MikroTik

Torontobb

GRE is point-to-point [2] and can emulate an Ethernet segment, but really only one link. By one link you mean GRE can be one tunnel? (maybe link is the right term). I think you mean I can't have multiple GRE connections running at the same time. If so that will be limiting to me because I want to m...

Torontobb

Hi, I want to setup layer2 spanning over layer3. I see that IPIP has the lowest overhead of any protocol available out there including those of VPNs and ones like VxLAN and EoIP. What can VxLAN and EoIP can do that IPIP tunnel can not do? If none then why people want to use VxLAN or EoIP while IPIP ...

Torontobb

Still nothing on this from Mikrotik. Should be very quick to add logs. Are they just lazy?

Torontobb

I want a tunnel protocol supported by RouterOS / Mikrotik devices that has the LEAST overhead that creates a full Layer-2 experience with bridge and vlan capabilities. I also want it to be supported by Bonding so I can bond multiple of these tunnels for higher speeds. I do not need any encryption. I...

Torontobb

Hi, I have a location that only provides 120Mbps download / 20 Mbps upload but I can bring in 5 connections and connect them to a Mikrotik router. Once these connections are put in, I would like to use their collective download and upload speed to get at least 100Mbps upload for my EoIP tunnel. Is t...

Torontobb

beware hap ac lite only have 100m bit ethernet interfaces that can be a limiting factor in your setup if you concentrate traffic in one ethernet interface also keep in mind this device only has 1 core 650mhz cpu, depending on your setupscenario cpu resources cannot be enough to do bandwidth control...

Torontobb

I am play with a "hAP ac lite" unit and I have 120 Mbps download and 20 Mbps upload. How to divide the bandwidth so that each VLAN below gets this amount of bandwidth at *all* times: VLAN 5 = 30 Mbps download / 5 Mbps upload VLAN 6 = 30 Mbps download / 5 Mbps upload VLAN 7 = 30 Mbps downlo...

Torontobb

It is not possible for certificate, you have to export them one by one unfortunately.

How about other tasks? I do a bunch of tasks and I want to see *only* those tasks in commands style without having to sift through the whole configuration export. Possible?

Torontobb

Anyone?

Torontobb

How often do you change your wan interface name that this is such a big issue for you?

What is technically wrong is wrong no matter how you spin it. I would write about me changing an interface many times if that was an issue but it is not. Issue is explained really well and it IS AN ISSUE.

Torontobb

How can you tell it is not working ?

Other routes show "ping" in front of the route in status but this one does not.

Torontobb

With a PPPoE user, I will agree with way it is, if anything changed, restart service.

Why? what is your reason for that? Does the name of PPPoE service have to be sent to provider? if not, how is it different from any other interface name?

Torontobb

That "arbitrary name" as you call it, is also used in other places in RouterOS and some stuff depend on it (firewall rules or whatever). They can't work using some "name" that doesn't exist (if you change it). Just my two cents on this. Why does it bother you? Changing ANY other...

Torontobb

To connect all links with public addresses. This is the only way.

How??

Torontobb

I have a dynamic route added to Routes but don't see check-gateway working for OpenVPN. It works for a pptp but don't see it for OpenVPN or ISP...what is the reason and can it be turned ON on all dynamically added routes?

Torontobb

I am doing a bunch of things to create Certificates for OpenVPN and then transfer them to another server and make Mikrotik an OpenVPN client to the OpenVPN server... I know how to do all this on GUI. Is there anyway that I can see an exact command line of what I did on GUI so I can make a script on ...

Torontobb

I like the DynDNS feature of Mikrotik. Specially, that it allows the 1 minute refresh interval time. However, I have some installations behind other routers and I would love to be able to reach my Mikrotiks without having to do NAT forwards on other firewalls to reach it. A- Is there anything built ...

Torontobb

RESOLVED: None of suggestions above worked. I ended up getting a router that support Rx and Tx limit or just Tx limits and did: /interface ethernet set bandwidth=unlimited/5000k ether4 /interface ethernet set bandwidth=unlimited/12000k ether5 That simply allowed for both upload and download restrict...

