v6.0 released

Tue May 21, 2013 8:06 am

What's new in 6.0 (2013-May-17 14:04):

*) ipsec - added /peer passive option which will prevent starting ISAKMP negotiation
and signifies xauth responder/initiator side;
*) RouterBOARD - default wireless config now includes password - serial number;
*) lte - support YOTA WLTUBA-107;
*) console - fixed crash when variable name was not specified for
*) hotspot - added mac-cookie login method;
http://wiki.mikrotik.com/wiki/Manual:Ho ... MAC_Cookie
*) lcd - show a message when system shutdown is complete;
*) lcd - added Log screen which is accessible through the Main Menu
and shows log messages where action=echo;
*) ipsec - added pre-shared-key-xauth and rsa-signature-hybrid authentication methods;
*) increased max l2mtu on CCR to 10226 bytes;
*) fixed crash on RB1200;
*) fixed bonding - did not work after remove, undo;
*) fixed queues - router could become unresponsive when configuring queues;

erebusodora · Tue May 21, 2013 8:23 am

After upgrade from 5.25 to 6.0 PPPoE client disconected after 3 hours on x86. System reboot PPPoE client conect again. Back to 5.25 all is OK.

EgyCom · Tue May 21, 2013 8:41 am

Bonding with ARP monitoring is not working, disable ARP monitoring or change to MII solve the problem, tested on 750g, 750gl, 1000AH and 1100AHx2

PietRetief · Tue May 21, 2013 9:26 am

Hi,

I just upgraded from Ros5.25 on a RB433, RB750G, 5Ghz RB711G and SXT

All of them were running firmware 3.07 (that came with Ros5.25), but now the SXT and 711 state that their latest available firmware is 3.02?

Is it safe to run 3.07 on them or should I downgrade to 3.02 for those 2 routers.

Regards.

Arnold2222 · Tue May 21, 2013 9:29 am

You mean 6RC15.... for 6.0 it has too many issues

on RB 450G it miss like 4 packages which made my RB unreachable.

I made that firmware "downgrade" on RB 750 works fine

Tue May 21, 2013 9:36 am

PietRetief, both firmwares are working ok. We will update to the newer firmware for those boards in next RouterOS release.

Tue May 21, 2013 9:38 am

You mean 6RC15.... for 6.0 it has too many issues

on RB 450G it miss like 4 packages which made my RB unreachable.

I made that firmware "downgrade" on RB 750 works fine

what packages are missing? when you upgrade, you must upload the packages you need, if you didn't upload them, they will not be installed.

PietRetief · Tue May 21, 2013 10:06 am

@uldis, thank you

So far so good, wireless links and OSPF are behaving well.

Chrisdewit · Tue May 21, 2013 10:21 am

My Simple queues stopped limiting the upload side on all the boards I upgraded to 6.0, Download limit works fine.?

Tue May 21, 2013 10:23 am

My Simple queues stopped limiting the upload side on all the boards I upgraded to 6.0, Download limit works fine.?

post your queue config. how did you check that they are not limiting? which version did you have before upgrade?

Arnold2222 · Tue May 21, 2013 10:29 am

You mean 6RC15.... for 6.0 it has too many issues

on RB 450G it miss like 4 packages which made my RB unreachable.

I made that firmware "downgrade" on RB 750 works fine
what packages are missing? when you upgrade, you must upload the packages you need, if you didn't upload them, they will not be installed.

Lets follow this issue in this topic
http://forum.mikrotik.com/viewtopic.php?f=19&t=72860

Chrisdewit · Tue May 21, 2013 10:31 am

They were all between 5.18-5.25. All are either 433ah boards or 435G. MY x86 system running ros v.6rc11 also works fine. Its only the 5 or 6 boards I upgraded last night to 6.0 that does this. Check the file attachment, its not showing any upload traffic. all 0

Chrisdewit · Tue May 21, 2013 10:40 am

Nevermind i've found the problem, its the "everyone" queue at the bottom, when i disable that the uplaod traffic starts running, was just a nice way to check the traffic going out of the board :/

oriondotnet · Tue May 21, 2013 10:41 am

Address List is not working on CCR

chain=forward action=drop dst-address=10.10.10.10 src-address-list=!ORION
in-interface=sfp1

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
uptime: 17h28m7s
version: 6.0
build-time: May/17/2013 14:04:20
free-memory: 3642.6MiB
total-memory: 3969.0MiB
cpu: tilegx
cpu-count: 36
cpu-frequency: 1200MHz
cpu-load: 0%
free-hdd-space: 905.5MiB
total-hdd-space: 1024.0MiB
architecture-name: tile
board-name: CCR1036-12G-4S
platform: MikroTik

Tue May 21, 2013 10:47 am

To Chrisdewit:

My guess is you have queue Nr:29 (named "everyone") as parent to all other simple queues.
Am I correct?

To fix your queues change target from 0.0.0.0/0 to 10.5.1.0/24 or specify target as interface name where clients are connected, everything should work normally

Now, lets think - can all the traffic (from and to your clients) can be considered as download from 0.0.0.0/0 ??? Yes, it can!
so nothing is left as upload.

lunchboxrts · Tue May 21, 2013 11:03 am

CCR LCD interface list missing names

DjM · Tue May 21, 2013 11:36 am

Hello MikroTik team,

is the issue with setting script variable via SMS solved, please?

Ticket#2013010766000731, opened in 01/2013.

Thank you

Chupaka · Tue May 21, 2013 11:43 am

*) console - fixed crash when variable name was not specified for

for... what?..

tinka · Tue May 21, 2013 11:50 am

I have upgraded a RB750G and RB2011UAS-2HnD to RouterOS 6.0. I have upgraded the firmware as well to 3.07 (RB750G) and 3.08 (RB2011).

In the upgrade procedure the RB2011 lost it's ip adress. After setting that correctly i can't reach it over it's ip adress either by winbox or web interface.

What is happening ?

(the rb750g works fine)

----

I cleared the configuration and entered the settings again and all is well. At this side however something went wrong with the ip adress.

janisk · Tue May 21, 2013 1:12 pm

*) console - fixed crash when variable name was not specified for
for... what?..

erm..

*) console - fixed crash when variable name was not specified for ':global', ':local', ':set', ':for' and ':foreach' commands;

Shkrid · Tue May 21, 2013 2:51 pm

My Simple queues stopped limiting the upload side on all the boards I upgraded to 6.0, Download limit works fine.?

+1
Simple queues stopped limiting the upload side on the hotspot bridge interface.
CCR1036-12G-4S

Address List is not working on CCR

works fine

Tue May 21, 2013 2:52 pm

My Simple queues stopped limiting the upload side on all the boards I upgraded to 6.0, Download limit works fine.?
+1
Simple queues stopped limiting the upload side on the hotspot bridge interface.
CCR1036-12G-4S

your configuration is probably wrong, check above solution by macgaiver

Shkrid · Tue May 21, 2013 3:05 pm

Only dynamic simple queue

/queue simple print detail 
 8  D name="hs-<HTTP_Auth_IT1>" target=br191 parent=none packet-marks="" priority=8/8 queue=hotspot-default/hotspot-default 
      limit-at=10M/10M max-limit=10M/10M burst-limit=0/0 burst-threshold=0/0 burst-time=0s/0s 

/interface bridge print      
 0  R name="br191" mtu=1500 l2mtu=65535 arp=enabled mac-address=XX:XX:XX:XX:XX:XX protocol-mode=rstp priority=0x8000 auto-mac=yes 
      admin-mac=00:00:00:00:00:00 max-message-age=20s forward-delay=15s transmit-hold-count=6 ageing-time=5m 

/ip hotspot print detail 
 0 S name="HTTP_Auth_IT1" interface=br191 profile=Free_10MB idle-timeout=none 
     keepalive-timeout=none ip-of-dns-name=10.0.0.2 proxy-status="running

/ip hotspot profile print detail
 3   name="Free_10MB" hotspot-address=10.0.0.2 dns-name="xxx.xx" 
     html-directory=Free rate-limit="10M" http-proxy=0.0.0.0:0 
     smtp-server=0.0.0.0 login-by=https,http-pap ssl-certificate=cert1 
     split-user-domain=no use-radius=no

Tue May 21, 2013 3:09 pm

Do you use bridge and "use-ip-firewall" in bridge settings?

Try to disable it and check if it works.

Shkrid · Tue May 21, 2013 3:14 pm

Yes, it works when "use-ip-firewall" disabled.

How to make that work simultaneously?

Tue May 21, 2013 3:25 pm

Avoid using simple queues with interface names as "target" and "dst." instead use ip addresses in those options.

onnoossendrijver · Tue May 21, 2013 3:26 pm

No directly related to 6.0, but will there be a RouterBoot upgrade for the RB600A, with support for partitioning?

Tue May 21, 2013 3:56 pm

No directly related to 6.0, but will there be a RouterBoot upgrade for the RB600A, with support for partitioning?

RB600 nand is 64mb

Minimum partition sizes:
32MB on MIPS
40MB on PowerPC
48MB on CCR

There is not enough space for two partitions on RB600

willbur · Tue May 21, 2013 4:39 pm

I didn't think that 6.0 was out of RC yet.... perhaps MK is pushing it out too early?

