i use routeros to make it to be a station to connect to my neighbor's wireless network, but it display"failed to select network". but the ros can connect other router wireless. i can connet the network by windows xp or windows7 system. please help me? thanks(i have tried 4.17 and 5.2 version)

attach more configration picture, help me. thanks very much

Your log shows that you are not allowed to connect to the specific mac address outlined in red due to an entry in the connect-list.
Please post "/interface wireless connect-list print".

[admin@MikroTik] /interface wireless connect-list> pri
Flags: X - disabled
0 X interface=AccessPoint connect=yes mac-address=00:19:E0:AF:DC:4E ssid="Tenda" signal-range=
security-profile=Tenda wireless-protocol=any

1 X interface=AccessPoint connect=yes mac-address=00:27:19:32:5C:4A ssid="TP-LINK_325C4A" sign
area-prefix="" security-profile=week wireless-protocol=any

2 X interface=AccessPoint connect=yes mac-address=94:0C:6D:66:C6:D2 ssid="yujuan" signal-range
security-profile=yujuan(hide) wireless-protocol=any

3 interface=AccessPoint connect=yes mac-address=82:C7:14:4F:2B:38 ssid="ChinaNet-vhu3" signa
area-prefix="" security-profile=ChinaNet-vhu3 wireless-protocol=any

i post my wlan card configration

[admin@MikroTik] /interface wireless> pri
Flags: X - disabled, R - running
0 ;;; Inside
name="AccessPoint" mtu=1480 mac-address=00:0A:EB:A2:3F:89 arp=enabled
interface-type=Atheros AR5212 mode=station ssid="ChinaNet-vhu3" frequency=2447
band=2ghz-b/g channel-width=20mhz scan-list=default wireless-protocol=any
antenna-mode=ant-a wds-mode=dynamic wds-default-bridge=none wds-ignore-ssid=no
bridge-mode=enabled default-authentication=yes default-forwarding=yes
default-ap-tx-limit=0 default-client-tx-limit=0 hide-ssid=no
security-profile=ChinaNet-vhu3 compression=no


help me! thanks very much

Try disabling rule 3 in your connect-list. You still have "default-authentication=yes" on that interface, so it should connect without an entry in the connect-list.

ADD: Is this a wds bridge connection? The station has wds-mode=dynamic. Is the AP set for wds?

I see you posted the security profile above. It appears you have too much selected. Only one type of security should be selected. Check your ap and see what it uses. It should use only one type of security. Then match that in this station.

i have Tried disabling rule 3 in my connect-list, but it's also not working. my network card is not wds bridge connection, i have changed wds-mode=disable, it's not a AP, just a station to connect to my neighbore's wireless. i changed my profile to just one type.
1. i disable connect-list, it's not working
2. i disable default-authentication=yes, but enable connect-list rule 3, it's also not working
help me brother. i don't know what's wrong with my ros, i can use many computers and phone connect to my neighbor's wifi.

some configration printe
=============
[admin@MikroTik] /interface wireless> pri
Flags: X - disabled, R - running
0 ;;; Inside
name="AccessPoint" mtu=1500 mac-address=00:0A:EB:A2:3F:89 arp=enabled
interface-type=Atheros AR5212 mode=station ssid="MikroTik"
frequency=2412 band=2ghz-b channel-width=20mhz scan-list=default
wireless-protocol=unspecified antenna-mode=ant-a wds-mode=disabled
wds-default-bridge=none wds-ignore-ssid=no bridge-mode=enabled
default-authentication=yes default-forwarding=yes default-ap-tx-limit=0
default-client-tx-limit=0 hide-ssid=no security-profile=default
compression=no
==============
[admin@MikroTik] /interface wireless connect-list> pri
Flags: X - disabled
0 X interface=AccessPoint connect=yes mac-address=82:C7:14:4F:2B:38
ssid="ChinaNet-vhu3" signal-range=-80.80 area-prefix=""
security-profile=ChinaNet-vhu3 wireless-protocol=any
============
[admin@MikroTik] /interface wireless security-profiles> pri
0 name="ChinaNet-vhu3" mode=dynamic-keys authentication-types=wpa2-psk
unicast-ciphers=aes-ccm group-ciphers=aes-ccm
wpa-pre-shared-key="******" wpa2-pre-shared-key="******"
supplicant-identity="******" tls-mode=no-certificates
tls-certificate=none static-algo-0=none static-key-0="" static-algo-1=none
static-key-1="" static-algo-2=none static-key-2="" static-algo-3=none
static-key-3="" static-transmit-key=key-0 static-sta-private-algo=none
static-sta-private-key="" radius-mac-authentication=no
radius-mac-accounting=no radius-eap-accounting=no interim-update=0s
radius-mac-format=XX:XX:XX:XX:XX:XX radius-mac-mode=as-username
radius-mac-caching=disabled group-key-update=5m
management-protection=allowed management-protection-key=""

