You can do tha in the simple queue you have target adres and you can limit each address.

For example if you want to block class 10.97.20.x and allow only som of the to have access you can do that like this ip firewall rule forward add src-address=10.97.20.98/32 action=acept ip firewall rule forward add action=drop the last rule will drop everything and if you want to allow clients to ha...

In 2.9 when setting up the hotspot the www port is not changed to 8081 it stays 80 so you can login with default winbox port.

I have upgraded about 6 routers from 2.8.26 to 2.9 two of them were rb230 upgrade procedure was sucesfull but one of the which has two 5213 cards in it after a period of time lock so that one I have to downgrade another one work perfect and other routers which was running as hotspot gateway I upgrad...

Pleas be more specified you can't reach the hotspot page or you get an error when you try to acceess the hotspot .

Best regards the_time

I have sucessfully edit login page for five times or more the procedure is this: 1. download from the router ftp the entire hotspot folder 2. After geting the hotspot folder open for edit login.html I have edited with Macromedia Dreamweaver mx 2004 and have changed nothing from the code just using t...

The chipset I have mentioned can be found on http://www.mikrotik.com or contact sales@mikrotik.com and if you plan to conect on 30 km then you should use 16dbi sectors and 30dbi parabolic antenna .

For stable access point and high data rates I would sugest you to use atheros ar 5212 and sectorized (for exaple 14dbi or 16 dbi) base station with nstreme and poling and on the client side ar5212 or 5211 chipset and if you have long links you should use 30 dbi parabloci antennas and on shorter dist...

I have the same problem conecting 5212 and 5211 on 2.5 Mbps have huge pings .
Very greatfull in a solution .

Exactly I have premision to do this but what I asked is what equimpent should I use for e.x two 16 dbi sectors on base and on client side 30 dbi parabolic anntena or some thing else my question was 30 km away form the access point to connect a client . I think that was an misunderstand .

Thanks.

Hello,
We are trying to build a base station which will work on 5 ghz we need an 180 degrees on about 30 km coverage what equimpent should I use .

Thanks on advice

We are using hotspot in over 15 base and about 1500 clients the only think I would suget to use good hardware and don't use flash disk that they are lover 128 MB.

the_time

So I should send a suppout file to mikrotik support .

We haf the same problem just disable auto-negation and everything work perfect.

We have an 5ghz access point running on router board with atheros 5211 chipset and 10 dbi omni directional anntena with mikrotik v 2.8.21 on client side we have 100 mw atheros card and 23 dbi flat anntena and we can't connect on about 2 km in the same position was working an 50mw ciso aironet card w...

We have an 2.4ghz ap in 800 mhz motherboard wiht 2.8.4 installed and I we have to much trouble .
At 1 mbps everything goes down we have 9 clients conected on it.
Thanks on advice

The hotspot is teh best solution for this we alredy doing this and you can limit in the profile .
Thanks , the_time

We are using the hotspotfor this purpose and we have about 70 clients conected and it works ok but I sugest you to use mikrotik as ap.
thanks

the device that act as a ap is not mikrotik and even when we detect and block the client until they clean the computer we practicing this stragtegy for months but again having trouble.
Again thanks.

I'll tyr to explain my confguration I've got a Mikrotik which is conceted with cisco aironet on mikrotik ap thats not importnt then this router is a hotspot gateway after it is a ap bridge which is conected through ethernet at last times we are having too many problems with atacks(ddos) and viruses,...

Hi evrybody I have a question I have an Mikrotik router and after it has a wireless bridge the reason I am asking is the clients that I have conected probably some of them has viruses that works on port 445 I have blocked this port using firewall rule forward but stil I can see activity betwen clien...

I was hoping that in 2.9 you will support this cards anyway thanks

One of my client has a virus on computer, that router when its conected has hospot and its not loged in but when look on torch the trafic is about 1Mbps that router its limited on 512000 but I really don't know what its going on.
Thanks the_time

Does mikrotim has any plan to support te wireless cards with realtek chipset.
Thanks in answear

I have tried to make some graphicons for bandwith usage, I do something with mrtg but it fails does anybody know something for that.
Best regards the_time

Hello,
I have add a rule that block tcp port 25 so it works fine but I want to relase an ip.
My network configuration are 10.10.10.0 I want to that 10.10.10.5 to get acces to this port.
Thanks

so i've creat a new chain with name "SynFlood" then i create this 0 src-address=0.0.0.0/0:0-65535 in-interface=all dst-address=0.0.0.0/0:0-65535 out-interface=all protocol=tcp icmp-options=any:any tcp-options=syn-only connection-state=any flow="" connection="" content=&...

Hello,
I need some help before some days I have an atack on mikrotik router and evrything goes down now it sems to be an ddos atack does anybody know any way to defend or prevent these kind of atacks.
Thanks