I have an RB951Ui-2HnD router.
Everything was fine before.
Now 5th port LED lights red as soon as power is supplied. At the same time everything is working.
Settings do not change anything. Even a full reset.
5th port activity is displayed in green. As a result, the color becomes orange (green+red). I do NOT use POE input on the 1st port and do NOT used POE output on 5th port (any POE on any port).
What a... ?
Re: Red LED RB951
that's because you forced POE on, on that port or you connected some device which require POE.
RB951Ui-2HnD is POE out capable on port 5
cheers
RB951Ui-2HnD is POE out capable on port 5
cheers
Re: Red LED RB951
This is my settings for 5th port:that's because you forced POE on, on that port or you connected some device which require POE.
RB951Ui-2HnD is POE out capable on port 5
cheers
... nothing changes if i pull out ALL the wires from the router.
Re: Red LED RB951
did you upgrade your router recently? - might be a bug
try amending the POE Port settings to auto.
please do a and if you have any output please paste here
Cheers
try amending the POE Port settings to auto.
please do a
Code: Select all
/interface eth exportCheers
Re: Red LED RB951
Auto on - the same red led.did you upgrade your router recently? - might be a bug
try amending the POE Port settings to auto.
please do aand if you have any output please paste hereCode: Select all/interface eth export
Cheers
Yes i was upgrade the firmware [6.15] AND the routerboard [3.16] recently.
Code: Select all
[admin@MikroTik] > /interface eth export
# jun/25/2014 18:05:10 by RouterOS 6.15
# software id = PF8F-Q7CX
#
/interface ethernet
set [ find default-name=ether5 ] advertise=100M-full name=5_IN
set [ find default-name=ether1 ] disabled=yes name=ether1-gate
set [ find default-name=ether2 ] name=ether2-master-local
set [ find default-name=ether3 ] master-port=ether2-master-loc
ether3-slave-local
set [ find default-name=ether4 ] master-port=ether2-master-loc
ether4-slave-local
[admin@MikroTik] >
[admin@MikroTik] >
Re: Red LED RB951
I suggest you create a supout.rif and send it to mktk support. they'll open a ticket for you.
Looks like a bug.
after that downgrade to 6.10 - that's the most stable version I know!!
cheers
Looks like a bug.
after that downgrade to 6.10 - that's the most stable version I know!!
cheers
Re: Red LED RB951
something else... have you played with the system leds settings?
I've just taken a brand new one and upgrade and it doesn't happen the same to me.
Check your system leds settings do they look like below?
cheers
I've just taken a brand new one and upgrade and it doesn't happen the same to me.
Check your system leds settings do they look like below?
Code: Select all
/system leds
set 0 disabled=no interface=wlan1 leds=wlan-led type=wireless-status
set 1 disabled=no interface=ether1 leds=led1 type=interface-activity
set 2 disabled=no interface=ether2 leds=led2 type=interface-activity
set 3 disabled=no interface=ether3 leds=led3 type=interface-activity
set 4 disabled=no interface=ether4 leds=led4 type=interface-activity
set 5 disabled=no interface=ether5 leds=led5 type=interface-activity
Re: Red LED RB951
These settings do not help.something else... have you played with the system leds settings?
I've just taken a brand new one and upgrade and it doesn't happen the same to me.
Check your system leds settings do they look like below?cheersCode: Select all/system leds set 0 disabled=no interface=wlan1 leds=wlan-led type=wireless-status set 1 disabled=no interface=ether1 leds=led1 type=interface-activity set 2 disabled=no interface=ether2 leds=led2 type=interface-activity set 3 disabled=no interface=ether3 leds=led3 type=interface-activity set 4 disabled=no interface=ether4 leds=led4 type=interface-activity set 5 disabled=no interface=ether5 leds=led5 type=interface-activity
For example if i make settings like on screen
red led still ON.
On normal led settings green leds are ACT.
Re: Red LED RB951
As far as I can see all your LED settings are disabled...These settings do not help.something else... have you played with the system leds settings?
I've just taken a brand new one and upgrade and it doesn't happen the same to me.
Check your system leds settings do they look like below?cheersCode: Select all/system leds set 0 disabled=no interface=wlan1 leds=wlan-led type=wireless-status set 1 disabled=no interface=ether1 leds=led1 type=interface-activity set 2 disabled=no interface=ether2 leds=led2 type=interface-activity set 3 disabled=no interface=ether3 leds=led3 type=interface-activity set 4 disabled=no interface=ether4 leds=led4 type=interface-activity set 5 disabled=no interface=ether5 leds=led5 type=interface-activity
For example if i make settings like on screen
red led still ON.
On normal led settings green leds are ACT.