Attila · Tue May 21, 2013 5:52 pm

Dear Normis!

Multicast routing (PIM-SM) same source to different interface still doesn't work in CCR1036.
Same ROS version and same configuration (1. RP, 3. Interface) work like a charm in RB2011.

Please check out the problem.

Attila

Moc · Tue May 21, 2013 6:01 pm

I didn't think that 6.0 was out of RC yet.... perhaps MK is pushing it out too early?

You get to a point where the user based of a RC have tested all they had to test... And it normal that issues are popingup after an RC since the user base who try it going to be very large with lot of particular setup. As with any upgrade between major releases like this, it always good to test in a lab environment before putting in production, so it will allow them to fix the issues that wasn't reported or confirmed in the RC for the user who have specific usages.

savage · Tue May 21, 2013 6:27 pm

perhaps MK is pushing it out too early?

+1 But then again - MT is pretty much known for this behaviour... Just the recent issues I saw in RC14 (not even talking about this growing list)... I'm definately waiting before taking 6.0 anywhere near production.

ryan3531 · Tue May 21, 2013 7:21 pm

I just upgraded from 6.0rc14 to 6.0 final and found that IPv6 conntrack is not working. None of the rules appear to create state (in the Connections tab in Winbox) and reply packets all hit my default drop rules at the end of each chain, instead of the "accept established/related" rules. This is only happening with the IPv6 firewall; IPv4 conntrack appears to work as it should. I opened a ticket (#2013052166000812) about this and attached a supout file.

jozwiak · Tue May 21, 2013 8:34 pm

Problem with IPsec Peer and "Generate policy" Not working.
Downgraded til v6rc13 and it worked again

address=0.0.0.0/0 passive=no port=500 auth-method=pre-shared-key
secret="password" generate-policy=port-override
exchange-mode=main send-initial-contact=yes nat-traversal=no
my-id-user-fqdn="GroupVPN" proposal-check=obey hash-algorithm=sha1
enc-algorithm=3des dh-group=modp1024 lifetime=1d lifebytes=0
dpd-interval=disable-dpd dpd-maximum-failures=3

flynaj · Tue May 21, 2013 9:32 pm

RB751G-2HnD 5.25 Support USB wireless network card(ATHEROS 9271)
But 6.0 does not support,Why?

cheeze · Tue May 21, 2013 9:34 pm

Something I noticed about upgrading to 6.0 on x86. It kills all of the queues in queue tree. Once I rebuilt the queues everything else works.

Awesome, thank you Mikrotik

elmer · Tue May 21, 2013 10:06 pm

Dynamic WDS after reconnect station WDS creates new, no replacement free# of them.
Routerboard upgrade won`t work on all RB from winbox, only terminal.
Wireless works super! Good work MT team!

promind · Tue May 21, 2013 10:34 pm

Hello MikroTik,
Is VLAN working on 6.0 when enabled on x86 Intel PCI-X interface?
It's not working since first 6.x betas were released.

lcm · Tue May 21, 2013 10:37 pm

fresh x86 install on virtualbox:

i did a "system reset-configuration", on next boot i got a "no such file or directory" error, image attached.

virtual box related ?

wulfgard · Tue May 21, 2013 10:56 pm

Hello all

as we can see v6.0 on CCR1036 works fine and smooth in production environment with

- L2MTU 9000
- OSPF
- BGP
- MPLS LDP
- VPLS BGP MTU 1500
- TE TUNNELS

max packet : 300000 per vpls which mean about 170 Mbps duplex for 64 byte and full 1Gbps duplex with 512 bytes at minimum

all setup from scratch to avoid migration issues

a+
Thierry

timoid · Tue May 21, 2013 11:55 pm

Hello MikroTik,
Is VLAN working on 6.0 when enabled on x86 Intel PCI-X interface?
It's not working since first 6.x betas were released.

I've tested and VLANs do not appear to work in 6.0 on x86.

Chupaka · Wed May 22, 2013 12:34 am

Something I noticed about upgrading to 6.0 on x86. It kills all of the queues in queue tree. Once I rebuilt the queues everything else works.

kills? or just binds to 'unknown' interface instead of 'global-something'? isn't it because there's no 'global-something' in v6 and there's no 'global' in previous versions?

onnoossendrijver · Wed May 22, 2013 12:51 am

Hello MikroTik,
Is VLAN working on 6.0 when enabled on x86 Intel PCI-X interface?
It's not working since first 6.x betas were released.
I've tested and VLANs do not appear to work in 6.0 on x86.

I use an Intel DN2800MT board (has Intel NIC onboard). VLANs are working fine.

InoX · Wed May 22, 2013 1:19 am

SXT lite 5 hang if system/reboot
power cycle needed or watchdog

mark · Wed May 22, 2013 2:19 am

The first SXT Lite 2 I've grabbed and updated from v6rc14 rebooted over and over again for about half an hour several times. After unplugging its power source entirely it rebooted five times. And yes, I've tried another cable (it didn't make any difference).

yogii · Wed May 22, 2013 6:31 am

ROS 6.0 export, print double dir /int pppoe-client.

normal in 6.0rc14.

thank you.

timberwolf · Wed May 22, 2013 8:02 am

I'm running a testing setup with OSPF and BGP all over L2TP, with 5.25 no problems.
With 6.0 OSPF is behaving quite strange with messages like

may/21 20:27:24 route,ospf,info OSPFv2 neighbor 10.42.1.104: state change from ExStart to 2-Way
may/21 20:28:05 route,ospf,info OSPFv2 neighbor 10.42.1.104: state change from ExStart to 2-Way
may/21 20:29:08 route,ospf,info OSPFv2 neighbor 10.42.1.104: state change from Exchange to 2-Way
may/21 20:29:08 route,ospf,info OSPFv2 neighbor 10.42.1.104: state change from 2-Way to Down

in the logs. I also got a crash on the central router of the setup...

But hey, thats what we are used to with new major releases

I can't recommend using 6.0 in production as long as there are issues with OSPF.

Wed May 22, 2013 8:19 am

Hello MikroTik,
Is VLAN working on 6.0 when enabled on x86 Intel PCI-X interface?
It's not working since first 6.x betas were released.
I've tested and VLANs do not appear to work in 6.0 on x86.

promind and timoid,
Could you please send supout.rif files to support@mikrotik.com for research?

timberwolf · Wed May 22, 2013 8:59 am

NTP Client status isn't reflected in Winbox, always shows stopped although CLI states synchronized, 6.0 on x86

themenace · Wed May 22, 2013 9:47 am

Upgraded one of my test RB2011's before rollout to customers V6.0 FW 3.08, noticed that it started to drop occasional ping (on LAN) (monitored by dude)
Can see one of the eth interfaces going up and down exactly on the hour (15th minute) in the log
Was previously on 5.25 - no issue

Muqatil · Wed May 22, 2013 10:30 am

I'm brave:
V6.0 on CCR1036 running on core router on top of BGP/OSPF, Queue Tree, Firewall. Everything's working since upgrade.

themenace · Wed May 22, 2013 10:50 am

Update : Since reverting to 5.25 / 3.07, eth does not drop every 1 hour (on the 15th minute)
Ping does not drop occasional packet

Ansy · Wed May 22, 2013 11:14 am

Please check, from where it picks garbage addresses into Torch when started from Simple Queues?

tkgit · Wed May 22, 2013 12:04 pm

751u2hnd-ROS6-fw.jpg

why?

maxstel · Wed May 22, 2013 12:08 pm

Sorry guys,
what exactly does it mean this message?

Wed May 22, 2013 12:24 pm

Sorry guys,
what exactly does it mean this message?

Don't enter Scan-list with commas. Use the "down arrow" to add more fields. As an alternative, you can make a channel list in the "Channels" section, then use the channel list name in this field.

maxstel · Wed May 22, 2013 12:31 pm

Sorry guys,
what exactly does it mean this message?
Don't enter Scan-list with commas. Use the "down arrow" to add more fields. As an alternative, you can make a channel list in the "Channels" section, then use the channel list name in this field.

Understood! Thanks as always, Normis. Sorry to bother you with such "problems"...

greek · Wed May 22, 2013 3:38 pm

Upgrade RB1100AHx2 from 5.25 to 6.0

I see broblem with Bridge between vlan interface and physical interfaces. Arp - ok, dhcp -ok, ping ip on bridge int - Ok, ping thru bridge - NOT Ok.

Downgrade to 5.25 is solving problem. I was testing it 2 times.

More detail try to post in 2-3 days.

samsung172 · Wed May 22, 2013 6:16 pm

6.0 on CCR and X86 (only one tested) still have the vrf issue. ITs 100% CPU, and not even possible to do a /export or supout from the boxes. Is there any solution to the vrf issue, that have been in almost all 6.x versions. ITs impossible to use vrf on CCR, and that is a REALLY bad thing.

cheeze · Wed May 22, 2013 7:42 pm

I think I may have found a bug on x86 version of 6.0.

