interface wireless wmm-support=disabled in both ap and cpes, but still shows wmm enabled in registration. how do i disable it?

/ip route add gateway=gateway1ip distance=1 comment=WAN1 add gateway=gateway2ip distance=2 comment=WAN2 add dst-address=8.8.8.8/32 gateway=gateway1ip /tool netwatch add down-script="/ip route set [find where comment=\"WAN1\"] distance=3;\r\ \n:log warning \"WAN1 down, switching ...

anav Thanks i will try it tonight. 2frogs Exactly my case... I can put the cable modem/router in bridge mode and get the correct gateway in my mikrotik, but if anyone resets it i have to do it again. I havent found a way to do it in a dsl modem/router since it gets conected to the internet by some ...

That is not to difficult IP Route destination=0.0.0.0/0 gateway=gatewayIP (of primary WAN) ping gateway distance=1 (to be clear these are gateway IPs of the ISP, not the WANIP the ISP has assigned to you. If I disconect the coax cable from my cable modem/router (wan1)... it wont change to the dsl c...

Hello,

It's my first time on a Mikrotik.

I have 4 WAN. (WAN1 - WAN2 - WAN3 - WAN4)

I need a script, when WAN1 is timeout, WAN2 takes over.
When WAN2 is timeout, WAN3 takes over, ....

Please help

Thanks you.

did you find a solution? Im looking for the same exact thing.

i have 2 wan connections. I want the Mikrotik router to switch from 1 to the other when it fails to get internet access. wan conections: ether 1 = dhcp client for a cable modem/router (ip = 192.168.0.1/24) >>>>>>>>>> main internet connection ether 2 = dhcp client for a dsl modem/router (ip = 10.0.0....

changing manual tx power to 13 to get a signal of -52-53 was the problem.... exact same configuration swithing tx power to default (-38-38 signal) give me max throughput... Now i get extactly the same speed from the ptp than if i do the speedtest by ethernet cable from modem. how do i keep the speed...

How do you test the bandwidth? What equipment? What processor in the test equipment does the down / upload? i test the bandwidth in www.speedtest.net. I test it in my pc AMD FX 6300 3.5ghz (six core cpu). with Ethernet cable from router/modem connected to PC i get 340-380 mbs. in my other house wit...

i have sxt SA5AC connected to SXTsq 5AC creating a PTP connection with a distance of 300m, getting only 20mbps when using nstreme, then i switched to 802.11. To my surprise i get 300mbps RX, 400mbps TX. not sure why i don't get the same rate both direction. I'm pretty happy with the 802.11 result. ...

switch wireless protocol to 802.11

in 802.11 i only get about 20mbs.... what could be wrong?

ptp link is like 200m. The max throughput I'm able to get is 160mb of 400mb bandwidth available. Has anyone achieved higher? link status Strength -53/-53 dBm ccq 93/88 % signal to noise 55 dB protocol nstreme this is my configuration PTP BRIDGE AP # feb/18/2018 16:33:56 by RouterOS 6.42rc28 # softwa...

It is possible to support both tcp and udp on the same port in general, but unfortunately OpenVPN cannot do it.
When your provider has specified udp, you are out of luck with a MikroTik router.

so thats is what is causing mikrotik to connect then disconnected? the protocol udp?

proto udp.
That is not going to work with MikroTik.
should be proto tcp (or actually: MikroTik should support udp)

can a port support both protocol at the same time? I think that port is tcp and udp

Having problem setting mikrotik with paid openvpn service. Whats wrong with their configuration? Mikrotik connects and disconnect. doesnt give ip or webaccesss. Firewall rule and everything is set... other protocols work fine, but they are slow. openvpn server: dev tun proto udp remote ip xxx.xxx.xx...

has anyone successfully configure mikrotik's openvpn client with Torguard OpenVPN?

You can use more wan lines and distribute the connections between them according to some rule. Look for pcc. If you want to bond the lines, you need the support for this on the second side also... i'm very new to this and cant find a guide. What i want to do is something like this https://www.youtu...

i have RB951Ui-2HnD.
Its possible to use multiwan in this model?
i have 2 internet conection 11 mb and another one 84mb
can i bound those 2 conection and get 95mb?

if this model cant do it, tell me witch can.. cheapest first.

thanks!