi, I am out of idea.. I have two network 192.168.1.0/24 and 192.168.3.0/24 One is on ether=4 and the other on 5 Im trying to have a route that will route trafic so both network can be "pingable" Im posting my config, hopping someone can help me cause I don't know what do to anymore. Also ...

See PCC . The basic idea is that you "route" (as in "/ip route") based on a routing mark that you place before routing. Regardless of the result, you srcnat (or better yet - masquerade) both marks. Thanks for you reply. I just read.the PCC article, and im not so sure still how t...

Hi, I am fairly new to the mikrotik comunity, and for this problem I did search a lot online but unfortunately I can only find some awnsers on how to load balance with the two wan, This is not what im trying to do. I have two isp. both isp are PPPOE One has a static ip, I have two network 192.168.1....

Yea the port look dead,..

Is it frequent that port died ? Like I said I had the router for about a week now,.

Thanks for your reply, I upgraded my router to 6.13 this morning but still get the issuie. And port is not disabled or at least that I know off. How can I see if port is disabled ? If I go in WinBox and go in Interfaces I see Ether1 in black font colour and it not gray is there any other place I sho...

Hi, I have an RB951Ui-2HnD ( http://routerboard.com/RB951Ui-2HnD ) It has 5 port on it. It is runing on version 6.0rc14 I had it for about a week now and the first port was working fine. But at some point stoped working, I still see the interface in WinBox but if i plug a cable in it I will never be...