I believe that loopback interfaces (or in this case, a bridge without anything on it) might end up being broken when it comes to adding it within OSPFv3. On my MIPS-BE router (RB751) it works perfectly, but on my x86 router it shows as inactive and down.

Here's my MIPS-BE box:

[<redacted>@STUFF-NETWORK-WAP] /routing ospf-v3 interface> print
Flags: X - disabled, I - inactive, D - dynamic, P - passive
 #    INTERFACE                                                                                                      AREA                                                                                                      COST PRIORITY NETWORK-TYPE 
 0    Ethernet 1/POE                                                                                                 0.0.0.0                                                                                                     20        0 default      
 1  P Loopback 0                                                                                                     0.0.0.0                                                                                                      1        0 default      
 2  P Switching Bridge                                                                                               0.0.0.0                                                                                                      1        0 default

Here's my x86 box:

[<redacted>@STUFF-NETWORK-EDGE] /routing ospf-v3 interface> print
Flags: X - disabled, I - inactive, D - dynamic, P - passive
 #    INTERFACE                                                                                                      AREA                                                                                                      COST PRIORITY NETWORK-TYPE 
 0    BUILT IN ETHERNET                                                                                              0.0.0.0                                                                                                     20        0 default      
 1 IP Loopback 0                                                                                                     0.0.0.0                                                                                                      1        0 default

Both are configured identically. However on the x86 box it shows inactive and down. I've restarted the box, reconfigured the IP addresses, restarted the OSPFv3 process and area commands, disabled/enabled the loopback interface and still no go. On the MIPS-BE box it works perfectly. I have sent an email to support@mikrotik.com with the title of "OSPFv3 does not recognize loopback on x86, but it works in MIPS-BE‏" and the corresponding configs/screenshots/supout.rif files. Ticket is 2013052266001006.

Has anyone else experienced this?

Something I noticed about upgrading to 6.0 on x86. It kills all of the queues in queue tree. Once I rebuilt the queues everything else works.
kills? or just binds to 'unknown' interface instead of 'global-something'? isn't it because there's no 'global-something' in v6 and there's no 'global' in previous versions?

Chupaka, I think you're right. I think this is what's actually going on. However when I upgraded my MIPS-BE board, it actually kept everything on queues. Nothing too bad I guess, it's just something I noticed.

wildbill442 · Wed May 22, 2013 8:17 pm

Just to confirm...

I've tested Queue Trees / Address lists / PPPoE Server

They all seem to be working fine.

I did a fresh install on a CCR-1036-12G-4S of ROS6.0 and restored a backup file from my production RB1100AHx2 running 5.25.

I did have to make some changes to the packet markings, queue trees, interface/IP bindings, etc.. Due to the change in ROS version and hardware. Also the packet markings had to be rearranged I believe due to the change in Queue Tree structure in ROS6. I was previously marking Download traffic in the Forward chain, I had to move to the Postrouting chain for it to mark and Queue appropriately. Also due to the lack of the old "Global-Type" queues I had to edit the Queue trees for the new "Golbal" queue.

I haven't tested the OSPF features, but others seem to have already confirmed these to be working properly.

This all seemed pretty straight forward to me. There's been some structural changes to RouterOS in v6, so as you should always do, test first before upgrading a production device.

Talyon · Wed May 22, 2013 9:08 pm

Don't know if anyone else ran into this. I'm on a RB751U-2HnD and the default configuration script does not seem to be present in v6.0
I'm probably way under everyone else's skill level, i had to get into google to get the information below.
So the fact that it's not correctly setting up from scratch really had me in a bind.

[admin@MikroTik] > /system default-configuration print
script:
[admin@MikroTik] >

turm · Wed May 22, 2013 9:53 pm

Today I upgraded my new RB2011UAS-IN to V.6 Then I wanted to build a hotspot. WAN IP was connected and works fine.
I did the setup with the winbox /ip-Hotspot-Servers-Hotspot Setup.
But when i connected a PC to the Hotspot Port, there was no redirectin to the login page. The Computer gets a normal Adress through DHCP.
Then i discovered, that the setup no longer provides the HTML-Files for the Redirection.
Well, I recovered the files from another RB2011 with V5.25. But the redirection still does not work. There seems to be some renaming of the HTML Files inside V.6.

Is that a normal behaviour?

hedele · Wed May 22, 2013 9:56 pm

I think I may have found a bug on x86 version of 6.0.

I believe that loopback interfaces (or in this case, a bridge without anything on it) might end up being broken when it comes to adding it within OSPFv3. On my MIPS-BE router (RB751) it works perfectly, but on my x86 router it shows as inactive and down.

You need to give your bridge interface an admin-mac-address. It will work fine in OSPFv3 afterwards!
Caveat: It may not work on first try, if it doesn't, assign a different admin-mac-address. You only have to do that once.

cheeze · Wed May 22, 2013 10:03 pm

I think I may have found a bug on x86 version of 6.0.

I believe that loopback interfaces (or in this case, a bridge without anything on it) might end up being broken when it comes to adding it within OSPFv3. On my MIPS-BE router (RB751) it works perfectly, but on my x86 router it shows as inactive and down.
You need to give your bridge interface an admin-mac-address. It will work fine in OSPFv3 afterwards!
Caveat: It may not work on first try, if it doesn't, assign a different admin-mac-address. You only have to do that once.

Ho...leee....shiteth...

You sir/ma'am are absolutely spot on. I did not know RouterOS requires this. Holy crap I'm an idiot

Thank you thank you...

Seems my Cisco then saw this change in the routing table:

STUFF-NETWORK-CORE#
28w0d: IPv6RT[Default]: ospf 1, Reuse backup for FDFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:0/126, distance 110
28w0d: IPv6RT[Default]: ospf 1, Reuse backup for FDFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:8/126, distance 110
28w0d: IPv6RT[Default]: ospf 1, Route add FDFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFB/128 [new 110/21]
28w0d: IPv6RT[Default]: ospf 1, Added path FE80::230:1BFF:FEBE:EB41/GigabitEthernet1/0/1
28w0d: IPv6RT[Default]: ospf 1, Route add FDFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFC/128 [owner]
28w0d: IPv6RT[Default]: ospf 1, Route add FDFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FF20/124 [owner]
28w0d: IPv6RT[Default]: Event: FDFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFB/128, Add, owner ospf, previous None

There we go. We're all good

mdminfo · Wed May 22, 2013 11:11 pm

Proxy is not working

---

cbrown · Thu May 23, 2013 2:02 am

Today I upgraded my new RB2011UAS-IN to V.6 Then I wanted to build a hotspot. WAN IP was connected and works fine.
I did the setup with the winbox /ip-Hotspot-Servers-Hotspot Setup.
But when i connected a PC to the Hotspot Port, there was no redirectin to the login page. The Computer gets a normal Adress through DHCP.
Then i discovered, that the setup no longer provides the HTML-Files for the Redirection.
Well, I recovered the files from another RB2011 with V5.25. But the redirection still does not work. There seems to be some renaming of the HTML Files inside V.6.

Is that a normal behaviour?

Hotspot is not working for me either.

sniggle · Thu May 23, 2013 5:26 am

Hey all,

Upgraded to 6.0 from 5.17 without a hitch so far, however the System/Routerboard section of WebFig is all blank now. From what I recall, I was running firmware 2.36 and 2.39 was available but I never bothered to install it. Now I can't see the serial number or anything. If I go into the settings of that section, the dropdown boxes for boot device, CPU freq, etc are all empty. I'm running an RB450G. Any ideas?

Edit for just a couple more details:

The System/Health section is also completely empty, however the System/Resources section properly shows all data. Not sure if this helps. Thanks!

RESOLVED: It was the stylesheets of WebFig v5.17 being cached by my browser, thus not rendering things fully correctly in v6.0. Unsure if the WebFig HTTP server was reporting a 304 on those documents or not, but that could be a slight bug.

Thu May 23, 2013 8:10 am

Today I upgraded my new RB2011UAS-IN to V.6 Then I wanted to build a hotspot. WAN IP was connected and works fine.
I did the setup with the winbox /ip-Hotspot-Servers-Hotspot Setup.
But when i connected a PC to the Hotspot Port, there was no redirectin to the login page. The Computer gets a normal Adress through DHCP.
Then i discovered, that the setup no longer provides the HTML-Files for the Redirection.
Well, I recovered the files from another RB2011 with V5.25. But the redirection still does not work. There seems to be some renaming of the HTML Files inside V.6.

Is that a normal behaviour?
Hotspot is not working for me either.

Do you, or have you in the past, used any type of branding package on this device? We have seen a few complaints, but are unable to reproduce it on any router. We tried many times.

djras · Thu May 23, 2013 8:47 am

Problem with a Graphing of system resources RB-2011LS again.

Thu May 23, 2013 8:52 am

Problem with a Graphing of system resources RB-2011LS again.

what do you have set in the "resource rules" tab?

Thu May 23, 2013 9:17 am

Hotspot is not working for me either.
Do you, or have you in the past, used any type of branding package on this device? We have seen a few complaints, but are unable to reproduce it on any router. We tried many times.

