MikroTik

ivicask

Without RIF file, we can't fix issues that only some people have observed.

Funny, i just upgraded SXTsq to 7.17rc and same thing happend, all menus empty and winbox keeps disconnecting over ip, mac or romon, dont know how to give you any usefull log...

ivicask

Upgraded home-RB5009 from 7.17beta6 to rc1, containers, capsman, ... Winbox3.41 - lots of dialogs with empty info at first (Files, Wireless Registration, Capsman Remote Cap, DHCP Lease, ...). Only after sometimes minutes the info came through. - some containers started, some not. No reason visible ...

ivicask

Hey Mikrotik, it's already been a month since beta4, and no new releases since, are you okay? :-)

Well i hope they are fixing wireless problems, give them as much time needed..

ivicask

I had multiple hap2 acs got bricked after updates and I netinstalled some of them several times already.
I suggest you buy new models with more storage same as I did or don't update them anymore...

ivicask

Can anyone else test this also to confirm? Just tried with 7.17beta2 and super-fresh 7.17beta 4 ) with no luck. Queues on wifi1 (5GHz) and wifi2 (2.4Ghz, not used, but anyway) as per your instructions, replacing wireless-default . Exact same symptoms. Test setup used : - Realtek 8821ce / AX201 lapt...

ivicask

After having months of constant disconnects and i tested every beta versions since 7.15 to 7.17 and tried every possible setting i may discovered something. I changed wireless interfaces default queue type wireless default(SFQ) to CODEL ( /queue/interface>) add fq-codel-ecn=no fq-codel-interval=60ms...

ivicask

This is exactly my observation with same settings tried. For example yesterday i tried to watch movie and my LG OLED and Samsung soundbar disconnected with connection lost 4 times in 2 hours while i try to watch a movie... Most of the time router kicks all clients same time with query timeout (or co...

ivicask

Logs full of connection lost for various devices For example Samsung soundbar not moving inch, standing next to HAP AX3. disconnected, connection lost, signal strength -24 disconnected, connection lost, signal strength -32 etc.. Also devices sometimes roam from 5 ghz to 2ghz again under for signal f...

ivicask

Also got 2004 at work and had to use fastrack or it couldn't do more then 1000ish mbit on pppoe .

So make sure your fastrack rule is properly set.

ivicask

TL:DR; 7.16rc4 fixes all wifi related issues. I recently was trying to stream a remux to LG C2 via Plex and found out i was also running into the same problem. The Plex log was showing as device(WebOS tv) was constantly getting disconnected and reconnected which then continued the stream on tv. Aft...

ivicask

Looks Good, but gives WebFig Vibes because of missing Tabs when opening interface or in-depth menu I would prefer if there is a wide option to use tabs or just scroll and collapsable submenus, or Tabs +1 for this. Instead directly clicking on desired tab i need to do 2 clicks now. Also it seams i c...

ivicask

Honestly I need to check, but always there is a mix of SA query timeout and client disconnects.

I will check.

I had bunch of those also, disabled WPA3 and also disabled Managment protection in order to fix it.

ivicask

@infabo I agree with you here, cAP ac is great device, had them before cAP ax and WiFi was good. Then I wanted to implement WiFi6 as all of my devices, except IoT and cameras, are WiFi6 capable and with greater internet speeds that matters now. But Mikrotik's ax line gave me nothing but headaches.....

ivicask

I believe that TP-Link is also set to Croatia because you need to specify country when setting up. Also devices I have are business models, not home models so I believe that they are following the rules. I think regulatory is messed up on mikrotik, for example my home HAP AX3, i run 5220mhz on 5ghz...

ivicask

Both. Both APs are placed in the same spot and what I noticed with TP-Link is that roaming is working much more smoother and better. Going from one AP to another I don't even notice that device roamed to another AP. With cAP ax it was always disconnect, switching to 5G then reconnection to AP. Some...

ivicask

Updated hap AX3 from 7.15.3 to 7.16RC. Entire WIFI/capsman configuration empty(All the tabs, configuration, channel, security..etc), router half responsive, cant connect phone to WIFI at all, barely managed to connect via Winbox. I tried to make supout file for support but that also was somehow brok...

ivicask

That modem supports only 2CA, mobile phone supports more thats why you get better speeds on phone. I recently installed also here in Croatia HT link but with https://mikrotik.com/product/lhg_lte18#fndtn-specifications It connects to 3 freqs same time and i was getting over 300mbit with not even full...

ivicask

2024/06/15 12:29:41.394275 [fatal] writing config file: write /opt/adguardhome/conf/.AdGuardHome.yaml9142876731003399955: no space left on device

Container doesn't start after beta 2, I got 27gb free on usb...

EDIT:Update again messed up paths and keeps changing my only one usb from usb1 to usb2..

ivicask

Actually you shouldn't enable FT unless using CAPsMAN and multiple APs... Not quite. It can also be used for roaming between radios of the same AP provided same SSID is used. Exactly, i do have CAP and roaming between them works wonderful (HAP AX3(capsman) and HAP AC3(cap)), the problem i described...

ivicask

Yeah, but i dont want to do any workarounds when i just can just revert to 7.14.3 and i dont have any problems... Fact is new Qualcomm drivers in 7.15 messed up allot of stuff regarding wireless... And as i said, i dont have problem at those signal levels, problem is ONLY for devices very next to ro...

ivicask

Was hoping 7.16 to fix roaming issues, but no luck, all worked perfect until 7.15 and new drivers. My devices keep roaming from 5ghz to 2ghz and thats very next to router under full signal, and often multiple devices roam same time(Samsung s23, LG OLED TV, ASUS tablet). I already reduced 2ghz to 10...

ivicask

sometimes they are connected for hours then suddenly all roam to 2ghz
Ah OK, then maybe it depends on the DFS.
What 5GHz channel are you using?