Does the neighbor's wifi ap have wpa2-psk set as the security setting? Same wpa2 key? If the key doesn't match, no connection.

of course, my neighbour's wifi is wpa2-psk with AES encryption type. i am using now. i sure the key is right

The only thing I see that is different is the "caps 0x31" value for that AP in your log. Mine show "caps 0x421". The rest of yours show "caps 0x431". I have requested that info from support, but it may be a couple days since it is the weekend.

Anyone else know what that means, and how to decode that hex number?

Otherwise, I am out of ideas.

whatever, i thank you very much.

Your posts are conflicting also, so it is difficult to tell what your current setup is. One post:

[admin@MikroTik] /interface wireless> pri
Flags: X - disabled, R - running
0 ;;; Inside
name="AccessPoint" mtu=1480 mac-address=00:0A:EB:A2:3F:89 arp=enabled
interface-type=Atheros AR5212 mode=station ssid="ChinaNet-vhu3" frequency=2447
band=2ghz-b/g channel-width=20mhz scan-list=default wireless-protocol=any
antenna-mode=ant-a wds-mode=dynamic wds-default-bridge=none wds-ignore-ssid=no
bridge-mode=enabled default-authentication=yes default-forwarding=yes
default-ap-tx-limit=0 default-client-tx-limit=0 hide-ssid=no
security-profile=ChinaNet-vhu3 compression=no

Then a couple posts later:

[admin@MikroTik] /interface wireless> pri
Flags: X - disabled, R - running
0 ;;; Inside
name="AccessPoint" mtu=1500 mac-address=00:0A:EB:A2:3F:89 arp=enabled
interface-type=Atheros AR5212 mode=station ssid="MikroTik"
frequency=2412 band=2ghz-b channel-width=20mhz scan-list=default
wireless-protocol=unspecified antenna-mode=ant-a wds-mode=disabled
wds-default-bridge=none wds-ignore-ssid=no bridge-mode=enabled
default-authentication=yes default-forwarding=yes default-ap-tx-limit=0
default-client-tx-limit=0 hide-ssid=no security-profile=default
compression=no

The second one was not going to connect to the ChinaNet AP. Wrong ssid and security profile.

sorry, this one is my configration.

[admin@MikroTik] /interface wireless> pri
Flags: X - disabled, R - running
0 ;;; Inside
name="AccessPoint" mtu=1480 mac-address=00:0A:EB:A2:3F:89 arp=enabled
interface-type=Atheros AR5212 mode=station ssid="ChinaNet-vhu3" frequency=2447
band=2ghz-b/g channel-width=20mhz scan-list=default wireless-protocol=any
antenna-mode=ant-a wds-mode=dynamic wds-default-bridge=none wds-ignore-ssid=no
bridge-mode=enabled default-authentication=yes default-forwarding=yes
default-ap-tx-limit=0 default-client-tx-limit=0 hide-ssid=no
security-profile=ChinaNet-vhu3 compression=no

I see you have "wds-mode=dynamic" in the station. Is the ap using wds also? If not, ADD: You shouldn't even have to look at the ap about the wds setting. Did you set up wds when you connected with the Windows computers? Did you change the mtu setting there also?

