MikroTik

ahteran

There is a short circuit part on the PCB BOARD.

ahteran

https://download.mikrotik.com/routeros/ ... c-7.10.zip

extract and use only wifiwave2

The card unfortunately seems not to be recognized due to its driver.

ahteran

You have installed the wifiwave2 package?

No, my friend, I did not install it. can you give me the link please

ahteran

I am trying to use compex WLE650V5-25 (Qualcomm Atheros QCA9888) on RB800 (ROS 7.10 and Firmware same), but RB800 does not see wifi module, what could be the problem?

ahteran

Unless there is some specific limitation in wifi2 package, I don't see any reason why this would not work. You probably could even use mining pci-e riser and run multiple cards off that slot... at least I tried it some time ago with RB800 and all cards were detected and usable... On RB800 Which car...

ahteran

The "compare" tool stopped working on the Mikrotik website, at least today. https://mikrotik.com/products/group/wireless-systems (Useful links: "Product Matrix" could be used) If you compare check wifi type "n" versus "ac", license level 3 versus 4, and ether...

ahteran

Have a ressurected CCR1009 on the desk and was wondering the same thing. Purely computational wise, RB1100AHx4 is light years ahead of CCR1009 Bandwidth test on 127.0.0.1 for both I think shows that CCR1009 CCR1009.png RB1100AHx4 1100AHx4.png Also note that the CCR1009 was blank, without any firewa...

ahteran

Hi, now I've tested with a couple of cables (different manufacturers), which can initiate 1000Mbps via other interfaces (e.g. 4 or 6) and connected to ETH0 my notebook. I still can see maximum 100Mbps via ETH0. When the same cable and the same notebook is connected to ETH3, I see 1000Mbps. So, ISP ...

ahteran

It's hard to get these speeds in the field, but it's not impossible.
What are devices?
What is the ROS version?

ahteran

Which model of Mimosa do you use?

ahteran

I had a similar issue with RBM11G and R11e-5HacD. Now 6.46.8 installed and no problem

ahteran

Change CM9 card

ahteran

Cpu or nand problem

ahteran

Short circuit

ahteran

Hello Thanks for reading and answering. I have tested with 40Mhz, the speed only increases a few megabytes. even, the upload speed decreases. CCQ percentage is also affected although the log table reaches really high values. I do not understand why I do not reach the limit of 100Mbps. Thank you ver...

ahteran

I don't understand which wisp 802.11 uses on MikroTik?
The protocol you should use is Nv2

ahteran

Yes working SXT 5AC No Problem.

ahteran

What should I replace؟
i replaced lan ic. but Problem not resolved

AR9344?

ahteran

Use nv2 or nstreme

ahteran

in the 6.41rc there's a new feature !) wireless - new driver with initial support for 160 and 80+80 MHz channel width; and indeed MT will have its first wave2 device, the next gen cAP with IPQ4018 (https://www.qualcomm.com/products/ipq4018) that has mu-mimo support in hw. the device received FCC ap...

ahteran

Hard reset 1-4 or 2-3

ahteran

We are checking that the new CCR1036-8G-2S+ devices come with dual power supply. The voltage of these is now 12V, previously like the other CCR1036 was 24V. We use centralized 24V DC power supplies and place this accessory: https://shop.meconet.de/Power-Supply/up-to-48-Volt/DC-conversion-kit-from-A...

ahteran

Use nv2

ahteran

You should try with another poe

ahteran

My M11G with Lede/ Openwrt and Ath10k performances much better then with Ros! Can you share any results? The same configuration with LEDE and with ROS? They are installed with Wave 2 PCIE Modules from Compex Next time I prepare new ones I will try Mikrotik AC modules too Compex wave2 work in router...

ahteran

3 km from all users? How long can you look at the timer? Opening for wireless>registration It's TDMA time size as in the image., The only thing I think of is this, it's interference, but I have two basebox's, they're in a location in my tower, they just have them and other radios from other vendors...

ahteran

wave 2 work in the new RouterOS update? IPQ4018/4019 in the new arm devices (sxtsq, hap ac2, disc lite 5ac) is wave2. support for 160MHz channel and 80+80mhz is there. No no the situation is different.. There is at WLE650V5-25A compex card to be used on the RB800. But it does not show the RB800 card

ahteran

wave 2 work in the new RouterOS update?

ahteran

Any updates on this?

QCA9984 supported in ROS yet?

And QCA9888

ahteran

716Mhz

ahteran

Which Mini-PCI card do you use?
Did you overclock the RB435?

ahteran

RB800 is a good choice very fast and stable
You can use R52Hn or SR71-15 or F50N-PRO Mini-PCI
Another good choice is SXTG-5HPnD-SAr2

ahteran

Hi,

here you can see an working TDMA with 802.11ac Hardware.
Good and stable Speeds, low latency,
Mimosa C5c, 20 Mhz

What is AP Model?
A5-14 or A5c?

ahteran

First. I'm sorry for the English.I have a problem that I can not get through.I am trying to install ROS using netinstall and putty with RS232 and ethernet interface.The upload is successful. But when I reboot, the situation is still going on.Each time the green led flashes in the video. I have two ...

ahteran

I have updated RB433, RB450,RB600A, SXT 5ac
No problem Working fine.

ahteran

Try and play one card only
there may be interference because the cards are stacked

ahteran

Distance away, reduce distance due to antenna gain.

ahteran

I've never seen a 15dbi antenna that worked better than 8dbi.

Best antenna in 15 dBi, D-Link ANT24-1500
it is excellent.

ahteran

Yes connect (802.11)
Which radio card do you use?

ahteran

Upgraded 6.38.5 to 6.39
No problem on RB450 and RB433

ahteran

change wireless card
to use r52-350

ahteran

Any idea?

Sent from my H60-L04 using Tapatalk

Where are you from?

ahteran

RocketM2=28dBm rf output power; fast ethernet; 400Mhz Cpu
Basebox2 (912uag)=30dBm output; gigabit ethernet 600Mhz Cpu

Your decision

ahteran

Yes, The device license is not enough (Level3)

ahteran

Not in the picture Ram
It is a Flash

ahteran

bad gigabit poe issue

ahteran

Hi guys I think there are two bug, version 5.26 of the system works as gigabit and in the 6.30.2 version works Fast Ethernet see picture please http://s1.postimg.org/3sae0vcyn/wlan_power_issue2.jpg Another problem an with wireless tx power issue Unex CM10HP wireless card available on RB800 as in the...

ahteran

What is the mikrotik model

Board ''922UAGS-SHPacD''

Search found 48 matches