You've tried enabling them I assume. Also have you tried replacing the cable on port 5?
other than that... create a supout.rif and send it to MKTK support maybe they can tell you more... I've only seen that happening if the port has POE output but obviously from what you describe is not the case.
cheers
Re: Red LED RB951
donecreate a supout.rif and send it to MKTK support maybe they can tell you more
You do not have the required permissions to view the files attached to this post.
Re: Red LED RB951
have you sent it to support@mikrotik.com?
Re: Red LED RB951
right... something happened with your interfaces
They should be like this:
0 ->eth1
1 ->eth2
........
4 ->eth5
for some reason 0 is eth5 and 1 is eth 1!
also something I see in the routerboard section:
I'm not sure if "bad command bios" means anything bad.
before anything try setting your interface 5_IN to POE auto on and to advertise
If no change I suggest to netinstall the ROS again and begin re-configuring from scratch
cheers
Code: Select all
Flags: X - disabled, R - running, S - slave
0 R name="5_IN" default-name="ether5" mtu=1500 l2mtu=1598
mac-address=00:0C:42:8B:93:6D orig-mac-address=00:0C:42:8B:93:6D
arp=enabled auto-negotiation=yes advertise=100M-full full-duplex=yes
tx-flow-control=off rx-flow-control=off speed=100Mbps master-port=none
bandwidth=unlimited/unlimited switch=switch1 poe-out=off
poe-priority=10
1 X name="ether1-gateway" default-name="ether1" mtu=1500 l2mtu=1598
mac-address=00:0C:42:8B:93:69 orig-mac-address=00:0C:42:8B:93:69
arp=enabled auto-negotiation=yes
advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full
full-duplex=yes tx-flow-control=off rx-flow-control=off speed=100Mbps
master-port=none bandwidth=unlimited/unlimited switch=switch1
poe-out=auto-on poe-priority=10
2 RS name="ether2-master-local" default-name="ether2" mtu=1500 l2mtu=1598
mac-address=00:0C:42:8B:93:6A orig-mac-address=00:0C:42:8B:93:6A
arp=enabled auto-negotiation=yes
advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full
full-duplex=yes tx-flow-control=off rx-flow-control=off speed=100Mbps
master-port=none bandwidth=unlimited/unlimited switch=switch1
poe-out=auto-on poe-priority=10
3 S name="ether3-slave-local" default-name="ether3" mtu=1500 l2mtu=1598
mac-address=00:0C:42:8B:93:6B orig-mac-address=00:0C:42:8B:93:6B
arp=enabled auto-negotiation=yes
advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full
full-duplex=yes tx-flow-control=off rx-flow-control=off speed=100Mbps
master-port=ether2-master-local bandwidth=unlimited/unlimited
switch=switch1 poe-out=auto-on poe-priority=10
4 RS name="ether4-slave-local" default-name="ether4" mtu=1500 l2mtu=1598
mac-address=00:0C:42:8B:93:6C orig-mac-address=00:0C:42:8B:93:6C
arp=enabled auto-negotiation=yes
advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full
full-duplex=yes tx-flow-control=off rx-flow-control=off speed=100Mbps
master-port=ether2-master-local bandwidth=unlimited/unlimited
switch=switch1 poe-out=auto-on poe-priority=10
0 ->eth1
1 ->eth2
........
4 ->eth5
for some reason 0 is eth5 and 1 is eth 1!
also something I see in the routerboard section:
Code: Select all
routerboard: yes
model: 951Ui-2HnD
serial-number: 43CE0156CBDE
current-firmware: 3.16
upgrade-firmware: 3.16
BIOS
bad command name bios (line 3 column 18)
SETTINGS
boot-device: nand-if-fail-then-ethernet
cpu-frequency: 600MHz
boot-protocol: bootp
force-backup-booter: no
silent-boot: nobefore anything try setting your interface 5_IN to POE auto on and to advertise
Code: Select all
auto-negotiation=yes advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full full-duplex=yescheers
Re: Red LED RB951
hmm...
after all i was NOT change anything and somehow red led now is OFF.
hmm...
after all i was NOT change anything and somehow red led now is OFF.
hmm...
Re: Red LED RB951
maybe you've changed something which required a reboot...
Re: Red LED RB951
Hello Friends, i am also getting Red LED problem in mikrotik RB951ui-2hnd which is continuously lighting red led.
i have also attached supout.rif file and picture of my router.
please help me to get out from this problem. thank you
i have also attached supout.rif file and picture of my router.
please help me to get out from this problem. thank you
You do not have the required permissions to view the files attached to this post.
Re: Red LED RB951 [SOLVED]
Red color LED just means "PoE-out" on port 5.
Re: Red LED RB951
Once every three years!
Who is online
Users browsing this forum: No registered users and 5 guests