MikroTik

gyropilot

Please post a copy of your router's configuration file. Do an internet search for “mikrotik export configuration”. An example website result: https://academy.socialwifi.com/hardware-and-installation/setup-faqs/how-to-export-configuration-from-a-mikrotik-device The config file is just text so you can...

gyropilot

Thanks for posting this. I had the same problem between a CSS610 and hAP ac.

gyropilot

can you pls elaborate sir? He's asking you to post a copy of your router's configuration file. Do an internet search for “mikrotik export configuration”. An example: https://academy.socialwifi.com/hardware-and-installation/setup-faqs/how-to-export-configuration-from-a-mikrotik-device The config fil...

gyropilot

I’m a complete newb to fiber optic. I’d like to connected a hAP ac (RB962 router running ROS 6.49.15) and a CSS610 switch (running SWOS Lite 2.18) using SFP modules and a fiber optic cable in between. I tried but I can’t get it to work properly. I bought two 1.25G 1000Base-SX 850nm MMF SFP modules: ...

gyropilot

My hAP ax2 shows the same amount of memory.

gyropilot

Take a look at this post (and the entire thread) for some suggestions…

viewtopic.php?p=928842#p928842

gyropilot

Same problem here.

Until someone advises otherwise, I just used “01:00:00” for both fields. According to the RouterOS manual, I think this means it'll rescan the frequencies every day and reselect the most appropriate channel(s).

gyropilot

Hi there... how to set it up via Winbox please? Thanks a lot! Launch Winbox. Click "Wireless" in menu... screenshot_1110.jpg In the Wireless window that opens, click the "WiFi Interfaces" tab then click on each band (one at a time) to open its Interface screen... screenshot_1111...

gyropilot

In case this helps… I’m assuming you are following ALL other steps outlined in the Mikrotik wiki, then what I found worked best timing wise is to hold the reset button for an additional 5 seconds after the power LED goes out, then release it. The RouterOS device will appear in netinstall within a fe...

gyropilot

cmonty14, I’ve never tried netinstall from Linux… only Windows 10 on an underpowered HP laptop. I never could get my RouterOS devices to reliably show up in netinstall until the day I put an inexpensive, unmanaged Ethernet switch between the laptop and the RouterOS device. Doing that keeps the lapto...

gyropilot

You will need a "managed" switch that has its own interface to configure its ports.

An example is the Mikrotik RB260GS…

https://mikrotik.com/product/RB260GS

gyropilot

I've been using the WiFi on a hAP ac lite and a hAP ac successfully with Apple clients for many years. This includes countless iPhones, iPads, MacBook Pros, Apple TV's and a bunch of non-Apple devices. I don’t know if the hAP ac2 is fundamentally different. My setup: I use “N-only” on the 2.4G band ...

gyropilot

That’s very strange.

I’ve submitted bug reports via support tickets and found Mikrotik to be very responsive and easy to work with.

Maybe you can try cancelling the original ticket and resubmit a new one?

gyropilot

I recently needed to use netinstall on a new hAP ac that was bootlooping after upgrading from ROS v6.49.5 to v7.1.5. I spent days and probably 50 times trying to get the router to show up in netinstall using an HP laptop running Windows 10. I spent hours reading threads about netinstall and trying e...

gyropilot

Strange (but thankfully limited) bootlooping happening here on a hAP ac after upgrading to v7.1.5. I just sent the following bug report through the support website… ——- I just upgraded a new hAP ac directly from ROS v6.49.5 to v7.1.5. It was running normally on v6.49.5. Since installing v7.1.5, if I...

gyropilot

Thanks Jim!

My bad for failing to mention both the device model and firmware version...

It's an RB260GS (CSS106-5G-1S) switch running SwOS v2.13.

John L.
AA7US

gyropilot

Can anyone please explain to me what the marked RX and TX statistics represent on the attached screen capture? Are they packet sizes? Speed buckets?

