Hello,
It is posible to make this configuration with 411R ?

Antena A ( wireless client) - Bridge - Antena B ( hotspot ) ?

Thank you and and if yes pls send tutorials

How many wlan's do you see in Interface page?

i have only wlan1 and ether1.

In that case how do you think that you can "split" an wireless card in two?

Yes if you setup rx and tx on both chains you could attach each chain to its own antenna and point them in different directions. For example an omni for the hotspot and a directional outdoor antenna for a client.

All connections would come into the same WLAN network card so you may want to setup bypass rules so the client doesn't have to bother with the hotspot stuff.

Also be aware that your client would be sharing the wireless resources with the hotspot so it would not be like having a dedicated link.

I would probably recommend getting a dedicated device for the client like an SXT however I don't have enough understanding of your situation to make a good recommendation.


Joshaven Potter
http://joshaven.com
Sent from my iPhone using Tapatalk

You can't not one radio card use as accesspoint and as client.

for this configuration
Inernet -> Wlan1 client wireless -> eth1 dhcp server -> user

can you give an tutorial ?

What will you just do?

Connect wireless with a wireless interface to internet or what?

i want this configuration:

Wireless card to be wireless client for an AP and from that to give on ethernet to have internet in my lan.

Thank you

Do you mean that you wireless will connect to a accesspoint.
Would you like to than via the ethernet interfaces on the internet?

Hello,
It is posible to make this configuration with 411R ?

Antena A ( wireless client) - Bridge - Antena B ( hotspot ) ?

Thank you and and if yes pls send tutorials

http://routerboard.com/RB411R

NO, in this model the wireless are integrated onboard, you can select only from this option:

[antenna A = main microFL connector onboard]
[antenna A = aux microFL connector onboard]

antenna A rx & tx
or
antenna B rx & tx
or
antenna A rx & Antenna B tx
or
antenna A tx & Antenna B rx


but you can not use as two distinct wireless module.

In that case how do you think that you can "split" an wireless card in two?

Why you not explain why?

Some answer can frustrating the newbie.

Everytime you say NOT [or YES...] try to explain the answer.

Yes if you setup rx and tx on both chains you could attach each chain to its own antenna and point them in different directions. For example an omni for the hotspot and a directional outdoor antenna for a client.

All connections would come into the same WLAN network card so you may want to setup bypass rules so the client doesn't have to bother with the hotspot stuff.

Also be aware that your client would be sharing the wireless resources with the hotspot so it would not be like having a dedicated link.

I would probably recommend getting a dedicated device for the client like an SXT however I don't have enough understanding of your situation to make a good recommendation.


Joshaven Potter
http://joshaven.com
Sent from my iPhone using Tapatalk

RB411A is only 802.11 b/g and not have MIMO.
Before answer in a post, is nice to read device physical characteristics.

You can't not one radio card use as accesspoint and as client.

Not totally true: the radio can be set [with License Level 4] as a-bridge with WDS, it act like client to other AP WDS and AP itself.

i want this configuration:

Wireless card to be wireless client for an AP and from that to give on ethernet to have internet in my lan.

Thank you

You can:
1) Reset any configuration;
2) add dhcp server on ether1 (by wizard);
3) add dhcp client on wlan1
4) add on firewall nat rule:src-nat out:wlan1 action:masquerade
5) open wireless / security profile and modify default profile with the password of AP (if AP have not password, skip this passage)
6) from wireless click on scan, select your AP from the list, and click on connect.

Done [I hope, if I not miss anything...].

Thank you very much for your asnwers. i will try

Hy,

I did what you say and is not working for me.

i have internet on dhcp modem - i create dhcp client on wlan1 and dhcpserver on ether1 after that i make the nat masquerade out interface wlan1.

and is now working. i receive unidentified network.

ps: my wlan1 was conected to ess.