Not using dfs, no radar detects,5220.

ivicask

Was hoping 7.16 to fix roaming issues, but no luck, all worked perfect until 7.15 and new drivers. My devices keep roaming from 5ghz to 2ghz and thats very next to router under full signal, and often multiple devices roam same time(Samsung s23, LG OLED TV, ASUS tablet). I already reduced 2ghz to 10...

ivicask

Was hoping 7.16 to fix roaming issues, but no luck, all worked perfect until 7.15 and new drivers. My devices keep roaming from 5ghz to 2ghz and thats very next to router under full signal, and often multiple devices roam same time(Samsung s23, LG OLED TV, ASUS tablet). I already reduced 2ghz to 10 ...

ivicask

My adguard container won't start after update , nothing in log, anyone else has problem with containers ? No problems here on a CCR2116. Six containers (pihole, open-speedtest, samba, uptime-kuma, home-assistant, esphome). I see now whats wrong, update decided to change my usb from USB2 to USB1 so ...

ivicask

My adguard container won't start after update , nothing in log, anyone else has problem with containers ?

ivicask

ACHTUNG !!! ALERT !
Do not use this version with CRS354 !!!

Huge packetloss, huge performance drop, unusable on some ports.

Same, switch stops forwarding traffic properly after few hours, had to revert ..

ivicask

AX HW or older ARM AC with wave2 drivers?

Hap ax3

ivicask

I also have positive signal strenghts issue and roaming is messed up, multiple devices randomly roam from 5ghz to 2ghz 1-2m from ap under full signal(below -40 db ) and then hang on 2ghz, which makes no sense and never had such issues on prev versions.

ivicask

I have same issue on multiple locations every 1-2 days handshake stops, disabling/enabling interface doesn't help, only thing that helps me changing to any random port(client side) and immediately starts working, i can even return very same port which was before and still it will work fine. So i hav...

ivicask

@MikrotikUser100 Besides the log message on your mikrotik device (SAQuery timeout...): how do you experience the problem on your client device? It's unusable, as we use it remotly. It's not just a log message, it's a total disconnection from the network and hence complete instability and inability ...

ivicask

Still getting random query timeout disconnects on HAP AX3 on 7.15 RC2, no problems on 7.14, all started happening since new Qualcomm drivers got implemented. Also roaming is super bad, clients hang on 2ghz practically near router full signal and never or rarely roam to 5ghz. I hope this doesnt go in...

ivicask

Since the new driver was added some client devices are getting SA Query timeouts and have issues with connecting to wifi then. SUP-151059 created. I suppose it will be similar issue that was fixed for previous driver version already.

Also getting alot of query timeouts, vs zero problems on 7.14.

ivicask

Updated our switch CRS354 to 7.15rc and in morning half of clients couldnt get internet access,or couldnt get DHCP, nothing in logs, discovery didint work, had to revert to stable

ivicask

Currently none of the AX-devices support 160MHz wide channels.

This one supports 160mhz
https://mikrotik.com/product/mantbox_ax_15s

ivicask

any update or workaround with having pppoe-client as WAN source receiving 1gb+ bandwidth?

I would like to know the same, CCR2004 can't push more then 1gb without fastrack with pppoe client.

ivicask

Playing with my shiny new RB5009 - it will indeed pass the full 2G (actually, 2.2G) I'm getting from the cable provider. That with fasttrack enabled. However, the instant I enable a queue of any kind the speedtest drops to 1.2G maximum. While I probably don't need any QoS - I was hoping to optimize...

ivicask

Rebooted router,even tried update to latest beta 7.15, it still runs on its own on times i didint specify: Your screenshots now only show it only running once now though, at 10:00. Are there other log entries that show it running at 8:00? Is the time set correctly? Please post your full config. Yes...

ivicask

I have completely removed all scripts and re-named them and re-added. Rebooted router,even tried update to latest beta 7.15, it still runs on its own on times i didint specify: Last run Mar/20/2024 10:00:00, what the hell started it ???? Scheduler clearly shows next run Mar/21/2024 06:00:00, and it ...

ivicask

Dont have DHCP clients or any dhcp scripts. Already did full export and searched for this line, its nowhere else. BTW have same issue on 5 different routers(diff models and diff RouterOS) I have this scheduler+script for many years, i only copy pasted new updated script code into my (BADiplist) scri...

ivicask

The last few lines starting with "$update" call the update function, once for each URL defined. Thus, the script runs once for each "$update" call that is not commented out. No commands to mess with the scheduler. Note that the script adds the entries on the blacklist with a 3-d...

ivicask

I found this script on the forum. It works OK on my hEX S running 7.13.2. The only change I've made was to concentrate all entries on a single "blacklist" and select the entries via the comment field. MH :global readfile do={ :local url $1 :local thefile "" :local filesize ([/to...

ivicask

https://www.qualcomm.com/products/internet-of-things/networking/wi-fi-networks/networking-pro-series/qualcomm-networking-pro-620-platform Something like this for HAP AX4 i hope. Name: quad-core Arm® Cortex®-A73 Processor Clock Speed: Up to 2.2 GHz Spectral Bands: 6 GHz, 5 GHz, 2.4 GHz Peak PHY Rate:...

ivicask

Getting POE FW upgrade fail on 7.15, had same even on 7.14 stable.

ivicask

Also that AP has only 7° antenna beam width, not the best candidate for multiple clients, this AP is build for P2P links.

ivicask

Same here, dual fans screaming on 8500 RPM! after i plugged copper SFP,its driving me nuts Not that I would swear about accuracy of temperature measurement, but in my perverted mind running at 65° something intended to work in the range 0-70° is already a bit risky, you are having 71° with the fans...