Thanks you,

John L.

gyropilot

I have the exact same issues. World you mind sharing all the steps necessary to achieve this? Peace ✌🏻 kaherdin, Are you looking for the exact steps needed to have RouterOS use Pi-Hole for DNS? Or are you looking for the steps required to FORCE users behind RouterOS to use Pi-Hole for DNS? If the f...

gyropilot

Successfully updated both RouterOS and Routerboard firmware in a hAP AC Lite (RB952Ui-5ac2nD) from 6.48.4 to 6.49.1 without any problems.

gyropilot

Interesting.

I just checked the interfaces in my hAP AC Lite running 6.45.1 through Webfig and they're all fine.

gyropilot

You've got to setup hairpin nat for the pihole.

Thank you HzMeister. I'll give this a try.

Regards,

John

gyropilot

were does your pihole get its dns? you must allow requests from pihole ip to reach the dns resolver the pihole uses Good point! I knew I must be overlooking something obvious. Pi-Hole's DNS resolver is OpenDNS at 208.67.222.222 and 208.67.220.220. So without additional NAT rules to clear Pi-Hole's ...

gyropilot

Greetings, I'd like to force all users on my single home LAN to use my own Pi-Hole DNS server just in case they've manually configured another DNS server. I found this entry in the MikroTik WiKi which seems like a simple solution: https://wiki.mikrotik.com/wiki/Force_users_to_use_specified_DNS_serve...

gyropilot

Update not working with 952Ui-5ac2nD; downloads file to memory but doesn't apply after reboot

Willian,

Curious if you've fixed this?

John

gyropilot

hello and thank you. i get a message in log that is not enough permissions. what permissions are need it just to reboot after 5 minutes? I encountered the same problem and just checked the “Don’t Require Permissions” checkbox on the script setup screen. Now I don’t know if that’s considered safe fr...

gyropilot

hAP ac lite (RB952Ui-5ac2nD) updated from 6.43.4 to 6.43.7 without any problems here.

gyropilot

Under IP->Firewall->Filter (The position of these rules depends on your current setup. I can't be 100% sure of the position unless I can see your current setup. Should probably be near the end before the deny all rule.) Add Rules (In this order, order is important): src-address: **nanonode ip** dst...

gyropilot

Thanks. Turns out that it's the power supply that's defective or under powered. It's rated at 500 mA. Aha! Glad you found the culprit and thanks for coming back and telling us what it was. Funny thing, I had a similar problem with my hAP ac lite when I first started using it. I bought it for use in...

gyropilot

Got it.

I also should've asked, have you tried using a different PC?

If yes, then the next step might be to try reinstalling RouterOS using Netinstall...

https://wiki.mikrotik.com/wiki/Manual:Netinstall

Failing that, maybe the hAP device is defective.

Regards,

John

gyropilot

Have you tried to access your hAP via WebFig or the CLI (Command Line Interface via SSH) using a direct ethernet connection?

https://wiki.mikrotik.com/wiki/Manual:F ... me_startup

Best regards,

John

gyropilot

This might be getting outside the area of Mikrotik's forum, but after looking at the product I think the security worries might be on the paranoid-ish side. I thought you couldn't be too paranoid with network security? :D Just kidding. Thank you for the suggestions. I appreciate your time. I'll giv...

gyropilot

First off, what device are you trying to connect? Might help me determine the ports needed. Hi Jim, Thanks for the help. This is a Nano-Node from Micro-Node Intl (http://micro-node.com/nano-m1.shtml) for IRLP communication. For it to work correctly the following ports need to be open: Ports 15425 t...

gyropilot

OK, I gave it my best shot but but I can't figure out how to isolate one ethernet port to create a second network under the current RouterOS (with hardware offloading). I found plenty of tutorials and blog posts, but they apply to the old firmware with master/slave switch settings. If anyone can poi...

gyropilot

I will try my best at some advice. Methinks the ham radio needs to be on a different subnet and not on the same bridge as the homeLAN. Your firewall rules ((FORWARD)) should include a drop all rule at the end. Your firewall rules ((FORWARD)) should include a 192.168.x.x (your pc on homelan) to 192....

