MikroTik

SWISSSNOW

Wireguard with 2 WAN Interfaces - having 2 WAN Interfaces with public IPv4 Adresses (here Cable and Starlink) - connect to Wireguard independently of each other - having one of the WAN Interfaces as a default gateway (here Cable) Coincidentally, I configured this for a few hours with all my experien...

SWISSSNOW

Hello! HELP - because we haven't seen this as a problem for years: We have SNMP polling times of 200-220 seconds on a Mikrotik router (CCR2004-16G-2S+) with RouterOS 7.14.1 (Level 6). This is very long. In fact, only 4 interfaces are specifically queried. We use Observium for retrieval. On around 50...

SWISSSNOW

Thanks for this report. Yes, it's not really a Mikrotik thing here, but I tried to push the experiences from users with expert knowledge and experimental spirit. If you use the actual Standard Dish it comes with the combination "Router-with-Power-Injection" so you have to split out the Eth...

SWISSSNOW

I'm running a Mikrotik RB3011 with direct IPv4 behind an 2nd Generation Starlink (Standard), not unsing the Starlink Router. With IPv6 everything runs ok. Advertisements internal, using clients to internet - full service. Another older Starlink 1st Generation (round dish) get's IPv6 too, but the def...

SWISSSNOW

Hallo! Wir haben bei einem Betrieb des CAPSMAN unter 7.8 mit den provisionierten WLAN Interfaces Probleme bei der Erst-Verbindungen und der Performance. Zuerst sind wir umgestiegen auf "local forwarding", was die Datenraten erheblich verbessert hat. Weiterhin bemerken wir jedoch, dann beim...

SWISSSNOW

Hello Support and others ! We are driving CAPSMAN with 6.49.7 (on CCR1009-7G-1C-1S+). In the past we connected RBwAPG-5HacD2HnD (wAP ac) with same RouterOS using the Certificate request and defined a Discovery Interface. These AP were listet with MAC Adresses. Others, not configured with "Disco...

SWISSSNOW

Hi !

Here the question: I have a custom config - how to get it the fastest way on a new device ? How to manage about 300 "wAP ac" to get the config ?

Grüße
Stefan

SWISSSNOW

Solved:
1. removed Mangle Rules - only testing
2. set up fasttrack connection in fw rules !

SWISSSNOW

But it seems many users like to live on the edge and do not like safety measures... Yes. Thats the right way. Unplug und rollback. And plan using fall-back ! But: undicussed here - where is the solution with using "stable" und why is this harware (an some others, see bug reports) still no...

SWISSSNOW

You can solve it rapidly. The problem born if for some reason on first boot the BIOS swap the PCI ID... Already done for another user: /interface :foreach item in=[find where type="ether" or type="wlan"] do={set $item name="$[get $item default-name]-tmp"} :foreach item...

SWISSSNOW

/interface ethernet set [ find default-name=ether9 ] name=ether1 set [ find default-name=ether10 ] name=ether2 set [ find default-name=ether11 ] name=ether3 set [ find default-name=ether12 ] name=ether4 set [ find default-name=ether13 ] name=ether5 set [ find default-name=ether14 ] name=ether6 set ...

SWISSSNOW

Why not wait some weeks or to first read forum before blindly apply an update just released without testing it first on some spare parts? In this case we learned: stable may be stable, it maybe only testing or lab, maybe buggy for only one device and some use it after weeks ... so stable is also QA...

SWISSSNOW

Sounds like auto upgrade...correct?
Have you missed the WARNING: Do not use this version on RB3011 devices which has SFP port connectivity.?

Yes, our Auto Updates on so much devices do read before working. Would be nice to include such "not working" breaks in the Update itself.

SWISSSNOW

Hello, this night some "RB3011UiAS" chnaged by script to 7.3 - after that all "RB3011UiAS" with an SFP "S-35LC20D" on it were hanging in an boot-loop. Only with pulled out SFP the "RB3011UiAS" came up. We rolled back to 6.49 and there everything is fine. I thi...

SWISSSNOW

after install 7.3, upgrade also on system routerboard the bootloader,

Allready did, mentioned it with "(+Board)" ... did not change. Is it a known bug?
No cables to swap problem. How can this happen ?? On other "CCR2004-16G-2S+" in same delivery evrything is ok.