ivicask

Same here, dual fans screaming on 8500 RPM! after i plugged copper SFP,its driving me nuts

ivicask

!) rose-storage - moved SMB service to the RouterOS bundle; !) smb - removed legacy SMB service (replaced with newer and faster ROSE SMB service, compatible with SMB 2.1, SMB 3.0 and SMB 3.1.1); It still doesn't work for me... Windows clients see the share but cannot access it. https://i.postimg.cc...

ivicask

Im pushing 500mbit TCP on AX3 and CPU load is on 50%.

ivicask

Regarding this *) leds - added "dark-mode" functionality for hAP ax3 and Chateau ax series devices; How do I enjoy this for hAP-ax3? I tried with ip leds settings but there is not a "dark mode" anywhere (set all leds off option was already there before this release, but the only...

ivicask

+1 for allowing us changing wireless rates in new drivers and new ax devices.

ivicask

I have completely metal USB 3.0 drive and it still killed 2ghz on my HAP AX3, even if i used 2m USB 3.0 extension cable and moved usb stick drive away from router and even wrapped it completely in aluminium foil, nothing helped. Solution was to plug it on short USB 2.0 extender cable which killed US...

ivicask

@masterpotato what kind of traffic are you trying to queue?local or internet? For routed internet or any other routed traffic queue must work if you set it right(and not using fastrack), if you are trying to queue local network traffic then you need to turn on bridge filtering which will have big im...

ivicask

Exactly. Because of those big ears AX3 has better reception sensitivity and allows for a more stable connection given same distance, same client, same infrastructure in between. I didn't need any power measurements to see it happening. I did the tests with both devices on the EXACT same place in my...

ivicask

From my findings you get absolutely no benefit on hap ax3 over ax2 due regulations(hap ax3 drops power down compared to ax2 to match the gain from antennas) in most of the world ,except if you live in America or ignore regulatory, 100% same signal/coverage, speeds. My user experience using both AX2...

ivicask

From my findings you get absolutely no benefit on hap ax3 over ax2 due regulations(hap ax3 drops power down compared to ax2 to match the gain from antennas) in most of the world ,except if you live in America or ignore regulatory, 100% same signal/coverage, speeds.

ivicask

:local radios [/interface wifi radio find] :foreach cap in=$radios do={ :delay 10 /interface wifi radio provision $cap } I use this as startup script with delay as quick dirty fix for automatic channel selection until mikrotik doesn't add channel reselect or better solution for auto channel selecti...

ivicask

How much free ram you got ?If you have large lists in adguard it can use alot memory and cause crashes if you haven't limited max container memory.

ivicask

What's new in 7.14beta4 (2023-Dec-29 10:05): *) leds - do not show LTE connection state/mode using RGB power LED from configless LTE modems; Thank you, now its back to normal. *) system - improved memory allocation for ARM64 devices; ~100MB more free RAM on hAP ax^3 200mb more free for me also on A...

ivicask

I just notice that i have same problem with one client after updating everything to new qualcomm drivers and new capsman, note that all other devices connect fine on all CAPs

Not sure even which device it is, client didint complain back yet, might be some smart crap device.

ivicask

When i remove it , it show anoying error

Couldnt' remove wireguard peer <key...> - cant remove dynamic object(6)

Is that back to home enabled ?That's why probably you can't remove it.

ivicask

Hi, I have updated my hAP ac2 and switched to wifi-qcom-ac drivers. Seems there is problem with my old ipad mini 2 running software version 12.5.7. Ipad is unable to connect to wifi network, it is reporting invalid password. But password is correct. Androids works ok, windows 10 ok, even old rpi co...

ivicask

As mentioned by others bonding stopped working for me on multiple devices after 7.13 update, and one wireless cube with out of box config disappeared need to go check what happend to it after 7.13... Edit:So 2x CubeG updated same time and same way(automatic check for updates), one update fine, other...

ivicask

I still have memory leaks even on 7.13RC2(over 500mb a day)
SUP-136530

ivicask

Other day 7.12 bricked HAP AC2 after 2nd reboot and routerboard upgrade. Now i updated 4011 to 7.12.1, first boot was ok, did reboot for routerboard and its not comming back online...Whats going on with routerboard updates?

ivicask

Ullinator, that is not true. Nothing has to be changed on the CAP even in new capsman. Make a new topic, if you are not sure how to use it. There should be no reason to manually configure CAP clients. What about routerboard upgrades, i always need to log into cap and turn automatic routerboard upgr...

ivicask

Does new wireless drivers suport QCA9556?(wap ac)?

ivicask

Code: Select all
system - fixed process multithreading (introduced in v7.9);
care to elaborate please?

I would also like to know this.

ivicask

I had exactly same issue at customer with same rotuer and qnap nas, actual ports would go down while you copy files(other ones that don't copy traffic) ,sent mikrotik support logs and they told me I'm not suposed to use it as switch, like Wtf mikrotik ? And issue persisted from v6 to most recent v7 ...

ivicask

I can confirm the 1350 MTU, had weird issues where internet speeds where good for me but SMB traffic was super slow, droping mtu to 1350 fixed it.

ivicask

running on issue where i can't force Pihole DNS. I was using OpenDNS and it was working perfectly fine with same NAT rules DST-NAT add action=redirect chain=dstnat dst-address-type=!local dst-port=53 protocol=tcp src-address=!pi-hole_ip-add \ to-addresses=pi-hole_ip-add add action=redirect chain=ds...

ivicask

The reason is regulatory, most of the EU users are f..ed and this rotuer will perform almost at half compared to Americans buyers for example. If I select my country, 2.4ghz runs at 16 tx power and I can barely use my net downstairs ,if I select no country (defaults to USA and 26 tx power) I can hav...

ivicask

You simply need two devices.