Torontobb

1) Backups are stored in Latvia
2) No 3rd parties
3) only aes-sha256 encrypted backup files are accepted

Juts for the kicks, is it possible to look at the source code that encryption applies? or it's not possible to see sourcecode of RouterOS?

Torontobb

Changing PPPoE client name disconnects PPPoE and re-connects - WHY?
This is just an arbitrary name for the PPPoE client that is only relevant to local setup and nothing to do with ISP. Why does it disconnect and re-establish client?

This happens on Winbox when name is changed on GUI.

Torontobb

I may have missed that in the previous posts, but it seems to me that the configuration by @IPANetEngineer lacks a significant bit of information - in order for queues to work also for L2 frames, in interface bridge settings , use-ip-firewall must be set to yes ; in order that PPPoE frames were han...

Torontobb

Is this thread and its usefulness fully dead?

Torontobb

Any bandwidth test servers? All that is posted on the forum is dead.
Looking for one with 1Gbps test support.

Torontobb

Any gurus can comment on this?

Torontobb

Tested, not connecting. Can't find any working public server on this forum.

Torontobb

Actually its really simple... Something is preventing it from working on your configuration... Thanks for feedback. Have you tested this in your lab that you can say for sure? The specific configuration no... However i have used simple queues, really, in hundreds of configurations... So i know they...

Torontobb

Actually its really simple... Something is preventing it from working on your configuration... Thanks for feedback. Have you tested this in your lab that you can say for sure? This is a factory fresh config and up to date router with only these commands so I doubt what you said holds (the something...

Torontobb

Your queues look fine... in the advanced tab of the parent queue add as type pcq upload default and pcq download default... Also specify your target in your third router... Then test again... Setting to PCQ Default for both upload and download did not make a difference. Also setting Target to ether...

Torontobb

Your queues look fine... in the advanced tab of the parent queue add as type pcq upload default and pcq download default... Also specify your target in your third router... Then test again... Setting to PCQ Default for both upload and download did not make a difference. Also setting Target to ether...

Torontobb

Here are some example configs and a diagram that should point you in the right direction. A few notes on this - I tried to keep the config as simplistic as possible since you're dealing with very low speeds. There are more efficient ways to do this, but it requires more config. Also, I used 10M dow...

Torontobb

Did you finally add queues for the PPPoE? Can i see those queues? I am not sure what you mean by that. Can you add commands please like IPANETEngineer did. PPPoE is done on "3rd Party Router". This is my current settings: /interface bridge add name=Shared-LAN /interface bridge port add br...

Torontobb

Anyone can comment why upload speed limit works but not download?

Torontobb

If I read the OP correctly, he does not have control of the PPPoE server. I am not sure what control means in this context but PPPoE server is on ISP side. Of course, I can run a PPPoE server on Mikrotik too and maybe(?) then pass public IP to 3rd Party Router but seems like your method is the best...

Torontobb

Here are some example configs and a diagram that should point you in the right direction. A few notes on this - I tried to keep the config as simplistic as possible since you're dealing with very low speeds. There are more efficient ways to do this, but it requires more config. Also, I used 10M dow...

Torontobb

Assign a rate limit in the profile of the PPPoE server...
https://wiki.mikrotik.com/wiki/Manual:P ... r_Profiles
Check the rate limit in the above link..

Is rate limit same as queues?
On IRC channel people said that Queues limits will break PPPoE authentication. Is that true?

Torontobb

Layer 2 means no routing.. Data link layer.. Mac addresses.... I understand but new to Mikrotik so what is the command that should run to make eth1 and eth2 prepared for this? If you Bridge two interfaces then they are on the same Layer 2 network. For example, i could have my ISPs router connected ...

Torontobb

Layer 2 means no routing.. Data link layer.. Mac addresses....

I understand but new to Mikrotik so what is the command that should run to make eth1 and eth2 prepared for this?

