Community discussions

MikroTik App
 
Adrenaline1965
just joined
Topic Author
Posts: 14
Joined: Fri Jun 20, 2014 1:41 pm

How to configure a CRS125-24G-15-RM as a flat L2 switch

Fri Jun 20, 2014 2:16 pm

I want to use my CRS125-24G-15-RM as a plain flat L2 switch w/o any routing and/or firewalling features with the SFP1 port as uplink to my router/cable modem and the 24 eth ports as L2 switch ports. How can I achieve this?

My first idea was to:
  • Define eth1 as Master
  • Make eth2-24 Slave to eth1
  • Create a Bridge between sfp1 and eth1
  • Remove all L3 features (IP Addresses, DHCP,...)
However, I'm afraid by doing this I will loose my connection with the device, so it might be needed to have one port "reserved" for maintenance (make it a separate master) and have e.g. 192.168.88.1 assigned to it.

Furthermore I suspect the above config will have all traffic going to/from the router (via sfp1) processed by the CPU as it is bridged with eth1, which may be suboptimal as far as throughput is concerned...

So it might be better not to create a Bridge between sfp1 and eth1, use eth1 as the uplink to my router/cable modem and use sfp1 as a maintenance port (with 192.168.88.1 assigned to it).

Any advise would be welcome!
 
mervincm
Frequent Visitor
Frequent Visitor
Posts: 55
Joined: Sat May 17, 2014 10:02 pm
Location: Canada

Re: How to configure a CRS125-24G-15-RM as a flat L2 switch

Fri Jun 20, 2014 10:33 pm

[*]Remove all L3 features (IP Addresses, DHCP,...)[/*][/list]

However, I'm afraid by doing this I will loose my connection with the device.
You can manage the switch via winbox by putting in the mac address. I have done it.

That being said, I suspect you should be able to assign an ip without being forced into having more switch groups.
 
Adrenaline1965
just joined
Topic Author
Posts: 14
Joined: Fri Jun 20, 2014 1:41 pm

Re: How to configure a CRS125-24G-15-RM as a flat L2 switch

Sat Jun 21, 2014 2:33 pm

You can manage the switch via winbox by putting in the mac address. I have done it.

That being said, I suspect you should be able to assign an ip without being forced into having more switch groups.
Indeed, that worked just fine! This way I was able to strip the Cloud Switch to the bare essential. I removed:
  • IP Adresses
  • DHCP Client and server settings
  • ALL Firewall filters
  • ALL NAT settings
  • Pools
  • whatever I forgot...
And just kept one Master port (ether1) en made all other ethernet ports (ether2 torough ether24) slave to ether1 and it works great as a plane and simple L2 switch with sfp1 bridged to ether1 (but not used for the time being <= I don't have a sfp module at this time)

Thanks for the hint!
 
jkarras
Member Candidate
Member Candidate
Posts: 226
Joined: Fri Sep 06, 2013 3:07 am
Location: Utah, USA

Re: How to configure a CRS125-24G-15-RM as a flat L2 switch

Sat Jun 21, 2014 11:52 pm

Just assign a IP to the master port (static or DHCP). Assuming you want to setup a separate mgmt VLAN you could create a VLAN interface with the appropriate VLAN ID on the master port as well. If you want to keep the switch from forwarding L3 traffic turn off IP forwarding under the IP->Settings menu.


Why the bridge between the SFP port and eth1? Can it not just be a slave like the other ports?
 
mervincm
Frequent Visitor
Frequent Visitor
Posts: 55
Joined: Sat May 17, 2014 10:02 pm
Location: Canada

Re: How to configure a CRS125-24G-15-RM as a flat L2 switch

Mon Jun 23, 2014 9:12 pm

Why the bridge between the SFP port and eth1? Can it not just be a slave like the other ports?
I don't know about the CRS125, but on my CRS226 the 2 SFP+ ports can indeed be slaves of the same single master port.
 
jkarras
Member Candidate
Member Candidate
Posts: 226
Joined: Fri Sep 06, 2013 3:07 am
Location: Utah, USA

Re: How to configure a CRS125-24G-15-RM as a flat L2 switch

Tue Jun 24, 2014 2:36 am

The block diagram would agree.
 
leonset
Member Candidate
Member Candidate
Posts: 256
Joined: Wed Apr 01, 2009 9:09 pm

Re: How to configure a CRS125-24G-15-RM as a flat L2 switch

Tue Jun 24, 2014 11:00 am

In CRS125 just make SFP1 slave of whichever master-port you had defined and all switching will be done in the switch-chip without using the CPU. Don't use bridge.

We all need to learn that CRS must be setup in a different way than the previous routerboards: it has a powerfull switch chip which can do lots of things without using the RB's CPU. Indeed, I like to think that they are a switch plus an independent, single port, routerOS device connected to a special port called switch1-cpu, all in a single box.
 
Adrenaline1965
just joined
Topic Author
Posts: 14
Joined: Fri Jun 20, 2014 1:41 pm

Re: How to configure a CRS125-24G-15-RM as a flat L2 switch

Wed Jun 25, 2014 9:14 pm

Just assign a IP to the master port (static or DHCP). Assuming you want to setup a separate mgmt VLAN you could create a VLAN interface with the appropriate VLAN ID on the master port as well. If you want to keep the switch from forwarding L3 traffic turn off IP forwarding under the IP->Settings menu.


Why the bridge between the SFP port and eth1? Can it not just be a slave like the other ports?
Thanks for the suggestions! I don't need a separate mgmt VLAN in my very simple home network setup, I just need to be able to access the switch and this seems to be perfectly possible using the MAC address of the port I connect to.

I'll check the IP forwarding setting later, but I think I stripped mest of the L3 features/services already

I assumed the SFP1 port was not connected to the switch chip as is the case for many of the older Mikrotik models (where you have to bridge them), but if that's not correct (as it seems from the various replies I received thus far) I'll make it a slave to ether1 (or make the SFP1 master and all ether ports slave). I checked the block diagram and this seems to be correct.

Thank you all for helping me out! I'm becoming a true Mikrotik believer! ;-)
 
jkarras
Member Candidate
Member Candidate
Posts: 226
Joined: Fri Sep 06, 2013 3:07 am
Location: Utah, USA

Re: How to configure a CRS125-24G-15-RM as a flat L2 switch

Thu Jun 26, 2014 2:41 am

Personally I would still set a IP address on the master port for managing. Its much more reliable to use IP management over MAC address based management I have found.

Who is online

Users browsing this forum: qatar2022 and 9 guests