We managed to get remote access to one such device. Problem is fixed in v6.1

djras · Thu May 23, 2013 9:22 am

what do you have set in the "resource rules" tab?

0.0.0.0/0 yes
I tried to write one IP also.

ROS v5.25 type is CPU HDD Memory - Ok.
ROS v6.0rc14 v6.0 type is unknown!
Also I updated firmware 3.07 3.08. The problem repeats.

vik1988 · Thu May 23, 2013 10:06 am

Timberwolf is right.....

OSPF issue is happening with us also...... getting flapped automatically. Downgraded to ROS 5.24...

elmer · Thu May 23, 2013 12:52 pm

After system / reset with one wlan card i have off course

one wlan1 interface.
When i plugged another card i have another wlan1... ALIX 1D with RB14 card, license LVL5.

Rudios · Thu May 23, 2013 12:59 pm

what do you have set in the "resource rules" tab?
0.0.0.0/0 yes
I tried to write one IP also.

ROS v5.25 type is CPU HDD Memory - Ok.
ROS v6.0rc14 v6.0 type is unknown!
Also I updated firmware 3.07 3.08. The problem repeats.

I experience the same problem, but only on 1 of the two RB2011's I have.

Thu May 23, 2013 1:03 pm

what do you have set in the "resource rules" tab?
0.0.0.0/0 yes
I tried to write one IP also.

ROS v5.25 type is CPU HDD Memory - Ok.
ROS v6.0rc14 v6.0 type is unknown!
Also I updated firmware 3.07 3.08. The problem repeats.
I experience the same problem, but only on 1 of the two RB2011's I have.

can any of you provide remote access to your device? contact support@Mikrotik.com about ths

Rudios · Thu May 23, 2013 2:42 pm

can any of you provide remote access to your device? contact support@Mikrotik.com about ths

I've send a mail. What kind of access do you need?

Thu May 23, 2013 2:45 pm

can any of you provide remote access to your device? contact support@Mikrotik.com about ths
I've send a mail. What kind of access do you need?

full SSH access would be the best. also winbox and web, so we can see the problem. simply make a new user for support, which is in the "full" group. then disable firewall on the internet port, and send us your public IP

turm · Thu May 23, 2013 2:47 pm

Hotspot is not working for me either.
Do you, or have you in the past, used any type of branding package on this device? We have seen a few complaints, but are unable to reproduce it on any router. We tried many times.
We managed to get remote access to one such device. Problem is fixed in v6.1

I have no rebranding - I bought the Routerboard at Meconet in Germany

But if you wish I can set up an access for you, with a fresh Installation (only WAN is provided)

Thu May 23, 2013 2:52 pm

turm, like I already said, problem is fixed. you can try pre-release build here:
http://www.mikrotik.com/download/share/ ... 6.1rc1.npk

Davis · Thu May 23, 2013 3:01 pm

Thanks MikroTik for wonderful hardware and software! And congratulations with release!

I want to report a bug with IPSec.
After upgrading from 5.25 to 6.0 IPSec VPN (IP over IP tunnel via IPSec in transport mode) stopped to work.
A lot was logged (when enabled ipsec logging), incloding the following:

14:36:40 ipsec,debug fatal INVALID-PAYLOAD-TYPE notify messsage, phase1 should be deleted.

Solution was to enable default IPSec proposal (which isn't used and was disabled).

JonasJ · Thu May 23, 2013 6:01 pm

To avoid any migration issues after update of my RB493AGH, I did clean install via Netinstall, manually configured RB for required configuration.

Jono_MikroTik_6-0_before-reboot.jpg

Works fine, until reboot...

After reboot, external WAN interface is not presented in ARP list table, no ping from LAN to WAN.

DHCP client is still alive and is getting external IP.

Jono_MikroTik_6-0_after-reboot.jpg

Doing Restore from fresh Config file, and again - works fine, but until next reboot...

Switched back to my lovely 5.25

Any ideas?

garlicbulb · Thu May 23, 2013 10:15 pm

Installed 6.0 on RB-750. When to System -> Reset Configuration and reset with "No Default Configuration" not checked. Box came up with no configuration present.

Loaded in a configuration backup from a V5 system and did "Restore". Box died. No link lights whatsoever.

Did a reset using the reset button. Wound up with no configuration present.

Deac · Thu May 23, 2013 10:47 pm

Bonding with ARP monitoring is not working, disable ARP monitoring or change to MII solve the problem, tested on 750g, 750gl, 1000AH and 1100AHx2

Agree for RB433UAHL also.
While you're working to fix it, bonding code can be temporarily backported from v5.25?
If it's possible.

In my test lab I see a great improvement in the wireless code. Especially for nstreme mode. Great work!

biasottocarvalho · Thu May 23, 2013 10:56 pm

Could someone provide me rc14 for CCR1016-12g?

Stillhard · Thu May 23, 2013 11:16 pm

Tested 6.1rc1 (05/22/2013) still error in usermanager web-ui (web-ui ignoring timezone setting) - but no problem in cli (/tool user-manager session print)

honzam · Fri May 24, 2013 12:04 am

Hello MT team.
Do you want make an official bug tracker list?

Something like this?
http://bugs.mikrotik-routeros.com/view_all_bug_page.php
Thanks

bryans2k · Fri May 24, 2013 1:00 am

Hi,

CCR1036-12G-4S running GA v6.0

1. I have two static default routes setup.
2. I have a dst-nat setup.
3. I have a netwatch setup to monitor the primary default route.
4. Whenever I reboot the router the netwatch script fails to execute fully when it’s written like it is below. In fact it confuses route ID 0 for route ID 1 as well at times.
5. Whenever I re-wrote it to enable and disable via set [find comment=”Default Route”] disabled=yes the script works as it should.

Down:
:if ([/ping 10.0.0.1 count=2] = 0) do={
/ip firewall nat set enable 0;
/ip route disable 0;
/tool e-mail send to="person@email.com" subject="Gateway Down" body="Pinged out.";
}

Up:
:if ([/ping 10.0.0.1 count=2] = 2) do={
/ip firewall nat set disable 0;
/ip route enable 0;
/tool e-mail send to="person@email.com" subject="Gateway Up" body="Pinged in.";
}

BETEPAH · Fri May 24, 2013 7:24 am

Router OS on x86 server hardware
6.0rc11 has lot drops on interfaces
6.0rc13 no drops
6.0 have lot drops again

Без имени-1.png

negge · Fri May 24, 2013 9:01 am

I noticed that if the multicast package is installed but the routing package isn't, the Routing menu in Winbox does not have an icon. In fact I'm not sure that installing the routing package fixes it but I suspect it does.

Otherwise everything is fine, glad to see that the queue lockup issue has been fixed!

majkel · Fri May 24, 2013 11:09 am

on 1036 there is no RX Drops.. I have 4 days uptime.

stafross · Fri May 24, 2013 1:18 pm

I have upgraded 2 X Omnitik UPA-5HnD from 6rc14 with Firmware 3.07 to 6.0, all packages were enabled. I then disabled the Hotspot, IPv6 and MPLS packages and rebooted. The routers never came back up again.

Have been trying to do netinstalls on them but it only gets to partition and format and nothing else happens.

Any sugestions?

Stillhard · Fri May 24, 2013 1:32 pm

Tested 6.1rc1 (05/23/2013)
- still error in usermanager web-ui (web-ui ignoring timezone setting) - but no problem in cli (/tool user-manager session print)
- new error, the api service is not functioning

Fri May 24, 2013 1:34 pm

Tested 6.1rc1 (05/23/2013)
- still error in usermanager web-ui (web-ui ignoring timezone setting) - but no problem in cli (/tool user-manager session print)
- new error, the api service is not functioning

re-download. May 24 build solves API problem

Fri May 24, 2013 1:46 pm

Is anyone else experiencing DHCP server not working on v6 x86 ?

Fri May 24, 2013 1:47 pm

Is anyone else experiencing DHCP server not working on v6 x86 ?

run sniffer files from clients and send to support. we have not yet had any reports.

ok2slc · Fri May 24, 2013 2:39 pm

I have a problem with PPP package on RB1000. After some time (about next a day after reboot, tested 2x) I don´t read via Winbox no parameter (PPPoE servers, Secrets, etc.) in PPP besides dynamic Interface. Attempt to remove this interfaces ends timeout. PPP does not even read over New Terminal and API (API for firewall working normally). V6rc14 working fine.

EDIT: In v6rc14 the same problem now

.