Thank you,

paste your config here (/export compact on terminal)
remember to remove sensible data [if any]

[admin@MikroTik] > /export
# jan/01/1970 07:36:57 by RouterOS 3.22
# software id = V5JB-PTT
#
/interface ethernet
set 0 arp=enabled auto-negotiation=yes comment="" disabled=no full-duplex=yes \
mac-address=00:0C:42:27:72:2C mtu=1500 name=ether1 speed=100Mbps
/interface wireless security-profiles
set default authentication-types="" eap-methods=passthrough group-ciphers="" \
group-key-update=5m interim-update=0s mode=none name=default \
radius-eap-accounting=no radius-mac-accounting=no \
radius-mac-authentication=no radius-mac-caching=disabled \
radius-mac-format=XX:XX:XX:XX:XX:XX radius-mac-mode=as-username \
static-algo-0=none static-algo-1=none static-algo-2=none static-algo-3=\
none static-key-0="" static-key-1="" static-key-2="" static-key-3="" \
static-sta-private-algo=none static-sta-private-key="" \
static-transmit-key=key-0 supplicant-identity=MikroTik tls-certificate=\
none tls-mode=no-certificates unicast-ciphers="" wpa-pre-shared-key="" \
wpa2-pre-shared-key=""
add authentication-types=wpa2-psk group-ciphers=aes-ccm group-key-update=5m \
interim-update=0s mode=dynamic-keys name=necsys radius-eap-accounting=no \
radius-mac-accounting=no radius-mac-authentication=no radius-mac-caching=\
disabled radius-mac-format=XX:XX:XX:XX:XX:XX radius-mac-mode=as-username \
static-algo-0=none static-algo-1=none static-algo-2=none static-algo-3=\
none static-key-0="" static-key-1="" static-key-2="" static-key-3="" \
static-sta-private-algo=none static-sta-private-key="" \
static-transmit-key=key-0 supplicant-identity="" tls-certificate=none \
tls-mode=no-certificates unicast-ciphers=aes-ccm wpa-pre-shared-key=\
ndhe12022208 wpa2-pre-shared-key=ndhe12022208
/interface wireless
set 0 ack-timeout=dynamic adaptive-noise-immunity=none allow-sharedkey=no \
antenna-gain=0 antenna-mode=ant-a area="" arp=enabled band=2.4ghz-b/g \
basic-rates-a/g=6Mbps basic-rates-b=1Mbps burst-time=disabled comment="" \
compression=no country=no_country_set default-ap-tx-limit=0 \
default-authentication=yes default-client-tx-limit=0 default-forwarding=\
yes dfs-mode=none disable-running-check=no disabled=no \
disconnect-timeout=3s frame-lifetime=0 frequency=2412 frequency-mode=\
manual-txpower hide-ssid=no hw-retries=4 mac-address=00:0B:6B:2F:40:27 \
max-station-count=2007 mode=station mtu=1500 name=wlan1 \
noise-floor-threshold=default on-fail-retry-time=100ms \
periodic-calibration=default periodic-calibration-interval=60 \
preamble-mode=both proprietary-extensions=post-2.9.25 radio-name=\
000B6B2F4027 rate-set=default scan-list=default security-profile=necsys \
ssid="NecSys Technology" station-bridge-clone-mac=00:00:00:00:00:00 \
supported-rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54Mbps \
supported-rates-b=1Mbps,2Mbps,5.5Mbps,11Mbps tx-power-mode=default \
update-stats-interval=disabled wds-cost-range=50-150 wds-default-bridge=\
none wds-default-cost=100 wds-ignore-ssid=no wds-mode=disabled \
wmm-support=disabled
/interface wireless manual-tx-power-table
set wlan1 comment="" manual-tx-powers="1Mbps:17,2Mbps:17,5.5Mbps:17,11Mbps:17,\
6Mbps:17,9Mbps:17,12Mbps:17,18Mbps:17,24Mbps:17,36Mbps:17,48Mbps:17,54Mbps\
:17,HT20-1:0,HT20-2:0,HT20-3:0,HT20-4:0,HT20-5:0,HT20-6:0,HT20-7:0,HT20-8:\
0,HT40-1:0,HT40-2:0,HT40-3:0,HT40-4:0,HT40-5:0,HT40-6:0,HT40-7:0,HT40-8:0"
/interface wireless nstreme