Or make us happy with something like HAP AX 3 but with all 2.5gbe ports and 160mhz support for wireless so I can actualy have full use of 2gbit internet my Isp gives me .

ivicask

Hi, Issues with CAPSMAN on a RB4011 router, error type "removing stale connection". Back to version v7.10 and OK. BR. I got RB4011 and capsman works fine on 7.11, usually that error is firewall problem, try allowing UDP "5246,5247" on input chain on your bidge side and see if fi...

ivicask

Hi,

I have Samsung flash disk usb3 and WiFi is working fine...

Metal vs Plastic drives.

Use metal sticks if you want no problems.

ivicask

Also There is no "Make static" item in the DHCP Leases menu.
Yes there is.
Used it several times yesterday.

It used to be there on right click menu of lease and it was gone at some point recently, you need to open lease to see Make Static button.

ivicask

I added the following to 'enable' steering On the CAPsMAN /interface wifiwave2 steering add name=<NameOfSteeringGroup> neighbor-group=dynamic-<wifiSSID>-<RandomHex> rrm=yes wnm=yes Note: You do not get autocomplete for the neighbor-group-dynamic= parameter, you need to obtain the name of the group ...

ivicask

@sirbryan i run 20mhz and 80mhz for 5ghz ,devices are Samsung s23 ultra , Tab S8, Asus laptops with ax20x etc..

ivicask

To lower the distance at which a link can be established? You can do that by manually lowering maximum transmit power. Well what about when im on lower signal on 5ghz, if i could disable lower rates, like set min 24 or 36 as i had on wave1 so my devices dont get stuck on lower 5ghz signal and move ...

ivicask

I know all this but it doesnt work regardless of this setting .For now my script in scheduler works to help band steer to 5ghz until mikrotik does some fixes /improvments to wave2. 7.11beta2 enabled 802.11v BSS transition management requests and 802.11k neighbor report responses. What more would yo...

ivicask

I know all this but it doesnt work regardless of this setting .For now my script in scheduler works to help band steer to 5ghz until mikrotik does some fixes /improvments to wave2.

ivicask

Yeah i did that already... EDIT: I added this script to scheduler to run every 10 sec :local MacAddress "xx:xx:xx:xx:xx:xx" :local ClientSignal -51 :local InterfaceName 2GHz /interface wifiwave2 registration-table remove [find where mac-address=$MacAddress and signal > $ClientSignal and in...

ivicask

Is access list broken ? /interface wifiwave2 access-list add action=reject disabled=no interface=2GHz signal-range=-120..-51 I wana kick clients at home with very strong signal from 2ghz to force them to roam to 5ghz, its not working for me. If you want to kick clients with strong signal, you shoul...

ivicask

Thankyou Team.
*) wifiwave2 - fixed registration table statistics (introduced in v7.11beta4);

Maybe this was reason access list was also broken? Will try when im home.

ivicask

Thats why i wrote "at home" I have all 5ghz capable devices dont worry :)

Also @mikrotik when we will be able to change minimum rates on Wave2? I want to disable lower rates which helps with roaming great deal and also improves performance overall.

ivicask

Is access list broken ?

/interface wifiwave2 access-list
add action=reject disabled=no interface=2GHz  signal-range=-120..-51

I wana kick clients at home with very strong signal from 2ghz to force them to roam to 5ghz, its not working for me.

ivicask

@mantouboji for a client the IP address does not to be renewed until TTL expires. So what is the TTL of your DNS registration? WG will renew the resolve on restart of the WG peer. You can't check every so many seconds if the DNS changes brcause of Round Robin when having multiple IP addresses. Then...

ivicask

) wireguard - fixed peer connection using DNS name on IP change
I removed all scripts and this finally fixes WG and it works properly with dynamic hosts on ip change

ivicask

Well then all other vendors are breaking regulatory (ASUS,DLINK,HUAWEI,ARUBA,entire ISP routers in my country )etc, or there is something broken with regulatory on mikrotik If you take cheapest asus ax router it costs exactly HALF price then cap ax and i get almost double range or speed then any mik...

ivicask

persistent keepalive doesnt help with that...and yeah i have it both ends, moments IP changes on server peers never reconnect until i disable/enable peer.

ivicask

Well whats funny, the best performance i got out of any of mikrotik new AX devices was to NOT select any country, moment i select my country it drops TX power from 26 to 18db and range and performance drops so drastically(almost 50%) that i wonder whats even the point of having this new router...

ivicask

For anyone wondering, wireguard - retry "endpoint-address" DNS query on failed resolve;
Does nothing to help with dynamic peers, i had to re-enable script to fix peer after IP changes because tunnel died.

ivicask

That's because the version you have loaded, is a bundled version (containing all packages). Those can effectively not be uninstalled. It's a test version, with normal released versions you should not have had this problem. Test version on a device with accessibility problems, not a smart thing to d...

ivicask

What are they doing here?They are there OUT OF BOX on every router like that, i didint install them.

And no, i cant uninstall any of them.

I also tried installing only individual packages like
system-6.49.8-arm.npk
wireless-6.49.8-arm.npk

Also not enough space error after reboot..

ivicask

Which part of there is NOTHING on them except bridge is not clear for you?Nothing was ever installed! Latest version which i managed to install on them was 6.49 beta 22, i cant install nothing newer, disabling extra packages etc makes no difference(You cant uninstall them)..

ivicask

I have still LHG devices which cant be updated even to latest 6.49.8, they literary only have bridged wlan and lan and thats entire config and disk is empty. So im not allowed to have latest security on my device aginast CVEs and similar. Im supposed to climb on towers and do netinstalls? There is s...

ivicask

Its so stupid that we need to netinstall basically new purchased devices or even worse getting bricks after simple software update, mikrotik really should address this somehow or test better updates on their lower end routers.(And thats still alot of them with 16mb flash) Like for example why does m...

ivicask

Indeed I also update a hAP ac2 without problems, but on that device the flash memory space is getting very tight. When you have put files of your own on the device, remove them. When you have installed extra stuff like user-manager, remove it (move to some other device). When you have done upgrade ...