I don't know the brand of AP, but you might want to check the log on that unit. Maybe something there.

i have set wds-mode=disabled, but also can't work normaly. my AP is Huawei HG255d, chinatelcom send me

I think you should start over with that router. Then set only what you need. Just the basics.

/interface wireless (band and ssid only)
/interface wireless security-profiles (wpa2-psk and aes only)
/ip dhcp-client

Once you get the connection established, then continue from there.
If you can connect with a Windoze computer, this should not be that difficult.

i reset ros configration and config ros like what you post me, it's still not working

[admin@MikroTik] /interface wireless> pri
Flags: X - disabled, R - running
0 name="wlan1" mtu=1500 mac-address=00:0A:EB:A2:3F:89 arp=enabled
interface-type=Atheros AR5212 mode=station ssid="ChinaNet-vhu3"
frequency=2447 band=2ghz-b/g channel-width=20mhz scan-list=default
wireless-protocol=unspecified antenna-mode=ant-a wds-mode=disabled
wds-default-bridge=none wds-ignore-ssid=no bridge-mode=enabled
default-authentication=yes default-forwarding=yes default-ap-tx-limit=0
default-client-tx-limit=0 hide-ssid=no security-profile=profile1
compression=no
======
[admin@MikroTik] /interface wireless security-profiles> pri
0 name="default" mode=none authentication-types="" unicast-ciphers=""
group-ciphers="" wpa-pre-shared-key="" wpa2-pre-shared-key=""
supplicant-identity="MikroTik" eap-methods=passthrough
tls-mode=no-certificates tls-certificate=none static-algo-0=none
static-key-0="" static-algo-1=none static-key-1="" static-algo-2=none
static-key-2="" static-algo-3=none static-key-3=""
static-transmit-key=key-0 static-sta-private-algo=none
static-sta-private-key="" radius-mac-authentication=no
radius-mac-accounting=no radius-eap-accounting=no interim-update=0s
radius-mac-format=XX:XX:XX:XX:XX:XX radius-mac-mode=as-username
radius-mac-caching=disabled group-key-update=5m
management-protection=disabled management-protection-key=""

1 name="profile1" mode=dynamic-keys authentication-types=wpa2-psk
unicast-ciphers=aes-ccm group-ciphers=aes-ccm wpa-pre-shared-key=""
wpa2-pre-shared-key="kkc4vepw" supplicant-identity=""
tls-mode=no-certificates tls-certificate=none static-algo-0=none
static-key-0="" static-algo-1=none static-key-1="" static-algo-2=none
static-key-2="" static-algo-3=none static-key-3=""
static-transmit-key=key-0 static-sta-private-algo=none
static-sta-private-key="" radius-mac-authentication=no
radius-mac-accounting=no radius-eap-accounting=no interim-update=0s
radius-mac-format=XX:XX:XX:XX:XX:XX radius-mac-mode=as-username
radius-mac-caching=disabled group-key-update=5m
management-protection=allowed management-protection-key=""
========
[admin@MikroTik] /ip dhcp-client> pri
Flags: X - disabled, I - invalid
# INTERFACE USE-PEER-DNS ADD-DEFAULT-ROUTE STATUS ADDRESS
0 wlan1 yes yes searching...
========
simple ros log screen ========
debug log screen

"failed to join" is usually due to an invalid key. The AP is wpa2-psk, and not wpa-psk, correct? That key is case sensitive.

If that isn't it, maybe someone else will see something I don't see.

anyone can help me? i love use Routeros,but i can't connet to Neighbor‘s wirless network with ROS. my neighbor is using Shanghai Telecom wireless router, i can use DD-WRT or Tomato connect to the wireless router, but only ROS Connection fails, I am no idea to solve the problem now, anybody help me !!!!!!!!!