set wlan1 comment="" disable-csma=no enable-nstreme=no enable-polling=yes \
framer-limit=3200 framer-policy=none
/ip hotspot profile
set default dns-name="" hotspot-address=0.0.0.0 html-directory=hotspot \
http-cookie-lifetime=3d http-proxy=0.0.0.0:0 login-by=cookie,http-chap \
name=default rate-limit="" smtp-server=0.0.0.0 split-user-domain=no \
use-radius=no
/ip hotspot user profile
set default idle-timeout=none keepalive-timeout=2m name=default shared-users=\
1 status-autorefresh=1m transparent-proxy=no
/ip ipsec proposal
set default auth-algorithms=sha1 disabled=no enc-algorithms=3des lifetime=30m \
name=default pfs-group=modp1024
/ip pool
add name=dhcp_pool1 ranges=192.168.10.2-192.168.10.254
/ip dhcp-server
add address-pool=dhcp_pool1 authoritative=after-2sec-delay bootp-support=\
static disabled=no interface=ether1 lease-time=3d name=dhcp1 src-address=\
192.168.10.1
/port
set 0 baud-rate=auto data-bits=8 flow-control=none name=serial0 parity=none \
stop-bits=1
/ppp profile
set default change-tcp-mss=yes comment="" name=default only-one=default \
use-compression=default use-encryption=default use-vj-compression=default
set default-encryption change-tcp-mss=yes comment="" name=default-encryption \
only-one=default use-compression=default use-encryption=yes \
use-vj-compression=default
/queue type
set default kind=pfifo name=default pfifo-limit=50
set ethernet-default kind=pfifo name=ethernet-default pfifo-limit=50
set wireless-default kind=sfq name=wireless-default sfq-allot=1514 \
sfq-perturb=5
set synchronous-default kind=red name=synchronous-default red-avg-packet=1000 \
red-burst=20 red-limit=60 red-max-threshold=50 red-min-threshold=10
set hotspot-default kind=sfq name=hotspot-default sfq-allot=1514 sfq-perturb=\
5
set default-small kind=pfifo name=default-small pfifo-limit=10
/routing bgp instance
set default as=65530 client-to-client-reflection=yes comment="" disabled=no \
ignore-as-path-len=no name=default out-filter="" redistribute-connected=\
no redistribute-ospf=no redistribute-other-bgp=no redistribute-rip=no \
redistribute-static=no router-id=0.0.0.0
/routing ospf area
add area-id=0.0.0.0 authentication=none disabled=no name=backbone type=\
default
/snmp
set contact="" enabled=no engine-boots=0 engine-id="" location="" \
time-window=15 trap-sink=0.0.0.0 trap-version=1
/snmp community
set public address=0.0.0.0/0 authentication-password="" \
authentication-protocol=MD5 encryption-password="" encryption-protocol=\
DES name=public read-access=yes security=none write-access=no
/system logging action
set memory memory-lines=100 memory-stop-on-full=no name=memory target=memory
set disk disk-file-count=2 disk-file-name=log disk-lines-per-file=100 \
disk-stop-on-full=no name=disk target=disk
set echo name=echo remember=yes target=echo
set remote bsd-syslog=no name=remote remote=0.0.0.0:514 src-address=0.0.0.0 \
syslog-facility=daemon syslog-severity=auto target=remote
/system routerboard settings
set baud-rate=115200 boot-delay=2s boot-device=nand-if-fail-then-ethernet \
boot-protocol=bootp cpu-frequency=300MHz enable-jumper-reset=yes \
enter-setup-on=any-key force-backup-booter=no
set baud-rate=115200 boot-delay=2s boot-device=nand-if-fail-then-ethernet \
boot-protocol=bootp cpu-frequency=300MHz enable-jumper-reset=yes \
enter-setup-on=any-key force-backup-booter=no
/user group
add name=read policy="local,telnet,ssh,reboot,read,test,winbox,password,web,sn\
iff,!ftp,!write,!policy"
add name=write policy="local,telnet,ssh,reboot,read,write,test,winbox,password\