SWISSSNOW

Hallo, we just unpacked a new CCR2004-16G-2S+ - the Ports are on the wrong side ... Port 1-8 ars 9-16 in RouterOS (9-16 > 1-8) :shock: Is this a hardware problem? Port Banks are directly on the Board placed. Can it be solved by any CLI software command ? Updating to 7.3 (+Board) did not solve. Grüße...

SWISSSNOW

Thanks, we invoked RMA.

SWISSSNOW

Hello,

we just unpacked 4 new CCR2004-16G-2S+ - one of 4 runs Fans permanent >7800 RPM from start and cpu temp is >70C. Is this a DOA ?

Grüße
Stefan

SWISSSNOW

Rollback done.

SFP S-3553LC20D works NOT on 7.1.3 with

exemplary:
960PGS
CRS112-8P-4S

but with 6.49.4 again !

Grüße Stefan

SWISSSNOW

Hello!

We will try to roll back. I'll give you a feed back about it ...

To Mikrotik Bug Report:
We have rebuilt the setup in our lab.
This behaviour is everytime the same on different Harwdare: SFP S-3553LC20D is not working with 7.1.3 !

Grüße Stefan

SWISSSNOW

hEX PoE (RB960PGS) Problem after 6.49.4 > 7.1.3 with SFP Hello! We have a hEX PoE (RB960PGS) with 6.49.4 (+ Firmware) running with a pair of S-3553LC20D - other side is RB3011UiAS. Both sides up, both sides show all values ... running well without any problems. Then we ran the Update on both sides. ...

SWISSSNOW

# model = RB3011UiAS # serial number = xxx /interface bridge add admin-mac=xxx auto-mac=no name=bridge1_LAN add admin-mac=xxx auto-mac=no name=bridge109_JUGEND add admin-mac=xxx auto-mac=no name=bridge170_GAME /interface ethernet set [ find default-name=ether1 ] advertise=1000M-full comment=WAN1 se...

SWISSSNOW

Hello, working with an RB3011UiAS-RM with RouterOS v7.1.1 (same Firmware) I can't find the bottle neck - it's too slow ... The Internet Access is a DOCSIS Calbe Modem with fixed IPv4-Adresses to the inside (LAN). When I connect directly with my Apple Notebook, using the public IPv4 I get a download ...

SWISSSNOW

As already mentioned earlier here, Mikrotik 11ac products do not support anymore non Wifi standard channels (10Mhz or 5Mhz). On the product page it is mentioned support 11a/n/ac, so why would the product offer something else? Thanks for the information, I just was not around earlier here. Can't fin...

SWISSSNOW

I remember that 10mhz channels wasn’t supported with ac Hardware.. Ok. Would be nice to have a matrix with working channels und bandwith beside the RouterOS given options. It's a little confusing if options given in the CLI or GUI are leading to 'not working'. Is there an official mikrotik moderato...

SWISSSNOW

Hi !

When I drop "/interface wireless info allowed-channels" on the CLI I get:

> /interface wireless info allowed-channels wlan1
channels:
> /interface wireless info allowed-channels wlan2
channels:

What's wrong ?

SWISSSNOW

Hello, I'm using the IPQ4019 on RBD22UGS-5HPacD2HnD (mANTBox 52 15s) with v6.48.1 (same on board). I like to use special frequencies licensed for HAMNET. Mode: station bridge Band: 5GHz A Channel Width: 10MHz Frequency: 5735 Frequency Mode: superchannel Country: no_county_set Installation: any But I...

SWISSSNOW

Hello!

Can I support "Automatic Laser Shutdown" using Mikrotik SFPs with Mikrotik RouterOS Hardware?

Greetings
Stefan

SWISSSNOW

Hello ! Is it possible to connect via L2-Tunnel (with EoIP) two IPv6 Bridges via IPv4 from one Router to another? One side has fixed public IPv4 und IPv6 with /36 IPv6 Network and the other side has only fixed IPv4. Are there more elegant ways to get IPv6 to the other side (without native ISP IPv6) ...

SWISSSNOW

If you tried netinstall the right way and is not working, there is nothing you can do.

Maybe I can buy a new small cat and built a littel house for it out of the "box" ...