ivicask

Just try, if only 8 rules you can copy them to raw in less then 5mins.
Also what you can do to gain a bit perfomance depending on your rules is to move ones who get more hits first in order if posible.

ivicask

I cant upgrade my hap ac2 from 7.10 beta 5 to beta 8, after reboot i get
router was rebooted without proper shutdown, probably kernel failure..

ivicask

@EdPa can you give more details about "wireguard - retry "endpoint-address" DNS query on failed resolve;"
How many times will it retry? Does this solve our problems with dynamic ips on peers where we need to re-toggle tunnel to fix it after IP change?

ivicask

At this point it doesn't matter why it worked for you on older versions, as you where told multiple times, you need to allow UDP port on WAN interface or wireguard wont work no matter what, thats the same response you will get from Mikrotik support.

ivicask

Unfortunately, I've just had to reboot my hAP ax^2 again because none of my clients could associate anymore ("key handshake timeout"). Seems this issue hasn't been fully resolved yet in 7.10beta5. WPA2 only, so WPA3 compatibility issues are excluded. Exactly the same issue here both on st...

ivicask

Seeing alot of Handshake timeouts and pkmsa errors also...

ivicask

Seams PMKSA errors are caused by WPA3, i disabled it and left only WPA2 and all errors are gone. Wireless was working like total crap, clients constantly couldn't connect to mostly 5ghz but sometimes also 2ghz interface and took multiple attempts sometimes to get wifi connectivity. Logs IS full of t...

ivicask

Internal Iperf goes between 800-850Mb using Wifi6 and WPA3 (multiple runs done). Nothing special done on settings of AX3 bar setting correct country, choosing a clear channel and setting SSID and security. While sitting on top of router ? ...see how quickly that speed changes as you move away. I ju...

ivicask

You cant change wireless interface queue type while its managed by capsman.

ivicask

For last 4 months I am battling whit WiFi stability issues in our school...cap acs, hap ac2s, wap acs + other cool switching stuff. A few interesting points: 1. I suggest running without adaptive-noise-immunity=ap-and-client-mode since this will trigger radio microcontroller firmware paths presumab...

ivicask

Not sure why they don't hide the option, the chip doesn't support 160mhz at all as far I know.

ivicask

Here is more every day school experience: Reboot AP, now selects chan just fine and there is no problems with any regulatory. mismatch and error is gone. Also i forgot to mention using any DFS chans is 100% unusable, false radar detects all day, i get 10+ wifi blackouts daily, sometimes APS gets stu...

ivicask

My HAP AC2 after update has only 1% now free (it was 2% on 7.8 beta 3)

I cant even do basic functionality like create system backup with 1% free.

What im supposed to do with router now @Mikrotik?

EDIT:Dyndns update scripts works again atleast which was broken on beta 3 not working from scheduler.

ivicask

UpRunTech Do you set forwarding to local? I was forced into an install yesterday that was really small HAP AC2 + 2 cAP AC. RouterOS 7.7 No switch... The caps were connected directly to the hAP AC2 with POE Injectors. Absolutely instant feed back of the roaming and signal levels of the test phone. A...

ivicask

Open separate topic, or go to one of the thousand topic about dyndns & similar that already exist Why if its 100% related to beta 3 update, it needs to be adressed and known why it happens, this script worked untouched for 5 + years for me on 100+ routers, its first time stoped working on v7.8 ...

ivicask

I noticed same issue here. My dyndns script doesn't update anymore from on scheduler (although the "Last Time Started" counter for the script does suggest the script runs). If I execute the script manually it works. Same here, I changed to /tool fetch url="..." as-value output=u...

ivicask

And another issue I just noticed on beta 3 my Dyndns script cant finish updating IP, it doesn't come to part where it writes to disk, but If I manually run script instead scheduler it finishes.

ivicask

After beta 3 my HAP AC2 has only 2% disk free(zero files on disk) i cant even make config backup now.

ivicask

Yea Capsman with local forwarding.

ivicask

I have setup with 30 caps and tops 300 clients and its pure mikrotik setup also getting same issues as in random radios crashes, need to reboot ap to come to senses, random speed drops..
Mikrotik just simple cant handle such dense setups and mix of clients..

ivicask

Radar detection on Mikrotik is simple broken, i cannot use it on any location, it detects it self as radar basically...Put any other vendor on same location it never detects radar(there arent any in fact).

ivicask

I also just realized dns cache is somehow broken on rc3 I can't connect to many servers with dyndns names, resolved IP adress keeps. changing or they are duplicated entries for same host in cache, I reverted to 7.6 for now all fine..

ivicask

Can you try disable MIMO powersave(set it to NO SMPS) under wifi card extra settings inside device manager and see if it makes speed difference.

ivicask

:local AltDNS 9.9.9.9,1.1.1.1,8.8.8.8 :local CrSrv [/ip dns get servers] :if ($CrSrv != $AltDNS) do={ /ip dns set allow-remote-requests=yes cache-max-ttl=3d cache-size=500KiB \ max-concurrent-queries=300 max-concurrent-tcp-sessions=50 servers=\ $AltDNS use-doh-server="" \ verify-doh-cert=...

ivicask

No, WifiWave2 CAPsMAN is only compatible with WifiWave2 interfaces.