Sorry, my English is not good

morf · Fri May 24, 2013 3:03 pm

I've updated the ROS 5.18 x86 -> 6.0 x86
Everything worked, except vlan. Enables / disables the vlan interfaces, nothing helped. Rolled back to 5.18

Stillhard · Fri May 24, 2013 3:05 pm

Tested 6.1rc1 (05/23/2013)
- still error in usermanager web-ui (web-ui ignoring timezone setting) - but no problem in cli (/tool user-manager session print)
- new error, the api service is not functioning
re-download. May 24 build solves API problem

OK tested 6.1rc1 (05/24/2013)
- NOT FIXED, still error in usermanager web-ui (web-ui ignoring timezone setting) - but no problem in cli (/tool user-manager session print)
- FIXED, the api service is not functioning

giopao · Fri May 24, 2013 3:16 pm

Upgrade RB193 from 5.25 to 6.0
not working; wilreless is ok, traffic on ethernet is limited to 500kb/s

Upgrade RB951-2n grom 5.25 to 6.0, seems ok

both downgraded to 5.25

I'll wait next release for other upgrade.

stafross · Fri May 24, 2013 4:16 pm

I have upgraded 2 X Omnitik UPA-5HnD from 6rc14 with Firmware 3.07 to 6.0, all packages were enabled. I then disabled the Hotspot, IPv6 and MPLS packages and rebooted. The routers never came back up again.

Have been trying to do netinstalls on them but it only gets to partition and format and nothing else happens.

Any sugestions?

Because the Omnitik does not have a serial port I am at a loss of what to do to recover these devices and am also not inclined to reboot any more of my devices upgraded to 6.0 as they might also stop working.

Any help from MT or anyone out there will be greatly appreciated.

Fri May 24, 2013 4:20 pm

I have upgraded 2 X Omnitik UPA-5HnD from 6rc14 with Firmware 3.07 to 6.0, all packages were enabled. I then disabled the Hotspot, IPv6 and MPLS packages and rebooted. The routers never came back up again.

Have been trying to do netinstalls on them but it only gets to partition and format and nothing else happens.

Any sugestions?
Because the Omnitik does not have a serial port I am at a loss of what to do to recover these devices and am also not inclined to reboot any more of my devices upgraded to 6.0 as they might also stop working.

Any help from MT or anyone out there will be greatly appreciated.

Follow the instructions in this document to reset, or to reinstall the device: http://i.mt.lv/routerboard/files/OmniTi ... nD-qg2.pdf

JonasJ · Fri May 24, 2013 5:15 pm

I've updated the ROS 5.18 x86 -> 6.0 x86
Everything worked, except vlan. Enables / disables the vlan interfaces, nothing helped. Rolled back to 5.18

The 493G RB of mine has also vlan, EoIP interfaces (see post above), and might be either vlan, or EoIP interface is still unstabte with 6.0, or combination of them

As far as I remember, EoIP was unstable in 6.xx rc?

I also rolled back to 5.25, and again, works exclusively fine and stable with this version.

timberwolf · Fri May 24, 2013 5:53 pm

Timberwolf is right.....

OSPF issue is happening with us also...... getting flapped automatically. Downgraded to ROS 5.24...

I couldn't narrow down the cause by now, but it seem to be caused by short lineflaps or packet loss. So be carefull on unstable links.
I am guessing that its either an error in the state maschine or the associated timers.

tiggda · Fri May 24, 2013 6:27 pm

Seeing v.6 at last is a nice thing, but it seems it was released too early. Anyone else suffering from "/system backup save" issues? The thing is that I had problems with earlier versions of RouterOS (v.5.2x) - it created broken backup files, which could not be restored. The behavior has changed in v.6 - now the backup starts and writes constantly to the nand until it is filled up to 100%. Output as follows:

/system backup save                      
Saving system configuration
Failed to save system configuration backup
action timed out - try again, if error continues contact MikroTik support and send a supout file (13)

I would appreciate any hints on how to solve this.

Thanks,
Lukasz

yogii · Fri May 24, 2013 6:56 pm

Seeing v.6 at last is a nice thing, but it seems it was released too early. Anyone else suffering from "/system backup save" issues? The thing is that I had problems with earlier versions of RouterOS (v.5.2x) - it created broken backup files, which could not be restored. The behavior has changed in v.6 - now the backup starts and writes constantly to the nand until it is filled up to 100%. Output as follows:
Code: Select all
/system backup save                      
Saving system configuration
Failed to save system configuration backup
action timed out - try again, if error continues contact MikroTik support and send a supout file (13)
I would appreciate any hints on how to solve this.

Thanks,
Lukasz

what type of routerboard you have tested?

it works fine for my RBSXT-5HnD for backup save and load.

tiggda · Fri May 24, 2013 9:19 pm

Seeing v.6 at last is a nice thing, but it seems it was released too early. Anyone else suffering from "/system backup save" issues? The thing is that I had problems with earlier versions of RouterOS (v.5.2x) - it created broken backup files, which could not be restored. The behavior has changed in v.6 - now the backup starts and writes constantly to the nand until it is filled up to 100%. Output as follows:
Code: Select all
/system backup save                      
Saving system configuration
Failed to save system configuration backup
action timed out - try again, if error continues contact MikroTik support and send a supout file (13)
I would appreciate any hints on how to solve this.

Thanks,
Lukasz
what type of routerboard you have tested?

it works fine for my RBSXT-5HnD for backup save and load.

My problems started while I was still using RB450G, right now I have RB2011UAS-2HnD-IN configured in the same way as on RB450G and the problem is still there.

Thanks,
Lukasz

stafross · Fri May 24, 2013 9:23 pm

I have upgraded 2 X Omnitik UPA-5HnD from 6rc14 with Firmware 3.07 to 6.0, all packages were enabled. I then disabled the Hotspot, IPv6 and MPLS packages and rebooted. The routers never came back up again.

Have been trying to do netinstalls on them but it only gets to partition and format and nothing else happens.

Any sugestions?
Because the Omnitik does not have a serial port I am at a loss of what to do to recover these devices and am also not inclined to reboot any more of my devices upgraded to 6.0 as they might also stop working.

Any help from MT or anyone out there will be greatly appreciated.
Follow the instructions in this document to reset, or to reinstall the device: http://i.mt.lv/routerboard/files/OmniTi ... nD-qg2.pdf

As stated above I have been trying to do a NETINSTALL but the process gets stuck on "Partitioning and Format." the install never starts.

HaPe · Fri May 24, 2013 11:15 pm

In 6.0, F5 (repaint syntax) in editor doesn't work. To do it, you need to close and open again editor.

incoming429 · Sat May 25, 2013 2:19 am

It would be great if the order of items in the left panel in WebFig was be the same as in Winbox (for example IPv6 in WebFig is now below Log).

Thank you

JorgeAmaral · Sat May 25, 2013 2:32 am

Does one-to-one nat in hotspot work for anyone?
I have been testing and it seems to fail in v6.

biasottocarvalho · Sat May 25, 2013 3:45 am

Could someone provide me rc14 for CCR1016-12g?

infused · Sat May 25, 2013 11:24 am

Could someone provide me rc14 for CCR1016-12g?

rc13 is more more stable.

Sat May 25, 2013 12:59 pm

*) ipsec - added /peer passive option which will prevent starting ISAKMP negotiation
and signifies xauth responder/initiator side;
*) ipsec - added pre-shared-key-xauth and rsa-signature-hybrid authentication methods;

GUI support for these features seems to be missing. GUI support for mode-cfg seems to be missing as well. When can we expect these options to be added to Winbox and Webfig?

yogii · Sat May 25, 2013 1:29 pm

Could someone provide me rc14 for CCR1016-12g?

here are the links.
http://download2.mikrotik.com/routeros/ ... .0rc14.zip
http://download2.mikrotik.com/routeros/ ... .0rc14.npk

just change number after "rc" to download minor version.

devilwolf90 · Sat May 25, 2013 1:42 pm

limit bytes out not working ............

estdata · Sat May 25, 2013 5:03 pm

I put the wireless-frequsage > kicked and then goes to the router off (disconnect)

this is big problems

wiltonlee · Sun May 26, 2013 3:23 am

After upgrading to v6 released, the logging time/date is defaulted to GMT although system clock is set to +8hrs from GMT.

Please help..

putinka · Sun May 26, 2013 12:38 pm

My system resource:

[admin@MikroTik] > system resource print                                                           
version: 6.0
build-time: May/17/2013 14:04:20
cpu: MIPS 74Kc V4.12
architecture-name: mipsbe
board-name: RB2011L

What happened to the item "yes"

:

[admin@MikroTik] > ip ipsec peer add generate-policy= 
no  port-override  port-strict

estdata · Sun May 26, 2013 2:12 pm

What is new 6.1RC1 ? i see this demo.mt.lv is coming new release

putinka · Sun May 26, 2013 2:17 pm

What happened to the item "yes" :
Code: Select all
[admin@MikroTik] > ip ipsec peer add generate-policy= 
no  port-override  port-strict

port-override == yes

aTan · Sun May 26, 2013 5:00 pm

I just upgraded from 6.0rc14 to 6.0 final and found that IPv6 conntrack is not working. None of the rules appear to create state (in the Connections tab in Winbox) and reply packets all hit my default drop rules at the end of each chain, instead of the "accept established/related" rules. This is only happening with the IPv6 firewall; IPv4 conntrack appears to work as it should. I opened a ticket (#2013052166000812) about this and attached a supout file.