gyropilot

Greetings, I have a super simple network setup in our RV which consists of a single hAP ac Lite (RB952Ui-5ac2nD) running RouterOS v6.43.2. WAN is ether1 or the single USB port to a cellular LTE modem. either2-either5 and wlan1-wlan2 are bridged into a single LAN. Hardware offloading is being used on...

gyropilot

Updated the following devices from ROS v6.39.1 to v6.39.2 with no difficulties noted:

hAP ac Lite
Metal 52 ac

gyropilot

Hi Normis, Thanks for the quick reply. I think I just stumbled upon the cause of this problem... I found the "Allow Remote Requests" button was NOT checked in the Metal 52 ac's DNS settings. Once that was checked, I immediately got the public WiFi network's landing page. Prior to doing tha...

gyropilot

Greetings all, I'm using a Metal 52ac mounted externally on an RV roof to connect to public WiFi networks. The Metal is connected via an Ethernet cable to a hAP ac Lite located inside our RV where we have a WiFI LAN. I normally use Quick Set in CPE mode in the Metal to connect to the public WiFI net...

gyropilot

Updated the following devices today to ROS v6.39.1 with no difficulties:

hAP ac Lite
Metal 52 ac

gyropilot

This is one a Mikrotik CCR DHCP server handing out public IP addresses on a pool. I have a client, I think an Apple router MAC 20:C9:D0:11:56:F0, that the DHCP says "declines IP address x.x.x.x" several times a second. ... Anyone seen this? sterling, I see this behavior often with my hAP ...

gyropilot

Just obtained a used Novatel U620L (USB620L) modem and it's working perfectly with my hAP ac Lite. I first plugged the U620L in a Windows laptop in order to access the modem's building-in web console to set the modem to auto-connect to the cellular network. Next I plugged the modem into my hAP ac Li...

gyropilot

1) In the hAP ac lite spec. sheet from routerboard.com website, only says [PoE in : Yes], but didn't give out standard like other products listed 802.3af/at. So what kinda power source does hAP ac lite require, can anyone give me a clear answer? The hAP ac Lite spec sheet says: "Yes (Ether5), ...

gyropilot

FYI - I am sometime planning to re-write a 2'nd newer version of my netwatch-script-reboot-on-ping-loss program. Hi Tom, I like the idea of adding the option for a second IP address to ping against to make double sure failure of the primary IP address isn't causing a false WAN failure. I'm using a ...

gyropilot

Hi Tom, I'm brand new to scripting and have found your examples very helpful. I appreciate you sharing them. Question: Are the quotes in the following line really supposed to be there? :if ($"goodpings" = 0 ) do={ I couldn't get the script to work until I removed them. Thanks in advance, J...

gyropilot

Thank you for the reply Larsa.

gyropilot

I'm brand new to scripting and could use some help... Can anyone point me to a simple script which essentially duplicates Netwatch (pinging an IP out on the WAN), but instead of executing an action after only one ping failure, have it test for multiple ping failures over a given period of time befor...

gyropilot

Not sure if related but is your "/system clock print" correct?

Yes... mine is. It's kept up to date from an SNTP server.

gyropilot

I'm seeing the same thing through webfig on my hAP AC Lite. It's not just pppoe but every kind of link status date / time stamp.

gyropilot

For anyone who happens upon this old thread...

I'm happy to report that as of RouterOS v6.38, the Pantech UML295 is now fully supported as an LTE device.

I have one working perfectly in the USB port of my hAP ac Lite with Verizon as the carrier.

gyropilot

What's with the false critical messages in 6.38rc15 on my 922UAGS-5HPacD?

Critical cpu overclocked
Critical memory overclocked

I'm also getting the "cpu overclocked" error after boot on my RB952 hAP ac lite running 6.38rc14, but not the "memory overclocked" error.