What are plans for later?If we want to manage mix of new/old devices? Are we able to run 2 capsman instances, or we gona have to have 2 different Mikrotik devices in order to do it?

ivicask

Hello, I am configurating the WifiWave2 package on a hAPax2 router running on WinBox v7.6 (arm64). Both of the interfaces (wifi1 and wifi2) say that there are no supported channels. What is the reason for that and how can I fix this? I have added my configuration script as an attachment as well as ...

ivicask

What I wonder how will new wifi 6 devices work in larger setups with lots of aps/clients and also noise, because curently its misserable expirience and mikrotik performs worse then often 2x cheaper devices...

ivicask

Doesnt help i set that long time ago...

ivicask

Exactly same observation my side to the last word!

ivicask

What Channel width did it select 40 or 80mhz?Looks like 40, try setting it to 80mhz instead 20/40/80 to see if thats the issue. Also as mentioned above "skip-dfs-channels=10min-cac" that is also maybe the reason it selected 40mhz on more crowded channel instead using higher one which then ...

ivicask

I have entire collection of various DoH related errors, im using NextDNS DOH and i dont have issues using their DNS client for windows or using it for example directly in my samsung phone, but on mikrotik every day i have 1-3 mins dns blackouts or random delays followed with attached errors. Is this...

ivicask

I was importing certs on RC3 for NextDNS (/tool fetch url=https://curl.se/ca/cacert.pem) and i noticed this error, is this related to cert changes?

ivicask

Yeah its a problem that mikrotik needs to fix, simplest WG setup and peer doesnt work on like 50% reboots(STATIC IP NO DNS), i have to add netwatch script in order to retoggle it and fix it after boot.. And on some locations peers just die permanently and i need to create new WG interface(client sid...

ivicask

And any of you two sniffed the traffic to see what's pushing the phone(s) to disconnect? Sure have. Did extensive trouble shooting with Mikrotik too. They finally copped to the fact that they can't deal with interference. They called my environment "unique." Except I had the exact same pr...

ivicask

I also dont have this issue with other WIFI vendor on same network, had 2 weeks aruba APS zero issue, with mikrotik almost every day, sometimes 2-3 times a day..

ivicask

It looks like it has trouble getting a DHCP lease. That is enough reason for "modern" devices to disconnect the L2 connection as well. Debug it from the DHCP side first. Well whats user @dbrowning2 above saying about forcing 1,6,12 options on DHCP ?I dont understnad hes post fully. I dont...

ivicask

Getting this issue almost on daily on all locations and various clients, its driving me nuts, im watching on my Samsung phone and pressing connect and it keeps disconnecting then settles after 2-3 mins and then stays connected..

ivicask

Hello Everyone, My customer is using global DNS i.e 8.8.8.8, 1.1.1.1 and we have our own DNS with our end, Here the issue is comes to Akamai traffic because they will serve CDN traffic using ISP DNS based only. Which NAT rule or any other option will help for this solution. Customer is using static...

ivicask

https://forum.mikrotik.com/viewtopic.php?t=156124 This is old issue, as matter of fact it just happend to me while moving between 2 caps, samsung s21 ultra phone, shows connected full signal, can't acces network, can't connect to router, wifi off/on, all works fine.. Only solution I know it works is...

ivicask

Personally, I find the design of the device disappointing on the following points Major No SD card or USB store POE In/Out in one port? - no 802.3af/at - no daisy chain Why not a design like hEX, hEX S, hAP ac, hAP ac³ Minor Ports are gigabit only To everyone complaining about no USB, you do realis...

ivicask

Wave2 devices compatible with capsman, dark mode for Winbox, I'm modest.

ivicask

It's same issue regardless of rotueros or architecture can confirm.

ivicask

This isn't on the website yet, but master distributor Allnet lists it . They even have a datasheet . It's basically the same as the CRS504, but with more ports on a Marvell 98DX8525. Also, USB-A. Isnt exactly a leak when Mikrotik them self announced it in their YouTube channel :p https://www.youtub...

ivicask

I think than lost radio time to listen for nv2 or nstreme on home AP is completely useless and nonsense....

I wonder about this also now that you mentioned it, I also set 802.11 just to be sure, but did some tests there is no difference between any or 802.11, not sure how any works exactly.

ivicask

I can spare you all the trouble, getting longer range aps won't get you much benefit, you will have about same speeds at those distance, they only perform better at bigger distances..

ivicask

You are testing both ways and over TCP, for that device and 2km its very good result... Try testing one way only, and also try test UDP traffic, its not only TCP that will go thru that link... I got very same APs and at same distance, i get 450mbit UDP in one direction(around 170mbit both ways same ...

ivicask

Wondering why is this still not fixed? Any reason we should not be able to change cpu freq on 4011 & v7 same as we could on v6?

ivicask

What is CPU load during bandwidth test? That is only single core cpu, it cant generate much traffic, use PC to do tests.

ivicask

Doesn't that make you wonder? I just tried very same config file from my phone on Windows 11 laptop wireguard app and im getting full speed (around 70mbit which is max of my line), even running hotspot from my phone to laptop again full speed over phones net. I also tried 3 different Samsung phones...

ivicask

I actualy noticed the same thing from my phone can't get more then 20mbit with 4011 on other side and s21 ultra as client, also same version routerOS, gona try older versions tomorow I tried about everything else today from changing MTU, completly disabling any firewall rules or queues, nothing made...

ivicask

I just did netinstall yesterday on win11 I had to disable firewall completly and also disable any other adapter like wifi even they where not connected, then it worked fine.

ivicask

BTW i have no issue with torrents, its 100% respecting limits for me. It could be something to do with the torrent client (local or remote), or the number of seeds? In my case with qBittorrent and a torrent with thousands of seeders, I did experience the issue with torrents too. But that was with a...

ivicask

I started the other thread (linked in post 2 ). Unfortunate that there are duplicate threads now but on the bright side it's a good testament that the bug is becoming more noticed and prevalent and should be taken more seriously by support. Besides for game downloaders as mentioned by @ivicask, ano...

ivicask

I'd like to see a bandwidth measurement from the device doing the downloading too, to see if the queue works, without relying on measurements on the router.