I have the same problem. IPv6 conntrack doesn't work at all.

mark · Sun May 26, 2013 7:28 pm

I am growing increasingly wary of Microtik's IPv6 support due to:

»Bridge-local« doesn't properly get a link-local IPv6 address at boot time resulting in no »router advertisements« being sent to connected hosts, in turn resulting in their IPv6 connectivity loss.
Even after deleting a faulty address (faulty as in »assigned to interface ›unknown‹«) a link-local address isn't recreated.

Furthermore:

Several different devices, having MIPSBE architecture in common, power up in some sort of reboot-loop. They're becoming inaccessible for minutes, sometimes even hours or quasi-permanent!
»bridge-local« still disappears in v6.0 FW 3.08 (RB951G-2HnD — I've removed bridges on every other device therefore I won't rule out the issue exists there, too)

I didn't hear a word from Mikrotik about these issues being addressed.

bartjoo · Sun May 26, 2013 10:40 pm

After the installing my RB is rebooting everytime. He never came up.
with hard reset it doesnt work.. every time a reboot in 60seconds..
help me!

zamani · Mon May 27, 2013 4:04 am

Hello everyone.
I install routeros v6.0 on my RB911G. with winbox. but after reboot my router stop working,boot fail!
I can't access to it with winbox or....
no ip , mac address...
RB911G doesn't have reset button.how can I use netinstall?!
any other way?

simpl3x · Mon May 27, 2013 7:49 am

Hello everyone.
I install routeros v6.0 on my RB911G. with winbox. but after reboot my router stop working,boot fail!
I can't access to it with winbox or....
no ip , mac address...
RB911G doesn't have reset button.how can I use netinstall?!
any other way?

you can try use reset ring on board:

1.jpg

yogii · Mon May 27, 2013 8:16 am

RB911G doesn't have reset button.how can I use netinstall?!

button in the brown stripped box like in the picture below should be reset button.

bartjoo · Mon May 27, 2013 9:01 am

Hello, the reset button and jumper doesnt work for me.
How can i use netinstall? I dont have a com port
On the mikrotik 951g. And he reboots every time, so i dont have time to logon

update:
it works:)
http://www.mikrotik.com.my/reinstalling ... rial-port/

SoKaR · Mon May 27, 2013 2:53 pm

What is new 6.1RC1 ? i see this demo.mt.lv is coming new release

What's new in 6.1rc1 (2013-May-27 08:19):

*) api - added support for API over TLS (SSL);
*) api - api service is now enabled by default;
*) ppp - do not show R flag for locally authenticated users;
*) vrrp - fixed ah authentication;
*) webfig - added support for RADIUS authentication (via MS-CHAPv2);
*) ipsec - for peers with full IP address specified system will
autostart ISAKMP SA negotiation;
*) trafficgen - added inject-pcap command for replaying pcap files into network;
*) dns - retry queries with tcp if truncated results received;

cast · Mon May 27, 2013 3:28 pm

in RouterOS 5.xx
/tool email send tls=yes ...
in RouterOS 6.0
/tool email send start-tls=yes ...

WHY ???

Is there any other renamings?
how users can guess this things? only by non-working scripts?

Mon May 27, 2013 3:54 pm

here is a list of changes: http://wiki.mikrotik.com/wiki/Manual:What%27s_New_In_v6

elmer · Mon May 27, 2013 4:24 pm

My RB435G after firmware update and reboot is unaccessible on all protocol

Internet works for now, but dhcp-server not! Must go reboot via power...

Problem resolved, CPU settings gone to 100Mhz... Disable WLAN`s set to normal 680Mhz
then reboot and enable WLAN resolved problem

sealin · Mon May 27, 2013 4:49 pm

here is a list of changes: http://wiki.mikrotik.com/wiki/Manual:What%27s_New_In_v6

Hi,
I setup Ros5.25 & Ros6.0 in different Virtual PCs.
In each Ros, I add 1000 pppoe-client and 1000 routes.
I use scripts below:
As for pppoe-client
:for sheng from=1 to=1000 do={/int pppoe-client
add interface=ether1 name=("pppoe-out" . $sheng) password=1 user=1}
As for Routes
:for sheng from=1 to=1000 do={/ip route
add disabled=yes distance=1 dst-address=0.0.0.0/0 gateway=("pppoe-out" . $sheng) routing-mark=$sheng scope=30 target-scope=10}
At last, I find that either Ros5.25 or Ros6.0 could enable more than 252 routes. If routes do not show reachable or unreachable, they can not be used in mangle.Here are pictures and supout files.
So Is the number of routes limited?
Thanks a lot.
Have a nice day!^_^

Adolfo · Mon May 27, 2013 6:32 pm

fresh x86 install on virtualbox:

i did a "system reset-configuration", on next boot i got a "no such file or directory" error, image attached.

virtual box related ?

Same issue on a ccr1016, using two different downloads of npk file.

Stillhard · Mon May 27, 2013 7:04 pm

tested 6.1rc1 (05/24/2013) all the way to (05/272013)
- NOT FIXED, still error in usermanager web-ui (web-ui ignoring timezone setting) - but no problem in cli (/tool user-manager session print)
- NEW ERROR, ip > hotspot > active - Session Time Left empty

zamani · Mon May 27, 2013 7:21 pm

thanks simpl3x and yogii.
I can't install v6.0 but v6.1 work for me.
is this (v6.1)stable enough?
if not,can I back to 5.25?

paulmuhl · Mon May 27, 2013 7:52 pm

I have also a problem with CCR and v6 and still with 6.1.
Hotspot makes redirect to login page, login takes place and user shown as "active" in CCR, also in radius server, but no redirect to status page and no online surfing on other pages possible.
Downgrade to v6 rc13 and everything is working fine.
Also working wirth v6rc14 - but after upgrade to v6 final it is not more working!

EMOziko · Mon May 27, 2013 8:03 pm

We have v6 on 2 CCR and one x86 in production. Works great! Soon we will add more CCR's.

Hope in next releases, wireless will be priority too.

rogeriodj · Tue May 28, 2013 2:50 am

What we have to do to make this work to provide CCR?
Well anyway we tried, it has many problems! Processing high, with almost nothing in it, knocking OSPF ...

Tue May 28, 2013 5:30 am

Is anyone else experiencing DHCP server not working on v6 x86 ?
run sniffer files from clients and send to support. we have not yet had any reports.

Hi Normis, done and logged Ticket#2013052766000123

gogusrl · Tue May 28, 2013 9:07 am

I have this problem after I upgraded my 951g-2hnd to v6.0.

3bs · Tue May 28, 2013 9:39 am

multicast package still broken

Tue May 28, 2013 10:23 am

paulmuhl,
check /file print and make sure all HotSpot folders and files are present (run /ip hotspot reset-html to get files on your router).
If files are present, make support output file and send it to support department (support@mikrotik.com).

Rudios · Tue May 28, 2013 12:33 pm

I have this problem after I upgraded my 951g-2hnd to v6.0.

Has been mentioned before, MT support has been busy on my router, but it is not yet solved.
Also unfortunately I did not yet hear something back from them.

wpeople · Tue May 28, 2013 3:56 pm

Using RB493G with 2 wireless cards (wlan1 and wlan2). Both in AP mode, with 1-1 wds station connected.
When I select a new channel for wlan2, wlan1 disconnects as well. Of course, there is a big spacing between channels (100+ MHz)

both cards are running in 802.11-N and nv2, dual chain.

Anyone meet this? Or can reproduce?
(i've not met with this while running 5.x)

Tue May 28, 2013 4:06 pm

Using RB493G with 2 wireless cards (wlan1 and wlan2). Both in AP mode, with 1-1 wds station connected.
When I select a new channel for wlan2, wlan1 disconnects as well. Of course, there is a big spacing between channels (100+ MHz)

both cards are running in 802.11-N and nv2, dual chain.

Anyone meet this? Or can reproduce?
(i've not met with this while running 5.x)

please enable the wireless,debug logging, reproduce that and paste the log entries.

yogii · Tue May 28, 2013 5:13 pm

thanks simpl3x and yogii.
I can't install v6.0 but v6.1 work for me.
is this (v6.1)stable enough?
if not,can I back to 5.25?

of course you can. but i recomend to downgrade "rc" version.

hello MT Support,
yesterday my RB951-2n suddenly reboot when i tested to transfer data over wireless with routing mode and no BW limitation. this may be causing bottleneck and rebooted the RB. is it normal?

thank you..