Torontobb

1. You said you want your internal router to PPPoE authenticate with your ISP right? For this to happen you should have a layer2 tunnel between your internal router and the ISPs router... What should be the port configuration for Layer 2 for: ISP Modem >(Layer 2)>Mikrotik>(Layer 2)>Internal Router ...

Torontobb

You can do that too..

1- What do you mean by that? What is the alternative?
2- Can bandwidth shaping happen for Layer 2 as well?

Torontobb

Create a PPPoE client...

Create PPPoE client on what device? and how? Not sure what you mean. Internal Route has only one way of connecting PPPoE. Do you mean I should do PPPoE authentication on Mikotik and pass the public IP to Internal Router?

Torontobb

Anyone?

Torontobb

Yes, it is possible. RouterOS is not going to be a limitation and CPU power in a Hex is plenty for distributing those 8 mbps. Just use queues and separate the interfaces from the switch chip. Thanks for confirmation. First step, how should I configure a Mikrotik interface to allow the Internal Rout...

Torontobb

The question is if you are able to make PPPoE connection from "internal" router to receive public address if there is no Mikrotik "in the middle"? What do Mikrotik should do in your opinion? Yes, internal router CAN PPPoE authenticate and get a public IP from ISP while it's conn...

Torontobb

Anyone?

Torontobb

Hi Everyone, Please see attached hand drawn diagram. Right now there is no Mikrotik installed but I would like to add it like I drew on the diagram. I would like Mikrotik to dedicated 5 Mbps UP/DOWN for phones at all times and to also act as a bottleneck *switch* OR *router* and allows PPPoE to pass...

Torontobb

Hey sorry I was not watching this email.
I can post our configs here once you ask your specific questions.

How many users are going to support and what model of MT are you using?

Torontobb

If this app is not open source how can one be sure that data and access to routers are not logged, shared, or misused?

What is the guarrantee here to expose oneself to a third private party?

This is a serious concern.

Torontobb

Yes, we got it done and working well. Quiet a bit of work though. However, I can confirm it works.

Torontobb

Hello, I have an inside* CactieZ server that is a client to my CCR1036 edge router and I also have another outside* CactieZ that lives on Amazon. I want both to be able to connect to my CCR1036 and keep it monitored. What do I need to do in terms of firewall to allow this to open? I had the SNMP por...

Torontobb

Hello, I have an OpenVPN profile made with certificates etc. When I try to connect from OpenVPN client from Windows I get the following. Must I open some ports for OpenVPN? I understand that OpenVPN on Mikrotik doesn't support TUN and only does TCP (sigh): My OpenVPN profile: 2 name="Opevpn_Pro...

Torontobb

By test along the way you mean do a tracert and then my ping test each of those hops?

Thanks,

Torontobb

Idlemind - I did exactly that on client end modem and found 1464 to be the largest MTU so with 28 added that is 1492. I have set my fiber interface to 1492 and no luck. I can ping speed test.net but can't browse it. To give some background this is two fiber coming into my CCR1036. One from DSL whole...

Torontobb

I can confirm that MikroTik works with L2TP/LNS/LAC fully and as expected. I do have an issue with not being able to browse all sites and my provider says it's an MTU of 1622 on the interface but is not sure about VLAN2020 and L2TP tunnel. I am assuming I am having an MTU issue so how can I go about...

Torontobb

Thanks nz_monkey. What you wrote under #1 is what is left to do?

See the post from "PDF" stating the 10mbit limit.

Thanks

Torontobb

1- nz_monkey, can you please detail what you mean by basic? What is left to do?

2- what is the release timeline for v7?

Torontobb

So finally is LAC/LNS supported or not? If this is a 10mbsp limit or if supports some Cisco and not Juniper or some products and not others then it can't be reliable as a carrier grade product. 1- What is the licensing pricing for this? 2- Can someone sum up if this is really working for an ISP or j...

Torontobb

So Bell Wholesale is recommending Cisco or Juniper for this. Reading thi thread I am confused if LNS and LAC is fully supported or not? If it's a maximum of 10mbps or doesn't support some geography then this is not service ready. 1- Can someone please weigh in as a whole and specifics of this so we ...

Search found 57 matches