If I run speedtest or simple driver download from nvidia it's respecting set limit exactly as set in queue as we mentioned already.

ivicask

Do you see the same behavior when using CAKE's shaper? That should be preferred if you're matching a slow ISP link. Make the simple queue unlimited and enter your bandwidth in the CAKE queue types to give it a try. 70mbit isn't exactly slow link, and queue doesnt matter, it completly chokes dsl lin...

ivicask

I did very dirty and very complicated workaround by making queue which matches such downloaders with multi connections and then I set speed almost half from desired one. That's true I noticed it does the same thing with the Epic Games client. What's the general route you've taken ? You're marking p...

ivicask

https://forum.mikrotik.com/viewtopic.php?p=931315#p931315 I would also like some answers on this but even Mikrotik support I contacted few times about this never gave any useful info.. wow ok I thought I was crazy. Thing is, I am glad we finally narrowed down something that is happening (IMHO) for ...

ivicask

viewtopic.php?p=931315#p931315

I would also like some answers on this but even Mikrotik support I contacted few times about this never gave any useful info..

ivicask

I just noticed weird bug on beta 40 with wireguard and interface list. I have last firewall input drop rule with !ALL_LAN. Wireguard interface is added into ALL_LAN list, but still rule drops wireguard traffic until i quickly enabled/disable this rule, then it works until next client reconnection. V...

ivicask

Just noticed bug which costed me 2 hours of debuging... For some reason when importing my mangle rules which contain routing marks it duplicated them and i had multiple tables with SAME NAME.So mangle marks looked ok and my table name was right, but it was "wrong right one".... Why would y...

ivicask

CAKE type was always meant only for interface queue, it had no effect when used in simple queue. How are we now supposed to set different download/upload speeds for asymmetrical links? Can you add this to Cake queue it self? Now with this change we can't control it via simple/tree queue and by sett...

ivicask

@emils Can you explain this?

queue - do not allow using CAKE type in simple and tree setups (already configured queues will be disabled)

So where can we use Cake? Only as interface queue? Was it disabled due router instability and crashing problems ?

ivicask

Change queue type to ethernet-default

Tried every possible queue type, bucket sizes, routeros versions past few years, empty routers with zero config just ONE simple queue and it still makes no difference for this kinda of scenarios.

ivicask

Exactly same issue here for some time, sent numerous tickets and talked to many people never found answer or proper solution. This happens the most with downloaders like Epic games or Steam or even worse case with Adobe Products downloader which opens a lot of simultaneous https connections to serve...

ivicask

That "recursive routing", Mikrotik has an example. But you'd just use the "host ip" you'd want check, instead of the 8.8.8.8 ones in the example. See https://help.mikrotik.com/docs/pages/viewpage.action?pageId=26476608 Since those are DNS addresses it make it look like DNS is in...

ivicask

Try updating firmware of that intel card and try both ports if its dual port card https://www.intel.com/content/www/us/en/download/18190/non-volatile-memory-nvm-update-utility-for-intel-ethernet-network-adapter-700-series.html I had similar issue with x710 10gbe model after updating everything is wo...

ivicask

Upgraded 1009-7G-1C from v6 stable to v7, half hour passed not coming back online, I hope I'm not victim of upgrade like here..
viewtopic.php?t=181525

Need to go to location tomorow anyway but comon mikrotik how you not solve this issues by now?

ivicask

Cpu speed setting still missing on 4011, can't even view cpu current speed nowhere in resources.

ivicask

No reason not to work perfectly fine, it's clear line of sight, even 5ghz would work just fine I'm sure, but if you want to avoid posible interference go for 60ghz.

ivicask

I run about 500 MAX hotspot users at times on cheap HEX S, internet speed is 100mbit, few queues and firewall rules, and router doesnt even break a sweat.

So it more depends on bandwidth you mean to push instead of just number of users it self.

ivicask

What's new in 7.1.5 (2022-Mar-22 13:03):

*) route - fixed "table" menu emptying after RouterOS upgrade;

Thank you :)

ivicask

@strods
viewtopic.php?t=183548#p917086
"pe1chl, msatter, CTassisF, osc86, IntLDaniel, ivicask - Very sorry for missing routing configuration after an upgrade. We are working on a fix for this."
You broke your promise :p

ivicask

I had this issue with hAP AC with Hex S on the edge as Capsman after upgrading both to 7.x.x. Nothing fixed the CPU usage and disconnection issues even upgrading to the latest 7.1.3. I'll have to resign to the fact that ROS 7 might be best for newer multi-core CPU/ARM devices only. I'm still gettin...

ivicask

Nowhere they say you will achieve actual "600 Mbps with 40 Kms range" it just says you will be able to establish connection up to 40km, i dont think such product even exist in this world,also dont mix connection rates and actual speed achievable. From config all i can tell you this to try:...

ivicask

I took the JUMP and hit the concrete on the bottom with my head!! WTF Mikrotik!! Erase the routing tables (/routing/table), leaving me with setting about 50 different routing-marks all who are all over the place!!!!! I started the recovery but ran out off breath doing them all and will think hard o...

ivicask

Dear Sir or Madam, I am reaching you to check the contradiction recently we have faced with your product where the label and part number on the device says LHG XL but the routerboard shows different model, Is this product refurbished? or new policy in Mikrotik company where we might not be aware of...

ivicask

IM getting this on practically any mikrotik AC device, HAP,CAP,WAP, and with multiple clients like phones or laptops etc..

This example from capsman in local forward and WAP AC, S21 Ultra, 3m away, mostly clear environment, less than 10 clients doing no traffic same time as me during test.

ivicask

DFS and radar detects are biggest problem for me currently on mikrotik wifi setups and specially on more dense capsman setups, i get so many radar downtimes per day not to mention often CAPs just get stuck forever in detecting-radar state until i reboot them or toggle wifi interface on/off, so im fo...

ivicask

Do you have "Use IP firewall" for bridge ticked ON?Thats what broke it for me on v7, same setup works on v6

ivicask

I'm getting 400mbit download and 500mbit upload 3m from wap ac or cap ac via capsman in local forward, connected to samsung s21 for example.(using local test server) 80mhz, n/ac, nothing special confing... Capsman is on v7.2RC3 and caps on v6 long therm. Very interesting seeing that the advertised ...

ivicask

I'm getting 400mbit download and 500mbit upload 3m from wap ac or cap ac via capsman in local forward, connected to samsung s21 for example.(using local test server)
80mhz, n/ac, nothing special confing...