I will get an RMA# for it and start with a new one.

SWISSSNOW

Your CAT has cable?
Return the unit.

Thank's Dr. Dolittle. I got a RMA# for the cat.

But what about the mikrotik PowerBox - any idea ?

SWISSSNOW

Hello! The Mikrotik PowerBox (RB750P-PBr2) is not comming up after upgrading the RouterOS. I dropped the MIPSBE 6.34.1 (Current) in the File Area and pushed "Reboot" via Winbox. After Reboot 10 minutes nothing happened. No interface comes up an der LED "ACT" turns from "off&...

SWISSSNOW

... community far from my problem ??

SWISSSNOW

Well - so far no one answered - we solved the problem. Contact, if someone likes to know ...

SWISSSNOW

Hello. I want to "IPSec from Mikrotik Router (1) behind other Router (2) with NAT and dynamic IP to Mikrotik Router (3) with public fixed IP" ... I have one Mikrotik Router (1) that's inside an existing LAN, the LAN is behind an existing Router (2) that has NAT to the WAN Interface with dy...

SWISSSNOW

Hello ! We have some problems with OSPN interfaces configuered to pptp interfaces. Somtimes the pptp interface drops, the configuration drops and comes up with the default settings. But we need as "network-type" - "nbma". So I tried to find out how to get the status and set it wi...

Search found 36 matches

Re: Wireguard in 2nd WAN [SOLVED]

SNMP on 7.x appears slower and slower ...

Re: Starlink IPv6 Gateway broken ...

Starlink IPv6 Gateway broken ...

CAPSMAN and MAC Adresses on Subinterfaces ...

CAPSMAN, Certificate, Discovery Interface

New Device with Default Configuration - Fast way to get own config on it ...

Re: RB3011UiAS-RM - max. 240 Mbit/s [SOLVED]

Re: RB3011UiAS with 7.3 - Problem in SPF ! [SOLVED]

Re: CCR2004-16G-2S+ - Ports wrong side ... [SOLVED]

Re: CCR2004-16G-2S+ - Ports wrong side ... [SOLVED]

Re: RB3011UiAS with 7.3 - Problem in SPF ! [SOLVED]

Re: RB3011UiAS with 7.3 - Problem in SPF ! [SOLVED]

RB3011UiAS with 7.3 - Problem in SPF ! [SOLVED]

Re: CCR2004-16G-2S+ - Ports wrong side ... [SOLVED]

CCR2004-16G-2S+ - Ports wrong side ... [SOLVED]

Re: CCR2004-16G-2S+ - 2 Fans permanent >7800 RPM [SOLVED]

CCR2004-16G-2S+ - 2 Fans permanent >7800 RPM [SOLVED]

Re: hEX PoE (RB960PGS) Problem after 6.49.4 > 7.1.3 with SFP S-3553LC20D [SOLVED]

Re: hEX PoE (RB960PGS) Problem after 6.49.4 > 7.1.3 with SFP S-3553LC20D [SOLVED]

hEX PoE (RB960PGS) Problem after 6.49.4 > 7.1.3 with SFP S-3553LC20D [SOLVED]

Re: RB3011UiAS-RM - max. 240 Mbit/s [SOLVED]

RB3011UiAS-RM - max. 240 Mbit/s [SOLVED]

Re: HAMNET Germany [SOLVED]

Re: HAMNET Germany [SOLVED]

Re: HAMNET Germany [SOLVED]

HAMNET Germany [SOLVED]

SFP - Automatic Laser Shutdown [SOLVED]

IPv6 via IPv4 L2-Tunnel with EoIP

Re: PowerBOX down after RouterOS Update ... [SOLVED]

Re: PowerBOX down after RouterOS Update ... [SOLVED]

PowerBOX down after RouterOS Update ... [SOLVED]

Re: IPSec from Mikrotik Router behind other Router with NAT and dynamic IP to Mikrotik Router with public fixed IP [SOLVED]

Re: Get the network-type of an OSPF interface and set it to ... [SOLVED]

IPSec from Mikrotik Router behind other Router with NAT and dynamic IP to Mikrotik Router with public fixed IP [SOLVED]

Get the network-type of an OSPF interface and set it to ... [SOLVED]