,web,sniff,!ftp,!policy"
add name=full policy="local,telnet,ssh,ftp,reboot,read,write,policy,test,winbo\
x,password,web,sniff"
/interface bridge settings
set use-ip-firewall=no use-ip-firewall-for-pppoe=no use-ip-firewall-for-vlan=\
no
/interface ethernet mirror
set mirror-port=none source-port=none
/interface l2tp-server server
set authentication=pap,chap,mschap1,mschap2 default-profile=\
default-encryption enabled=no max-mru=1460 max-mtu=1460 mrru=disabled
/interface ovpn-server server
set auth=sha1,md5 certificate=none cipher=blowfish128,aes128 default-profile=\
default enabled=no keepalive-timeout=60 mac-address=FE:2D:44:C7:39:4D \
max-mtu=1500 mode=ip netmask=24 port=1194 require-client-certificate=no
/interface pptp-server server
set authentication=mschap1,mschap2 default-profile=default-encryption \
enabled=no keepalive-timeout=30 max-mru=1460 max-mtu=1460 mrru=disabled
/interface wireless align
set active-mode=yes audio-max=-20 audio-min=-100 audio-monitor=\
00:00:00:00:00:00 filter-mac=00:00:00:00:00:00 frame-size=300 \
frames-per-second=25 receive-all=no ssid-all=no
/interface wireless sniffer
set channel-time=200ms file-limit=10 file-name="" memory-limit=10 \
multiple-channels=no only-headers=no receive-errors=no streaming-enabled=\
no streaming-max-rate=0 streaming-server=0.0.0.0
/interface wireless snooper
set channel-time=200ms multiple-channels=yes receive-errors=no
/ip accounting
set account-local-traffic=no enabled=no threshold=256
/ip accounting web-access
set accessible-via-web=no address=0.0.0.0/0
/ip dhcp-client
add add-default-route=yes comment="" default-route-distance=0 disabled=no \
interface=wlan1 use-peer-dns=yes use-peer-ntp=yes
/ip dhcp-server config
set store-leases-disk=5m
/ip dhcp-server network
add address=192.168.10.0/24 comment="" dns-server=8.8.8.8 gateway=\
192.168.10.1
/ip dns
set allow-remote-requests=no cache-max-ttl=1w cache-size=2048KiB \
max-udp-packet-size=512 primary-dns=192.168.1.1 secondary-dns=192.168.1.1
/ip firewall connection tracking
set enabled=yes generic-timeout=10m icmp-timeout=10s tcp-close-timeout=10s \
tcp-close-wait-timeout=10s tcp-established-timeout=1d \
tcp-fin-wait-timeout=10s tcp-last-ack-timeout=10s \
tcp-syn-received-timeout=5s tcp-syn-sent-timeout=5s tcp-syncookie=no \
tcp-time-wait-timeout=10s udp-stream-timeout=3m udp-timeout=10s
/ip firewall nat
add action=masquerade chain=srcnat comment="" disabled=no out-interface=wlan1
/ip firewall service-port
set ftp disabled=no ports=21
set tftp disabled=no ports=69
set irc disabled=no ports=6667
set h323 disabled=no
set sip disabled=no ports=5060,5061
set pptp disabled=no
/ip hotspot service-port
set ftp disabled=no ports=21
/ip neighbor discovery
set ether1 discover=yes
set wlan1 discover=no
/ip proxy
set always-from-cache=no cache-administrator=webmaster cache-hit-dscp=4 \
cache-on-disk=no enabled=no max-cache-size=unlimited \
max-client-connections=600 max-fresh-time=3d max-server-connections=600 \
parent-proxy=0.0.0.0 parent-proxy-port=0 port=8080 serialize-connections=\
no src-address=0.0.0.0
/ip service
set telnet address=0.0.0.0/0 disabled=no port=23
set ftp address=0.0.0.0/0 disabled=no port=21
set www address=0.0.0.0/0 disabled=no port=80
set ssh address=0.0.0.0/0 disabled=no port=22
set www-ssl address=0.0.0.0/0 certificate=none disabled=yes port=443
set api address=0.0.0.0/0 disabled=yes port=8728
set winbox address=0.0.0.0/0 disabled=no port=8291