John

gyropilot

I've also tried the 6.38rc14 and had the same experience. I ended up downgrading to 6.35.4 and all is well. I have a UML295 with a static ip and haven't figured out how to access the mAP2nD from the outside. This is to be a remote installation where access to the internal network in necessary. Any ...

gyropilot

Can you please send supout.rif to support@mikrtik.com from latest version and verwin where lte interface is presented ?

Done!

Thank you Kristaps.

Best regards,

John

gyropilot

Bummer!

Just downloaded and installed 6.38rc14 and unfortunately my particular Pantech UML295 still doesn't show up as an LTE interface.

John

gyropilot

Proxicast makes a tiny device cellular modem bridge called the PocketPORT 2. You can plug just about any USB cellular modem in one end and an Ethernet cable into the other end. The Ethernet cable can then be a WAN source for any router. See http://proxicast.com/products/products.htm for details. John

gyropilot

The Verizon Pantech UML295 USB LTE modem should work just as soon as RouterOS v6.38rc14 is released. It used to work, but something broke after ROS v6.35.4.

See the thread...

http://forum.mikrotik.com/viewtopic.php?f=2&t=72286

...for more info.

Best regards,

John

gyropilot

Please try latest 6.38rc14+ PANTECH modem issue should be fixed

Thank you Kristaps. This is great news!

I'm looking forward to testing that RC version when available.

Best regards,

John

gyropilot

Curiously, although officially supported in 6.37 my experience has been that the Pantech UML295 does not work at all (and is not recognized by ROS as an LTE device) after 6.35.4. Thanks for your post. My experience mirrors yours... So far I've been working with support concerning this problem for a...

gyropilot

Sorry to dredge up an old thread, but I've had no luck getting RouterOS version 6.38rc7 to recognize my Pantech UML295 USB modem as an LTE interface device. According the RouterOS release notes, starting with version 6.37 this USB modem is supposed to be officially supported. Here's the relevant exc...

gyropilot

I had similar behavior with a brand new hAP ac lite (RB952) I recently installed. The problem turned out to be a faulty 3rd party voltage regulator in a power adapter I was using. Try a different / known good power supply with sufficient current output and see if the rebooting disappears. Best regar...

gyropilot

FOLLOWUP - I've figured out the root cause of the frequent reboot problem... No surprise but there's absolutely nothing wrong with my MikroTik RB952 hAP ac lite router! The problem turned out to be a faulty user-supplied 12v DC power cord. You see I thought I was using a simple pass-though cord to d...

gyropilot

Also - Don't forget that having two WANs means you need two sets of filter rules. Well, in the newer releases you can use interface lists, with allows for one set... but that's in networking 102... we'll stick to 101 for now. Thanks Dave for your kind comments and helpful suggestions. Your comment ...

gyropilot

Remove the wifi from the LAN bridge... Dave, As I try to wrap my head around this concept, I'd like to double check that my understanding is correct... 1. I DON'T necessary need to create a second bridge in RouterOS, because a bridge is used only to tie LAN ports together (if that's needed and/or d...

gyropilot

Hi all, I'm on my 3rd day of owning a RB952Ui-5ac2nD-US hAP ac lite. While I only know basic networking, through lots of searching and reading the Wiki and forum, I've figured out how to get the router setup with both a WAN source connected to ether 1 and a USB LTE cellular modem. I can switch betwe...

gyropilot

My solution was a 12 to 24v step up power supply.

I happen to have one of those on hand for use with a printer requiring 24v DC. I'll also give it a try with the RB952 router.

Have a great day,

John

gyropilot

Also, the unit should have come with a 24v 1.2A supply - I've found that the "ac" units have issues with 12v power. I have several hAP ac's that also reboot from the watchdog timeout if they aren't getting enough power. I think you nailed it Dave! I'm a full-time RV'er and had the router ...

gyropilot

Greetings all, I'm brand new to MikroTik products with a new RB952Ui-5ac2nD-US hAP ac lite I just bought. I'm running with a basic, almost stock, router setup using only the 5GHz WiFi (2.4GHz disabled) and a WAN source over ether1. I only have 1 to 3 wireless clients connected to the router. I'm usi...

Search found 66 matches