Tue May 28, 2013 5:25 pm

tested 6.1rc1 (05/24/2013) all the way to (05/272013)
- NOT FIXED, still error in usermanager web-ui (web-ui ignoring timezone setting) - but no problem in cli (/tool user-manager session print)
- NEW ERROR, ip > hotspot > active - Session Time Left empty

Please redownload the new test release and check again.

sealin · Wed May 29, 2013 2:25 am

Hi,
I setup Ros5.25 & Ros6.0 in different Virtual PCs.
In each Ros, I add 1000 pppoe-client and 1000 routes.
I use scripts below:

:for sheng from=1 to=1000 do={/int pppoe-client
add interface=ether1 name=("pppoe-out" . $sheng) password=1 user=1}
:for sheng from=1 to=1000 do={/ip route
add disabled=yes distance=1 dst-address=0.0.0.0/0 gateway=("pppoe-out" . $sheng) routing-mark=$sheng scope=30 target-scope=10}

At last, I find that either Ros5.25 or Ros6.0 could enable more than 252 routes. If routes do not show reachable or unreachable, they can not be used in mangle.Here are pictures and supout files.
So Is the number of routes limited?
Thanks a lot.
Have a nice day!^_^

Stillhard · Wed May 29, 2013 7:17 am

tested 6.1rc1 (05/24/2013) all the way to (05/272013)
- NOT FIXED, still error in usermanager web-ui (web-ui ignoring timezone setting) - but no problem in cli (/tool user-manager session print)
- NEW ERROR, ip > hotspot > active - Session Time Left empty
Please redownload the new test release and check again.

tested 6.1rc1 (05/28/2013)
- NOT FIXED, still error in usermanager web-ui (web-ui ignoring timezone setting) - but no problem in cli (/tool user-manager session print)
- FIXED, ip > hotspot > active - Session Time Left empty
- NEW/OLD ERROR, ip > hotspot > active - Tx Rate stays in 0 bps

ringlet · Wed May 29, 2013 10:00 am

http://prntscr.com/177ezn

i have 22 channels in my scan list, previously it was in one line , now it is in some kind of matrix and a cant use nothing what is below matrix.

Wed May 29, 2013 10:09 am

http://prntscr.com/177ezn

i have 22 channels in my scan list, previously it was in one line , now it is in some kind of matrix and a cant use nothing what is below matrix.

This is normal. It is because in v6 you must use the Channels tab to define a list of channels. Then, in this window, only specify that channel list name.

adiputrasa · Wed May 29, 2013 11:40 am

Hi anyone using v6.1rc1 and success getting snmp? I got a problem after plug CCR with v6.1rc1 my cacti showed snmp error for those CCR Device

alexp89 · Wed May 29, 2013 12:10 pm

What about the problems with freezing SSH? (On 6.0 x86 accurately present) http://forum.mikrotik.com/viewtopic.php ... 62#p370862
Now ssh freezing causing a collapse of the router.

Chupaka · Wed May 29, 2013 4:40 pm

So Is the number of routes limited?

not the number of routes but the number of routing tables. to you really have more than 252 different gateways for policy routing?

dzieva · Wed May 29, 2013 6:50 pm

tested 6.1rc1 (05/24/2013) all the way to (05/272013)
- NOT FIXED, still error in usermanager web-ui (web-ui ignoring timezone setting) - but no problem in cli (/tool user-manager session print)
- NEW ERROR, ip > hotspot > active - Session Time Left empty

PPP Last Logged Out ignoring timezone setting (winbox)

ringlet · Wed May 29, 2013 7:54 pm

http://prntscr.com/177ezn

i have 22 channels in my scan list, previously it was in one line , now it is in some kind of matrix and a cant use nothing what is below matrix.
This is normal. It is because in v6 you must use the Channels tab to define a list of channels. Then, in this window, only specify that channel list name.

thx for response , can U show me how in easiest way migrate from "old" way of defining scan list to "new" one?

also i dont see any export button for this , and it looks very complicated way... till 5.25 i just copy-paste my favorite channels....
i have to change something about 300-400 devices... please help

samsung172 · Thu May 30, 2013 5:15 am

Make a tab in right corner, make it possible to scroll in winbox.

The change of one line per freq in scan list, make this function so much needed. From earlier, it was an issue to, but in so small grade. Now its an really big issue.

I have this scan list:

5390,5410,5430,5450,5470,5490,5510,5530,5550,5570,5590,5610,5630,5650,5670,5690,5180,5750,5770,5790,5810,5830,5850,5870,5890,5390,5410,5430,5450,5470,5490,5510,5530,5550,5570,5590,5610,5630,5650,5670,5690

Try this in 1024X768

ringlet · Thu May 30, 2013 9:15 am

do U think that it will be working?

/interface wireless channels add frequency=5000 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless channels add frequency=5020 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless channels add frequency=5040 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless channels add frequency=5060 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless channels add frequency=5080 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless channels add frequency=5100 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless channels add frequency=5120 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless channels add frequency=5140 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless channels add frequency=5160 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless channels add frequency=5340 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless channels add frequency=5360 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless channels add frequency=5380 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless channels add frequency=5400 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless channels add frequency=5420 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless channels add frequency=5440 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless channels add frequency=5460 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless channels add frequency=5480 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless channels add frequency=5720 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless channels add frequency=5740 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless channels add frequency=5760 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless channels add frequency=5780 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless channels add frequency=5800 width=20 band=5ghz-onlyn extension-channel=above-control list=maxnet
/interface wireless set wlan1 scan-list=default,maxnet

???

BETEPAH · Thu May 30, 2013 11:26 am

5 days uptime, 4 millions RX drops!

Без имени-1.png

on other side interface has 0 drops

kapulan · Thu May 30, 2013 1:27 pm

5 days uptime, 4 millions RX drops!
Без имени-1.png
on other side interface has 0 drops

The vlan packet drops only multi cpu x86&routerboards devices. Rb1100Ah and RB800 was one cpu and not make vlan packet drops."The physical Ethernet interface do not make packet drops.

Mikrotik fix this problem.

Regards.

Krisztian

gjp1000 · Thu May 30, 2013 2:33 pm

The queues dissapear after a short period of time from queue list and if try to added again i take this error message "couldn't add new simple queue-already have such name"

Thu May 30, 2013 2:34 pm

are you connecting via MAC address? Then this could happen. Use IP

gjp1000 · Thu May 30, 2013 2:52 pm

I connect with ip . Ι don't know if this happens because I change my ethernet card and then i restore a backup from 5.25

Thu May 30, 2013 2:54 pm

ringlet, yes it will work with such channels lists.

BETEPAH · Thu May 30, 2013 3:46 pm

5 days uptime, 4 millions RX drops!
Без имени-1.png
on other side interface has 0 drops
The vlan packet drops only multi cpu x86&routerboards devices. Rb1100Ah and RB800 was one cpu and not make vlan packet drops."The physical Ethernet interface do not make packet drops.

Mikrotik fix this problem.

Regards.

Krisztian

Where you seeing vlans? This is physical Ethernet interface on 82598EB adapter. I have vlan's on ether2 and ether3, but not on ether1. This interface connected from 0.5 meters patchcord to other server on Centos 6.4. This server have 0 drops.

Zeeester · Thu May 30, 2013 7:55 pm

The queues dissapear after a short period of time from queue list and if try to added again i take this error message "couldn't add new simple queue-already have such name"

Same here on RB493

Stillhard · Thu May 30, 2013 8:14 pm

tested 6.1rc1 (May/30/2013 09:54:26)
- NOT FIXED, error in usermanager web-ui (web-ui ignoring timezone setting)
- NOT FIXED, ip > hotspot > active - Bytes Out, Packets Out, Tx Rate, Tx Rate stays in 0 bps

fabiandr · Thu May 30, 2013 8:30 pm

The queues dissapear after a short period of time from queue list and if try to added again i take this error message "couldn't add new simple queue-already have such name"
Same here on RB493

Same here on CCR1036
only appear if the server restarts

shrek777 · Thu May 30, 2013 8:56 pm

its heppening with our ccrs very often, if you want to show disappeared queues again, enable it from terminal.

also i cannot add new queue without target

Thu May 30, 2013 9:05 pm

ringlet, yes it will work with such channels lists.

Yes. But antenna-gain/country is ignored when using channels. So tx is at max.

scampbell · Fri May 31, 2013 5:11 am

Upgraded RB450G from 5.24 to 6.0 and my meta-routers had all disappeared.

The virtual IF's were still present though but displayed unknown for meta-router.

Recreated the meta-routers with the same names and everything was then ok and all old data was present.

Fri May 31, 2013 9:53 am

tested 6.1rc1 (May/30/2013 09:54:26)
- NOT FIXED, error in usermanager web-ui (web-ui ignoring timezone setting)
- NOT FIXED, ip > hotspot > active - Bytes Out, Packets Out, Tx Rate, Tx Rate stays in 0 bps

can you give us remote access with that Hotspot counter issue? Email support please

Fri May 31, 2013 9:55 am

Hi anyone using v6.1rc1 and success getting snmp? I got a problem after plug CCR with v6.1rc1 my cacti showed snmp error for those CCR Device

v6.1 may 30 build SNMP works on our CCR. Contact support with more details please. We will try to fix it.

Stillhard · Fri May 31, 2013 10:44 am

tested 6.1rc1 (May/30/2013 09:54:26)
- NOT FIXED, error in usermanager web-ui (web-ui ignoring timezone setting)
- NOT FIXED, ip > hotspot > active - Bytes Out, Packets Out, Tx Rate, Tx Rate stays in 0 bps
can you give us remote access with that Hotspot counter issue? Email support please

I'm sorry normis i can't do that for now (company's policy/weekend here)

djras · Fri May 31, 2013 10:57 am

tested v6.1rc1
- NOT FIXED, Tools->Graphing->ResourceGraphs - CPU, HDD, Memory type = unknown

djras · Fri May 31, 2013 11:14 am

test v6.1rc1
The section "Switch" without need now?