Capsman is on v7.2RC3 and caps on v6 long therm.

ivicask

I assume he means enabling remote access .. /ip dns set allow-remote-requests=yes However when I do that, my system does not show an open port when probed from the Internet, confirming what has already been stated that the firewall does not permit DNS by default. My rules on that router are default...

ivicask

What means "if you enable it in IP/DNS". There is nothing to enable? The default firewall rule do not allow port 53.

IP>DNS>Allow remote requests, do open port check and it will show 53 as open, DEFAULT mikrotik firewall config latest OS version.

ivicask

Hes right, by default mikrotik FW rules when you check via port scanner DNS shows open(If you enable it in IP>DNS),i also manually close it to be sure...

ivicask

It's supposed to use TTL. What RouterOS version do you have? I noticed the same(any versions ever), what TTL you talk about ?In this case timeout value is empty because i never want entry to expire and get removed from address list, there is no TTL setting. I get over 1 Million DNS requests per day...

ivicask

Torch for IPv6 still not working. Can anyone confirm? @ Mafioso Please read through this and tell us where Torch is noted THEN copy and paste it into excel or any document and do FIND/SEARCH for the word Torch, just in case you missed it doing in manually. What's new in 7.2rc2 (2022-Jan-28 11:00): ...

ivicask

I dont understand, how it's possible to manufacture so called router os and still have this HUGE, 14 years nover solved problem? How to fix it??? I have Shelly device, it connects to wifi and after few seconds receives "disconnected, unicast key exchange timeout, signal strength -52". WHy...

ivicask

I have 7.1.1 on RB4011 with CAPS-man - here is some bug with bridge/capsman - any change with bridge (disable port, or change mode to rstp/none) cause almost frozen routerboard, reboot required. Simple: create bridge with eth ports, create caps-man with datapath add to bridge, then add cap. without...

ivicask

I have also alot of packet lost on ethernet interfaces and some on SFP when going from 10gb to 1gb, the fifo suggestion made it even worse, some ports have 100 000 drops in few days with it...
CRS354-48G-4S+2Q+RM

ivicask

While I think the minimum amount of flash should be higher 64M or 128M and Ram should start at 128M, this would increase the cost of the devices. In your case you reference the hap light which is basically the cheapest device mt sells (along with the hap mini) at $20 usd. It only has 16M of flash -...

ivicask

RB5009 arrived. Here's some brief testing of cake. ISP: Aussie Broadband Technology: Fibre To The Premise (FTTP) Down/Up: 1000M/50M /queue type add cake-diffserv=besteffort cake-nat=yes kind=cake name=cake-default add cake-ack-filter=filter cake-bandwidth=45.0Mbps cake-diffserv=besteffort cake-nat=...

ivicask

These addresses can be temporarily disabled I don't like the fact that I have to disable those for the memory leak to not occur, but I disabled the scheduler tasks, cleared out the dynamic addresses, and upgraded back to 7.2.rc1. After reboot CPU and memory were stable. So yes, my issue was also li...

ivicask

Dude, so far it looks like a bug in 7.1.1 and 7.2rc1, these topics are for problems related to these specific versions, please don't spam the forums with offtopic talk. Wasted 3 posts for nothing. For general "don't use v7, v7 bad" please open another topic. Thank you. So, on topic, did y...

ivicask

Updated from 7.1 hap ac2 crashing after 30mins out of memory, also cpu sticks at 35% with no traffic. Also memory leak on 2 other APs runing nothing but wifi..
Downgraded to 7.1.1 works fine so far.

ivicask

Did you add this for improved roaming?(fine tune the value to your liking) ... add action=reject allow-signal-out-of-range=6s client-to-client-forwarding=yes disabled=no interface=any signal-range=-120..-83 ssid-regexp="" At best it's not any better, at worse in your dark spots clients ge...

ivicask

Klembord-2.jpg . . To my experience this will not let you return to this AP for 6 sec, after you have been kicked out, even if your signal is now OK. Even if you set this to 1 sec, there is another cache for a short delay that says "banned(last failure ...)" This is a problem if the AP's ...

ivicask

Interesting article and I would be happy to see these improvements. One other thing that is different that I have already suggested in the past but didn't see any action except the very first days of discussion is the fact that ubnt controller is pushing the parameters to the APs and if we loose fo...

ivicask

Mikrotik : Constant ~1sec drop when roaming. We tried tried RSTP off/on, ROS 7/6.49.2, numerous resets and other tweaking. Constant ~1sec drop. Did you add this for improved roaming?(fine tune the value to your liking) /caps-man access-list add action=accept allow-signal-out-of-range=6s client-to-c...

ivicask

I also hope we don't see anymore same old wifi devices next year, wave2 and wifi 6 products are a must!

ivicask

v7.1 contains routing fixes and improvements in order to fully comply with 6.x setups.

Please give us more detailed changelogs, even if it only says briefly like you wrote now, if we have related issue, we than know to flash new version and check if issue is resolved..

ivicask

Thanks for the reply, now which model should i buy for AP and for wide beam,. My 2 stations are not in the same line, it will maximum 500mtr wide

Depends on distance and separation

How about you just buy another LHG5 and problem solved ?

ivicask

You can't, they come with level 3 licence and don't support ap mode, only bridge, so you can connect only one client. You could upgrade(buy) one to lvl 4 licence than it would work, but again this aps have very narrow beam so they would need to be positioned In same line behind each other in order t...

Search found 524 matches