I'm trying to query the SFP Parameters which are available via CLI with a command like this:
Code: Select all
> /interface/ethernet monitor sfp-sfpplus1
name: sfp-sfpplus1
status: no-link
auto-negotiation: disabled
sfp-module-present: yes
sfp-rx-loss: yes
sfp-tx-fault: no
sfp-type: SFP/SFP+/SFP28
sfp-connector-type: LC
sfp-link-length-sm: 10km
sfp-vendor-name: FLEXOPTIX
sfp-vendor-part-number: P.B1696.10.AD
sfp-vendor-revision: A
sfp-vendor-serial: 1234
sfp-manufacturing-date: 22-09-09
sfp-wavelength: 1270nm
sfp-temperature: 48C
sfp-supply-voltage: 3.286V
sfp-tx-bias-current: 40mA
sfp-tx-power: -2.35dBm
I place a GET request to http://172.16.50.1/rest/interface/ethernet/sfp-sfpplus1 and receive this:
Code: Select all
{
".id": "*1",
"arp": "enabled",
"arp-timeout": "auto",
"auto-negotiation": "false",
"bandwidth": "unlimited/unlimited",
"default-name": "sfp-sfpplus1",
"disabled": "false",
"driver-rx-byte": "0",
"driver-rx-packet": "0",
"driver-tx-byte": "0",
"driver-tx-packet": "0",
"full-duplex": "true",
"l2mtu": "1580",
"loop-protect": "default",
"loop-protect-disable-time": "5m",
"loop-protect-send-interval": "5s",
"loop-protect-status": "off",
"mac-address": "4C:5E:0C:XX:XX:XX",
"mtu": "1500",
"name": "sfp-sfpplus1",
"orig-mac-address": "4C:5E:0C:XX:XX:XX",
"running": "false",
"rx-1024-1518": "0",
"rx-128-255": "0",
"rx-1519-max": "0",
"rx-256-511": "0",
"rx-512-1023": "0",
"rx-64": "0",
"rx-65-127": "0",
"rx-align-error": "0",
"rx-broadcast": "0",
"rx-bytes": "0",
"rx-code-error": "0",
"rx-fcs-error": "0",
"rx-flow-control": "off",
"rx-ip-header-checksum-error": "0",
"rx-jabber": "0",
"rx-length-error": "0",
"rx-multicast": "0",
"rx-overflow": "0",
"rx-packet": "0",
"rx-pause": "0",
"rx-tcp-checksum-error": "0",
"rx-too-long": "0",
"rx-too-short": "0",
"rx-udp-checksum-error": "0",
"sfp-rate-select": "high",
"sfp-shutdown-temperature": "95",
"speed": "1Gbps",
"tx-1024-1518": "0",
"tx-128-255": "0",
"tx-1519-max": "0",
"tx-256-511": "0",
"tx-512-1023": "0",
"tx-64": "0",
"tx-65-127": "0",
"tx-broadcast": "0",
"tx-bytes": "0",
"tx-carrier-sense-error": "0",
"tx-deferred": "0",
"tx-excessive-collision": "0",
"tx-fcs-error": "0",
"tx-flow-control": "off",
"tx-late-collision": "0",
"tx-multicast": "0",
"tx-multiple-collision": "0",
"tx-packet": "0",
"tx-pause": "0",
"tx-single-collision": "0",
"tx-underrun": "0"
}
The SFP related parameters are mostly missing. Any idea how to place a GET request returning something similar like monitor on the CLI?