/ip socks
set connection-idle-timeout=2m enabled=no max-connections=200 port=1080
/ip traffic-flow
set active-flow-timeout=30m cache-entries=4k enabled=no \
inactive-flow-timeout=15s interfaces=all
/ip upnp
set allow-disable-external-interface=yes enabled=no show-dummy-rule=yes
/ppp aaa
set accounting=yes interim-update=0s use-radius=no
/queue interface
set ether1 queue=ethernet-default
set wlan1 queue=wireless-default
/radius incoming
set accept=no port=3799
/routing mme
set bidirectional-timeout=2 gateway-class=none gateway-keepalive=1m \
gateway-selection=no-gateway origination-interval=5s preferred-gateway=\
0.0.0.0 timeout=1m ttl=50
/routing ospf
set distribute-default=never metric-bgp=20 metric-connected=20 \
metric-default=1 metric-rip=20 metric-static=20 mpls-te-area=unspecified \
mpls-te-router-id=unspecified redistribute-bgp=no redistribute-connected=\
no redistribute-rip=no redistribute-static=no router-id=0.0.0.0
/routing rip
set distribute-default=never garbage-timer=2m metric-bgp=1 metric-connected=1 \
metric-default=1 metric-ospf=1 metric-static=1 redistribute-bgp=no \
redistribute-connected=no redistribute-ospf=no redistribute-static=no \
timeout-timer=3m update-timer=30s
/store
add comment="" disabled=no disk=system name=web-proxy1 type=web-proxy
/system clock manual
set dst-delta=+00:00 dst-end="jan/01/1970 00:00:00" dst-start=\
"jan/01/1970 00:00:00" time-zone=+00:00
/system console
add disabled=no port=serial0 term=vt102
/system health
set fan-mode=auto use-fan=main
/system identity
set name=MikroTik
/system logging
add action=memory disabled=no prefix="" topics=info
add action=memory disabled=no prefix="" topics=error
add action=memory disabled=no prefix="" topics=warning
add action=echo disabled=no prefix="" topics=critical
/system note
set note="" show-at-login=yes
/system ntp client
set enabled=no mode=broadcast primary-ntp=0.0.0.0 secondary-ntp=0.0.0.0
/system upgrade mirror
set check-interval=1d enabled=no primary-server=0.0.0.0 secondary-server=\
0.0.0.0 user=""
/system watchdog
set auto-send-supout=no automatic-supout=yes no-ping-delay=5m watch-address=\
none watchdog-timer=yes
/tool bandwidth-server
set allocate-udp-ports-from=2000 authenticate=yes enabled=yes max-sessions=10
/tool e-mail
set from=<> password="" server=0.0.0.0:25 username=""
/tool graphing
set store-every=5min
/tool mac-server
add disabled=no interface=all
/tool mac-server ping
set enabled=yes
/tool sniffer
set file-limit=10 file-name="" filter-address1=0.0.0.0/0:0-65535 \
filter-address2=0.0.0.0/0:0-65535 filter-protocol=ip-only filter-stream=\
yes interface=all memory-limit=10 only-headers=no streaming-enabled=no \
streaming-server=0.0.0.0
/user aaa
set accounting=yes default-group=read interim-update=0s use-radius=no

Uh... RouterOS 3.22...

Think about upgrade RouterOS to 4.17,
upgrade licence key,
then upgrade to RouterOS 5.26,
upgrade the bios [firmware] to 3.10,
then upgrade to RouterOS 6.11...

wait one moment, i fix the script....

Changes to be made in your config:
Miossing IP Address on ether1 192.168.10.1/24
on wlan1 advanced, hw-retries must be 7, the standard. Not the old value 4 [...]
src-address on DHCP server must not be specified [...]
on DHCP network, the DNS server must be 192.168.10.1
DNS client/server are not active,
DNS have "old" max-udp-packet-size, now must be 4096
Also are missing both DNS [if the DHCP client do not provide DNS]
neighbor discovery are disabled on wlan1

thank you