Fri May 31, 2013 11:15 am

test v6.1rc1
The section "Switch" without need now?

I have same router and same version, yet I have the switch menu. Can you send us your supout.rif file to support@mikrotik.com? We will see why it's gone

Fri May 31, 2013 11:20 am

I'm sorry normis i can't do that for now (company's policy/weekend here)

In our hotspot, the counters are working. Are you sure you have traffic?

Stillhard · Fri May 31, 2013 11:30 am

I'm sorry normis i can't do that for now (company's policy/weekend here)
In our hotspot, the counters are working. Are you sure you have traffic?

Yes of course we do have traffics, fyi, it's from May/30/2013 09:54:26 release, is there a new one now? what version you're using now?

Fri May 31, 2013 11:32 am

I'm sorry normis i can't do that for now (company's policy/weekend here)
In our hotspot, the counters are working. Are you sure you have traffic?
Yes of course we do have traffics, fyi, it's from May/30/2013 09:54:26 release, is there a new one now? what version you're using now?

Yes, it is the latest. We would need access to solve this. Anybody else have this issue?

Stillhard · Fri May 31, 2013 11:40 am

Yes, it is the latest. We would need access to solve this. Anybody else have this issue?

With May/27/2013 08:19:48 release, there was no such problem(s) (except for the usermanager's web-ui ignoring timezone setting)

Fri May 31, 2013 11:47 am

Yes, it is the latest. We would need access to solve this. Anybody else have this issue?
With May/27/2013 08:19:48 release, there was no such problem(s) (except for the usermanager's web-ui ignoring timezone setting)

Do the bytes and packet fields show correct information? Only the TX speed is not showing?

djras · Fri May 31, 2013 11:52 am

test v6.1rc1
The section "Switch" without need now?
I have same router and same version, yet I have the switch menu. Can you send us your supout.rif file to support@mikrotik.com? We will see why it's gone

Now I will send support.rif but how I can return back version 6.0 from 6.1rc1? Try.
(6.1rc1 ignored upgrade/downgrade packages {5.25 6.0} in Files. Only 6.1rc1 accepted.)

Fri May 31, 2013 11:54 am

test v6.1rc1
The section "Switch" without need now?
I have same router and same version, yet I have the switch menu. Can you send us your supout.rif file to support@mikrotik.com? We will see why it's gone
Now I will send support.rif but how I can return back version 6.0 from 6.1rc1? Try.

upload 6.0 package and run command "/system package downgrade"

djras · Fri May 31, 2013 12:14 pm

upload 6.0 package and run command "/system package downgrade"

I am afraid to do it remotely. I have not the standard MAC address settings . If updating to the prevoisely version everything leaves that a downgrade everything MAC dumps in a default settings.

Fri May 31, 2013 12:31 pm

upload 6.0 package and run command "/system package downgrade"
I am afraid to do it remotely. I have not the standard MAC address settings . If updating to the prevoisely version everything leaves that a downgrade everything MAC dumps in a default settings.

If you have no major issues right now, I suggest to stay with v6.1

Stillhard · Fri May 31, 2013 12:47 pm

Yes, it is the latest. We would need access to solve this. Anybody else have this issue?
With May/27/2013 08:19:48 release, there was no such problem(s) (except for the usermanager's web-ui ignoring timezone setting)
Do the bytes and packet fields show correct information? Only the TX speed is not showing?

Well, i can't show you the pic right now, but yes, it's show the correct informations

mark · Fri May 31, 2013 2:15 pm

The queues dissapear after a short period of time from queue list and if try to added again i take this error message "couldn't add new simple queue-already have such name"

This happens on all my RB951 and SXT devices, too. They're accessible through the command shell, though.

I really hope that it is related to bridges disappearing and/or (independently) losing their IPv6 link-local addresses, and that all this can be fixed very soon.

In our [item X; Mark], the [Y; Mark] are working. […]

Normis, I don't meant to offend. Please accept this as my sincere advice, from one engineer to the other: The »it works for us« (»… and so should for you«) communicates on more than one level negatively. — It suggests that the customer is wrong. Even if this is the case, he is to be taken seriously and an (not *the*) error has a cause still to be found.
Furthermore it is anecdotal, unless you really had a test-case of 1'000 devices meant for QA in mind.
Finally the phrase is perceived in such a way that the issue won't be fixed or with low(est) priority.

There is something wrong and by communicating it we signal that we want to help you find the cause and help us fix a bug. You're, as Mikrotik or on behalf of, sometimes accepting that help, that's true, though, and held in high regard.

midnightman · Fri May 31, 2013 3:55 pm

V6 simple queues still Day/night not working.

If I set for day parent queue time: 06:00:00 - 1d 00:00:00
and for night parent queue time: 00:00:00 - 06:00:00

queue is shown "red" and not working... (ROS v.3, v.4, v.5 are OK) Where is the problem? Thanks!

Fri May 31, 2013 3:56 pm

V6 simple queues still Day/night not working.

If I set for day parent queue time: 06:00:00 - 1d 00:00:00
and for night parent queue time: 00:00:00 - 06:00:00

queue is shown "red" and not working... (ROS v.3, v.4, v.5 are OK) Where is the problem? Thanks!

It will be shown in RED when it's not the set time. When that time comes, it will turn active. Did you try using 23:59:59 instead of 0;0;0?

midnightman · Fri May 31, 2013 5:06 pm

in ROS 5.XX queues were still normal (not red)...I will try 23:59:59 thanks.

///Thanks Normis

Queues are working....really if queues are inactive they are "red"....

lukoramu · Sat Jun 01, 2013 9:39 am

The queues dissapear after a short period of time from queue list and if try to added again i take this error message "couldn't add new simple queue-already have such name"
Same here on RB493
Same here on CCR1036
only appear if the server restarts

It's happening on my CCR1036 too. I know queues are working - I see it from the interface statistics, but all counters in the Queue Tree (when queues are showing, of course) are stuck. "/queue tree print rate" doesn't work either.

P.S. I wouldn't say they dissapear after some period of time - for me, it's when I re-login.

djras · Sat Jun 01, 2013 11:52 am

tested ros v6.0 CCR1036-12G-4S (tile)

I have a problem with Parrent in Queue. If I create the general record for "Parent" I can't set some IP addresses. Records are created, but after use of parameters all queue counters stoped. if I put 1 ip the address that other counters work and all counters for Parent are stopped.

djras · Sat Jun 01, 2013 12:29 pm

The queues dissapear after a short period of time from queue list and if try to added again i take this error message "couldn't add new simple queue-already have such name"
.....
It's happening on my CCR1036 too. I know queues are working - I see it from the interface statistics, but all counters in the Queue Tree (when queues are showing, of course) are stuck. "/queue tree print rate" doesn't work either.

P.S. I wouldn't say they dissapear after some period of time - for me, it's when I re-login.

I think it other situation. I suggest that Queue service began to work another way. Instead of ignoring of lines with not right syntax he tries to execute interpretation them. These are only my guesses.

It is like the start of Unix Services. The firstly - a config rereading. The second - commands of service.
Where exactly there is a problem - a question to support.

gjp1000 · Sat Jun 01, 2013 12:48 pm

djras the ros 6 has several bugs with different things such as queues, lan drivers on x86 platform, etc, as you can read in this forum.
Im sure that Mikrotik team finally solve all these problems as usually

wwooley · Sat Jun 01, 2013 4:52 pm

Hotspot Issue:

RB450G > v6.0 > Hotspot
Problems:
login.html doesn't always load.
Once login attempted, no redirection or any website load.
Shows user session in Hosts/Users
Hotspot Files not complete - no login.html, alogin.html, etc

Installed v6.1rc1:
login.html loads quickly
redirects and web-browsing OK, except:
some websites will not load (aol.com, gmail, pogo.com, etc)

Downgraded to v5.24:
Running smoothly at this time.

NOTE: have left v6.1rc1 on remainder of eqpt in network.

On a POSITIVE Note:
As soon as we upgraded all of our eqpt to v6.0 (8 AP w/5.8 Backhauls), there was a NOTICEABLE IMPROVEMENT in network performance. improved WDS link CCQ, reduced latency, consistent client connections.

Thanks,
wwooley

chemil · Sat Jun 01, 2013 8:48 pm

Hi, I have a problem with the stability of IPSec LAN-to-LAN tunnel on the CCR1036
6.14rc - it seems that have this problem
6.0 - same as 6.14rc
6.1rc - doesn't even make a connection

My case fits best to http://forum.mikrotik.com/viewtopic.php?f=2&t=56944

I can provide access to my router if someone from support can help me.

juantete · Sun Jun 02, 2013 3:02 am

Hi, I have a X86 Installed with 3 ethernet interfaces, the update to version 6.0, the PCI Express interface ethernet 1, RTL8101E/RTL8102E Fast Ethernet controller (rev: 1) stopped working, I check in resources and PCI tab appears but no data traffic.

Can help with this.

Thanks.