Hello. Try this command on your laptop "netsh wlan show drivers" and post the output to see if your drivers support WPA3 or try to upgrade your wireless drivers. Also don't enable other chipers than CCMP on the router's wifi settings. Here is my edited config name="wifi2" mac-ad...

Some months ago I tried WifiWave2 package, turned on WPA2 PSK and WPA3 PSK. My Galaxy Note 8 could connect, while Xiaomi Mi 11 Lite 5G had issues until I'd turn off WPA3 PSK after which it would work properly. Yesterday I installed 7.3.1 version and Xiaomi Mi 11 Lite 5G don't have any issues connect...

Can confirm that my Xiaomi Mi 11 Lite 5G can connect to WifiWave2 AP on hAP ac3 with WPA3 PSK only and WPA2 and WPA3 combined!
It couldn't connect before if WPA3 were enabled together with WPA2 or if it was enabled by itself, only on WPA2.
Thanks!!

I suppose this would also be some kind of proof that IPsec is working with barely any delay? Yup, IPsec encryption and decryption is not the reason of the jitter. You may try a ping to the CHR's public address using slightly larger packets, matching the size of the ESP ones, to see whether it's the...

I can paste my configurations here but I'll need time to clean them up before posting them here. More eyes usually see more, hence worth it. Are there any other performance tests between routers that I can do beside the usual ICMP ping and bandwidth test? Just sniff at the WAN interface of the 4011...

Are there any known common causes of such issues? The ISP at the location is not perfect but I suppose it shouldn't make such a drastic difference? The location with difficulties in question runs on a WISP provider. The locations that work properly are on LTE and Fiber. Can't deny that it might be ...

Additional info: CHR is 6.49.1, the client on the questionable location is RB4011 with 6.49.2.

I've also now tried setting up IPSEC client on one of the APs (951G) at the location to the CHR, and it's the same issue.. Though the traffic is forwarded through the previously mentioned router.

Hello! I'm from Croatia and I've setup myself a CHR router in Amsterdam. I've connected 3 locations to it with IKEv2 IPSEC, but I'm having a problem with a connection with one of them. Two of the three locations works as expected, pinging to a public IP of a CHR and pinging to a private IP of a CHR ...

My router won't update either from v7.1beta6 to v7.1rc1. It's an RB2011UiAS-2HnD

Does log have anything about it?

yes, it actually does!

15:25:04 system,info router rebooted
15:25:04 smb,info SMB Started
15:25:05 system,error,critical kernel failure in previous boot

Hi, I can't update an RB3011 to the latest rc1 from beta6. RIght after reboot, the router starts on beta6 again. Opening up a terminal it gives me an error about a kernel panic. Any ideas about this? I've also made a support ticket: SUP-58027. My router won't update either from v7.1beta6 to v7.1rc1...

I tried some stuff and it worked.. I'm not sure what fixed it but I set use-ip-firewall to yes at /interface bridge settings, and I edited the default NAT configuration of masquerade, to have a out. interface option set to ether1-gateway

Nothing guys??
I mean I don't know if this question is somewhat stupid.. but I'd like to at least hear from you that this is normal and usual.. All clients appear as 192.168.1.1.. and that should not confuse a server?

Hello everyone. I'm pretty much a noob in networking, and I recently got a Mikrotik Routerboard Lite hAP, because I wanted some QoS control and a friend gave me big help with setting it up. Everything is working fine, but I have this trivial issue I'd like to solve. I have a FileZilla server, and ev...